Louis,
That is normally a result of one or more unsoldered connections or a
poorly soldered connections on either Front Panel U1 or the LCD itself.
Check the LCD leads first - you might want to solder them from the top
of the board if you do not see solder wicked up onto the leads.
U1 is a
Another noisy net, with 29 participants.
Remember that I may not make it to the net this coming Sunday. If not, I hope
someone can fill in.
Here is the list of stations:
CALLNAMEQTH RIG
W4PFM PaulVA K3
Hi Dave,
If the K3 is running Beta MCU 5.26 then there is a new configuration setting
which applies when the KXV3B is installed. Here is the explanation from the
5.26 notes.
* PREAMP 2 and CONFIG:PREAMP2 MENU ENTRY (KXV3B): This menu entry is only
applicable if a KXV3B module is installed
Hi Wayne and all at Elecraft.
My K3 circa 2/2008 was originally purchased
without a KXV3.
I may be interested in the KXV3B for my K3 as the
K3S FAQ's indicate is possible to do.
But the KXV3B manual now on the download page Rev.
C dated May 27, 2015 does not mention anything
about the
Hey!
I have an Elecraft K2, serial number 7535, with the following options
installed: KSB2, KNB2, KIO2, KAT2, KBT2, and K160RX. I just installed the
K160RX board tonight after sitting on the kit for about a year and finally
set out to build it today. Once I installed it I did the basic checks
Elecraft will be attending both SeaPac in Seaside OR June 6-7 and
HamCom in Irving TX June 12-13
We would greatly appreciate any booth help that any of may be able to
provide at either show.
If you are attending either show and would like to help our for a few
hours either day then please
Consider the use of an external battery pack. Starts to get complicated.
Perhaps best the way it is and up to the operator to turn the feature on
when it's required.
The menu system is very quick and easy to use with a little familiarity.
73's Peter VK4JD
-Original Message-
From:
Good idea, David. I'd like that option, too.
/Rick N6XI
On Fri, May 29, 2015 at 10:48 AM, David Anderson gm4...@yahoo.co.uk wrote:
I wonder if the Auto OFF command could be enhanced so that it has an
option so that it takes effect only if the KX3 is running from internal
batteries?
The
Hi,
I may be able to spend a pair of hours at Sea-Pac on Saturday...
Dave Cole
NK7Z
--
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
For MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
For Dopplergram information see:
Maybe you are a bit hasty with the power switch?
When the move the VFO knob, the new frequency isn't written into the
EEPROM straight away, it will only be written if the knob stays still
for a certain period, or if you change another setting like operating
mode. This is to keep the number of
Matt,
I believe what you said is correct. I was borrowing space in an electronics
lab tonight and was working quickly during the final install because others
were needing the space. I have since tried waiting (it took me about a
minute on frequency) and it is writing to EEPROM correctly. I had
Working with Craig at Elecraft, we determined that the TX noise was caused by
the MON turned on in SSB mode. I'm trying to understand what's causing the
noise. The feed back path for the monitor would have to be internal to the
DSP software. That is the mic audio A-D would have to be mixed with
I have a XG-2 for sale that I am not using I would like $75.00 shipped.This is
the three band 80/40/20 meter test oscillator/S meter calibrator.Please email
me direct as I receive the list in digest format, to skipnc9o at yahoo dot com.
Thanks, Skip NC9O
On Sat, 30 May 2015 10:34:31 -0500 James Wilson w4rk...@gmail.com
writes:
Tom,
Since you receive white noise, before you dive into
the K3, consider that there is an item that is common
to all three antenna inputs. - The BNC connector
and coax to the BudiPole.
Try another independent
Hi Rose!
Fantastic to see you here again, I know many of us fans of yours are elated!!
If you look at the picture here:
http://www.elecraft.com/K3/K3.htm
As somebody already stated it looks like a capital S but in a smaller size.
Cheers 73,
Howie - WA4PSC
Rose Kopp posted:
Have noted
Hello all:
Started building a K2 back in 2005, and had to set it aside. So now I’m back at
it after a LONG break. ☺
Anyway….
I’m at the point of first power up, and everything checks out except for one
thing: I have two (vertical) LCD segments that are not lighting up (where the
“L” would be
Jim and All,
Not sure if you were really including Dick, K4XU, in your comment about
those who are SK. Dick is very much alive and kicking, and living now in
Bend, Oregon!!! Dick is a very dedicated CW op, so you can be assured that
QSK was a big deal on his must do list.
I'm not all that
17 matches
Mail list logo