[Elecraft] K3 fixed TX audio from the monitor

Hi A long standing wish is to get fixed level audio out from the audio monitor for the K3 Some operators don't like there voice hearing and turn of the audio monitor low or off. Result is a blank or weak TX audio in the recording. See

[Elecraft] WorkAround: Keyboard Issue - QRO Dropped Characters Via P3

Issue: When sending high speed CW (around 60wpm or higher) using a keyboard connected to the P3 you may experience occasional delays and/or dropped characters. Root Cause: Unknown - Elecraft will need to investigate and remedy. Resolution: Plug your video monitor into the P3 and change the

[Elecraft] DZKit Sienna and K3

Thinking about adding another kit transceiver to the toy box. If anyone has built and operated a DZKit Sienna and would be willing to offer hands-on comparisons with the K3, please do . . . either here if you think it's of general interest, or via direct e-mail: eda...@law.du.edu. Tnx! Ted,

[Elecraft] Elecraft SSB Net

Today's Elecraft SSB net will meet at 18:00 UTC on 14.3035 +/-. I will be net control from the Atlanta suburbs. I look forward to hearing everyone on the net. 73 de, --Ian Ian Kahn, KM4IK Roswell, GA EM74ua km4ik@gmail.com mailto:km4ik@gmail.com 10-10 #74624, North Georgia

Re: [Elecraft] K3 fixed TX audio from the monitor

Use Line Out. 73, Ed W0YK On Aug 9, 2015 4:55 AM, Peter p...@pi4cc.nl wrote: Hi A long standing wish is to get fixed level audio out from the audio monitor for the K3 Some operators don't like there voice hearing and turn of the  audio monitor low or off. Result is a blank or weak 

[Elecraft] K3 Trade Offer

If you have a K3 and looking to upgrade to the K3S while wondering what to do with your K3, read on. I have a new Meade 8 LX90 ACF Telescope with field tripod, GPS and computer control Audioguide which I bought earlier this year on impulse. I have $1,600 invested but have never gone out at night

[Elecraft] KX3 and HDSDR with omni rig ... question

I am a newbie with HDSDR and omni ... I got the panaramic display working but the received signals are displayed 12 kHz off of where they should be. The frequency of the LO and KX3 tuning are displayed in the correct position on the display. Any suggestions will be appreciated. Thanks,

Re: [Elecraft] KRX3 always uses antenna from main RX

This must have been N1MM+ or I pressed RX ANT too long. I forgot that RX hold has a functionality with SUB on, switching between AUX and MAIN. It is easy to be fooled. Good that this group exists. Ignacy -- View this message in context:

[Elecraft] WorkAround: Keyboard Issue - QRO Dropped Characters Via P3

Issue: When sending high speed CW (around 60wpm or higher) using a keyboard connected to the P3 you may experience occasional delays and/or dropped characters. Root Cause: Unknown - Elecraft will need to investigate and remedy. Resolution: Plug your video monitor into the P3 and change the

[Elecraft] K3S LOCAL REMOTE

I have been working with new K3S-P3 along with the Remote Rig 1258 MKII K3 Twin system. Input received from a few on the line here so wanted to give a short report. Goal was to have both full local and remote control of the K3S-P3 with as few cable swaps as possible. I am using the W3YY FSK-CW-PTT

Re: [Elecraft] K3S Sub-Receiver: How to Hear Both Receivers?

Byron, First, it is not possible to transmit on the Sub - it is receive only. I don't know what you mean by have the signals on both the main and sub-receivers - if you turn on the SUB, you will have the main in one ear and the SubRX in the other. You can hear signals in the main RX, and

[Elecraft] TX MON for the P3

I installed two TX MON boards in my two P3's. I upgraded both K3s and both P3s. In neither P3 to I get a TX MON in the menu. I installed both P3's TX MON boards on a grounded mat and I was also grounded. So I am at a loss why there is no TX MON appearing in my P3 Menu. Any help will be

Re: [Elecraft] TX MON for the P3

You need the beta firmware upgrade for the P3. I installed two TX MON boards in my two P3's. I upgraded both K3s and both P3s. In neither P3 to I get a TX MON in the menu. I installed both P3's TX MON boards on a grounded mat and I was also grounded. So I am at a loss why there is no TX MON

Re: [Elecraft] Blank display on K3 power on

Glenn, Fire up K3 Utility and first read the HELP section on forcing a firmware load. Follow those instructions and load all firmware. If that does not work, contact K3support. 73, Don W3FPR On 8/9/2015 7:39 PM, Glenn - N5RN wrote: All - I turned on my K3 this afternoon and was greeted

Re: [Elecraft] TX MON for the P3

Did you update to the beta P3 firmware with the initial TX Mon support? From Eric 10 days ago: Yes, P3 f/w v1.5 is up on the website at: http://www.elecraft.com/software/P3/elecraft_p3_software.htm As with all of our s/w, it is a download from the site for the P3 andis not included with the

Re: [Elecraft] TX MON for the P3

Bill, What is the rev level of the firmware you loaded in the P3? Bob Nobis - N7RJN n7...@nobis.net On Aug 9, 2015, at 14:36, William Levy wgl...@gmail.com wrote: I installed two TX MON boards in my two P3's. I upgraded both K3s and both P3s. In neither P3 to I get a TX MON in the

[Elecraft] K3S Sub-Rx Antenna Choices

In my quest to learn more about sub-rx operations, I’m reading through the KRX3 antenna choices (KE7X book) and see that when installing the sub-rx, there’s a choice to make in the connection of the antenna by connecting the TMP cable to one of two places. A) to the ATU, or B) the auxiliary RF BNC

[Elecraft] K3S Sub-Receiver: How to Hear Both Receivers?

