Don't power off the KX3 by abruptly killing the power to it -- make sure you
power it off cleanly by simultaneously pressing those two buttons on the left
before switching off the power supply, otherwise the settings won't get written
to NV memory properly.
73, Matt VK2RQ
On Sun, Nov 8,
Please be aware that Murphy's Law was NOT written by Murphy, but by another guy
with the same name.
73, Mike NF4L
> On Nov 7, 2015, at 12:09 PM, Dauer, Edward wrote:
>
> Is it a necessary corollary of Murphy’s Law that a multi-band Vee that has
> been flying just fine for
Coordinating the KX3 with the KXPA100 requires setting PA Mode to ON in the
KX3’s configuration menu. I noticed recently that when the system is powered
down and later restarted, the PA Mode config had reset itself to OFF. The
cabling was not disconnected – the only intervention was shutting
Oops! Quite right. Thank you Dwight!
RG-74 is big stuff. RG-174 is the small stuff (like the TMP coaxial cables
used in the K3/K3S).
As others pointed out RG-174 has only one internal conductor. You need to
tie two lengths together for a three-conductor cable, but for a short
pigtail such as a
Not my day. The telephone cable I have is 3/16" not 3/8"!
Ron
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ron
D'Eau Claire
Sent: Sunday, November 8, 2015 10:19 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] FW: [OT] Headphone Splitter -
Yes, ECN is still cancelled. The CW SS is filling the bands.
See you all next week.
73 & GL,
Kevin. KD5ONS
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Both KPA500 Remote Client and KAT500 Remote Client have a tendency to lose
connection to their respective servers here at N6XI and have to be
commanded manually to reconnect. This happens every few hours, usually both
at the same time. My other client-server pair (PstRotatorAz) connects
Top end can adjusted to ESSB 4.0 kHZ, but what is the bottom end of the TX
bandwidth? 500 Hz? Or…?
David A., KC0XT, LA
David Ahrendts davidahren...@me.com
__
Elecraft mailing list
Home:
When you shut down the power supply before turning off the KX3, the supply
voltage drops and and the KX3 defaults to low power which means that the PA
is turned off. If you shut down the KX3 before shutting off power supply
you will not have this problem.
--
View this message in context:
The Comstock Memorial Station is contemplating replacing four of our six
K3's with K3S'. It is time for new radios with the upgraded synthesizer and
USB connections.
They are all K3-100's equipped with:
KRX3F Subreceiver
KVX3A RX Antenna Module
KFLA 500 in both receivers
KFL3A 1.8K in the main
See this app note.
http://www.elecraft.com/manual/KX3%20Tuning%20Noise%20Mod%20rev%20B3.pdf
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-tuning-noise-on-12M-tp7610099p7610120.html
Sent from the Elecraft mailing list archive at Nabble.com.
I use miniature coax for 2-conductor (center plus shield) audiopatch
cables, but you'd never fit four of them into the common plug (for
combining two stereo circuits). A better solution would be some of the
specialty miniature shielded twisted pair cable that companies like
Belden make for
Whoops, meant this to go the reflector (sorry Don!) :)
A little bit of progress maybe.
I went ahead and rewired the T-UG8 base back to the original schematic to
ensure that it was as "stock" as could be. I also noticed that the
original crystal element (under the insulating material)
13 matches
Mail list logo