Found one -- Thanks.
Jim - W0EB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please
Except for putting in the 100w amp, I’ve finally completed the kit. Whew! It
was harder than I thought. I’m 72 and my fingers no longer have the dexterity
they once had. But I got it done! The hardest part: Installing the KREF3 board
(page 48). I dang near had a heart attack! Hi hi. Thanks for
I should have mentioned that the kit I completed is a K3. I’m still working on
configuring it. I’m currently getting an error on power up (KAT3). I have an
email into support.
Carl Yaffey K8NU
Banjo, guitar, bass, mandolin, dobro.
recording studio.
cyaffeyno_s...@gmail.com
614 268 6353,
I have revised the original file -
https://drive.google.com/file/d/0B_D41ceK5uSqM3VGa05BWXBhYkE/edit?usp=sharing
And I added a couple layouts for anyone wanting to make a series of these on a
6x9 sheet of copper clad - 2 files(front and back) -
Can anyone assist me on how to take a off air recorded signal that’s on the
K3’s DVR and convert it into an MP3 file that I could email?
thanks in advance
todd
WB2ZAB
__
Elecraft mailing list
Home:
On 1/30/2014 11:12 AM, todd ruby wrote:
Can anyone assist me on how to take a off air recorded signal that’s
on the K3’s DVR and convert it into an MP3 file that I could email?
Connect LINE OUT to the LINE IN on a computer, fire up a recorder [I use
RecAll, but one of the free audio editors
Output power of my K3/100, SN 79xx, without KAT3 is very unstable in DATA A
mode. The symptom is;
1. With setting 100W output on 14MHz and 10MHz, I get 100W output for a couple
of seconds, then suddenly the output goes down to 10W or so.
2. On 7MHz and below, the output power never go up to
I have replaced my PR6 with the PR6-10 and it is now surplus to my needs. I
am asking $110 and I will ship within USA. Outside USA at actual cost.
PayPal preferred.
Jim/N1NK
__
Elecraft mailing list
Home:
Keith,
Have you adjusted your audio input to produce 4 bars solid on the ALC
meter with the 5th bar flashing?
If not, please do so - you can do that with the K3 in TX TEST mode so no
signal is transmitted.
After you set the audio level correctly, then adjust the power knob to
the desired
then using the K3 in DATA A mode
this often is caused by incorrect audio levels
the k3's audio level should show 4 bars with the 5th bar flickering
I have run my K3 with the 5th bar solid and it still worked ok
the power out level is set by the K3's PWR knob
most other rigs have a different
Don and John,
Thank you so much for coming to my aid with these baffling (to me) problems.
I have undertaken both your suggestions but still, unfortunately, no joy.
The J3+ issue The J3+ lead now gives a voltage reading of -0.225 volts while
covering the PA transistors with a thick cardboard and
Bill,
Regarding T4, there is one other possibility that I did not mention
before. If the direction of the windings is not as shown in the manual,
it will work backwards which may be what you are observing.
As for the minimum voltage of 1.4 volts, that is WAY too high. The
bridge should
We've just updated the shipping status page at
http://www.elecraft.com/elecraft_shipping_status.htm with the following KXPA100
information:
---
New KXPA100 orders should now ship within 3 weeks after order.
The following dates reflect California PDT (GMT-7) times:
We are now notifying
Got a new K3 and everything appears to be working fine except I have no
CW side tone in the headset. When I unplug the headset then I hear the
side tone. Same situation with setting the MON level. What parameter do
I need to set to correct this issue?
Thanks for the help.
Randy, AA8R
Could we all remember to put the Elecraft product ID in the subject of
our messages? A lot of us filter on those. I don't have an Elecraft
wattmeter, and I doubt I ever will so a W2 helps me get rid of those.
More importantly, a subject of Lost Sidetone strongly suggests K2, but
could be a
A friend on another list came up with the idea of an all-mode
transceiver for 2m and above.
It would be especially nice to see coverage of 1.25m, and possibly 70cm,
33 cm and 23 cm.
If such support for 1.25m, especially, is forthcoming, it looks like an
American manufacturer would be the best
Does your headset have a stereo plug?
-
73, Stan - KR7C
--
View this message in context:
http://elecraft.365791.n2.nabble.com/No-CW-Side-tone-or-MON-with-headset-tp7583466p7583469.html
Sent from the Elecraft mailing list archive at Nabble.com.
17 matches
Mail list logo