Is there a way to have the signals on both the main and sub-receivers? For example, listening to a DX operator who is running split. I would like to hear the DX on the Main, and both Listen and Transmit on the Sub. I've read and re-read a lot of pages, pressed a lot of button combinations,

Re: [Elecraft] K3S Sub-Receiver: How to Hear Both Receivers?

You don't need to do anything special except have two speakers or a stereo headset.  One output goes to left speaker and the other to the right speaker.   You can hear the difference unless you have a hearing problem.  Likewise with a stereo headset you hear one in the left ear and one in the

[Elecraft] Blank display on K3 power on

All - I turned on my K3 this afternoon and was greeted by a blank display. I found that I couldn't turn the radio off using the front panel button so I pulled the power. After plugging the power back in, I tried again. A blank display. Since I had a backup I opted to try a reset (shift

[Elecraft] Ghost reception

This has happened a few times on 20m in WAE CW contest. I can see stations calling on P3 but cannot hear. Or suddenly a station comes up calling CQ although I cannot see it on P3. After doing A/B twice, everything is normal. So it seems that for a moment K3 receives different frequency than it

[Elecraft] Elecraft SSB Net Results 8/9/15

To say band conditions today were challenging is quite the understatement. We had 18 total check-ins today, myself included. Thank yous go out to John, N6JW, and Ray, WB5JJA, for their assistance as relay stations. If you tried to check in today, but didn't make it, please keep trying. 20m is

Re: [Elecraft] Blank display on K3 power on

No wise words. But I'd try first connecting to it with the K3 Utility. Phil W7OX On 8/9/15 4:39 PM, Glenn - N5RN wrote: All - I turned on my K3 this afternoon and was greeted by a blank display. I found that I couldn't turn the radio off using the front panel button so I pulled the

Re: [Elecraft] K3S Sub-Receiver: How to Hear Both Receivers?

Byron, Perhaps you're missing the first step: you need to turn it on by tapping sub on the front panel. 73, Scott N9AA On 8/9/15 6:52 PM, Byron Peebles wrote: Is there a way to have the signals on both the main and sub-receivers? For example, listening to a DX operator who is running split.

[Elecraft] KAT500 Bypass?

When the KAT500 is in Bypass are all elements really bypassed? Or are they bypassed with compensation for the internal paths? Is there an internal bypass calibration required? 73 jim ab3cv __ Elecraft mailing list Home:

Re: [Elecraft] KAT500 Bypass?

The former. Dick, K6KR Sent from my iPhone On Aug 9, 2015, at 18:17, Jim Miller j...@jtmiller.com wrote: When the KAT500 is in Bypass are all elements really bypassed? Or are they bypassed with compensation for the internal paths? Is there an internal bypass calibration required?

Re: [Elecraft] K3S Sub-Receiver: How to Hear Both Receivers?

I think this is another un-learning experience for me, coming from a radio with two big knobs. It makes sense to reverse the way I used the VFOs in the past, so I have to learn the mechanics of quickly going split, locking the Sub, and working the VFO A DX-receive frequency. I have seen this

Re: [Elecraft] SOLVED: K3S Sub-Receiver: How to Hear Both Receivers?

Lots of great tips from list members: Thanks everyone! For me, the answer was to use B SET and tap the ANT button to get it on the antenna. Other great steps: SPEAKERS 2, SUB, etc. Luckily I just missed this one. (100)72, Byron On 08/09/2015 06:52 PM, Byron Peebles wrote: Is there a way

[Elecraft] FS: KX3/KXPA100

Decided to move to a K3 remote setup so I am selling my KX3 and KXPA100: KX3 factory assembled #4352 -MH3 microphone -KXFL3 Roofing filter -KXAT3 Tuner -Accessory cable kit KXPA100 kit #1143 -KXPACBL cable kit List for the combo is $2139 + shipping. I'll sell both for $1,700.00 plus

Re: [Elecraft] TX MON for the P3

Besides uploading the beta firmware, you might need to go into the menu settings (on the P3) to set the menu items for getting the right displays enabled. I had to do this with my TX Mon. So, read the Owner’s Manual that came with the TX Mon paying particular attention to menu settings. 73,

[Elecraft] K3 VOX by mode only?

I too would like that feature I'd like to use VOX on digital modes, but never on phone and I see no way to set it up by mode such that the gain can be set to a certain value on phone (000), but higher on digital modes. Am I correct? Yes, I know I can turn it on and off manually.

[Elecraft] Elecraft CW Net Announcement

Good Morning, Please join us this afternoon and evening. 14050 kHz at 2200z Sunday (3 PM PDT Sunday) 7045 kHz at 0100z Monday (6 PM PDT Sunday) 73, Kevin. KD5ONS - __ Elecraft mailing list Home:

Re: [Elecraft] K3 fixed TX audio from the monitor

Ed Line out has only RX fixed audio level settings. TX audio is per TX monitor setting and by operator prefference . In worse case, some one don't like any feedback in SSB and you wil find a blank recoring during TX 73 Peter, PC22 elecraft-requ...@mailman.qth.net schreef op 09/08/2015