Jim Rodenkirch said
"You could spend money here: https://www.dxengineering.com/parts/dxe-rtr-1;
I just happen to have an RTR1A for sale. Which is this:
https://www.dxengineering.com/search/product-line/dx-engineering-rtr-1a-receive-antenna-interfaces
I purchased it in
Thanks,
I'm assuming there is a small copy/paste artifact on the page since it shows
the date of the earlier software version, 1.67.
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dick
Dievendorff
Sent: Monday, June 13, 2016
KXPA100 firmware has been updated to revision 1.35. This revision has been
in beta for quite some time.
The (optional) KXAT100 antenna tuner may now be used with the 100-watt power
amplifier bypassed. We've received requests from customers who sometimes
would like to run QRP and would like
Hello Oli,
I experienced the same and contacted Elecraft support. They suggested re-heat
the solder of U6 and U11 in the front panel to eliminate cold solder joins.
However, my eye sight and hands are not good enough to do so. I simply leave
as it is because the LCD characters usually come
From: k7ew@hotmail.comTo: elecraft-ow...@mailman.qth.netSubject: KAT-1 and PX-3
for saleDate: Fri, 10 Jun 2016 18:44:07 + I have a KAT-1 which I built
and tested all excellent in my K-1, discovering that it already had a perfectly
good one! So this one's totally unused, in excellent
“No internal hardware changes are required to use your MH2
with the Elecraft K3. Setup consists of attaching the
microphone, enabling it using the MENU commands and
making other front-panel adjustments.
Note: The jumper blocks and 5.6 k resistor supplied with
your microphone are not used. They are
A new KAT500 firmware revision 1.75 is now available for download, see
http://www.elecraft.com/KAT500/kat500_software.htm
Beta firmware arrives in a ZIP archive file; download and extract the
firmware and release notes files into a folder on your PC, and then use the
KAT500 Utility Firmware
KX2 purchased 5/20 with KXIO2 option at Dayton. KXIO2 was not available at
Dayton to be delivered.
Anyone else in this situation receive theirs?
de Ben W4SC
__
Elecraft mailing list
Home:
Hakko 888D.
On 6/13/2016 12:00 PM, Eddy Avila wrote:
Greetings Elecraft afficiados, I'm looking for a recommendation for a soldering
station, my Weller temperature-controled station of 20 years is dying an
agonizing death and its time to upgrade!
I don't use my soldering station a lot,
Stan,
All is forgiven, you may walk with pride.
;)
73,
Gary
KA1J
K3 SN 202
K3s # 10622
> As a long time Elecraft builder and owner (K1, K2, K3, KX1, KX3,
> KXPA100, KPA100, KAT2, PX3, T1 and many options and mini-modules), I
> decided to "...take a walk on the wild side" about a year ago.
The K3 is sold, awaiting funds. Thanks for all the interest
73 Jeff kb2m
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jeff
Griffin
Sent: Sunday, June 12, 2016 9:13 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] for sale k3
I have a
Ed:
Pace ST-50 - we use them at work - can't beat 'em if you can't afford a Metcal.
The tips are integrated into the heating element and they are a breeze to
change.
They also regulate FAST.
Here's one on e-Bay for $150 (I got the same one for $100)
I like my Aoyue 937. Amazon has 'em for $59.95.
73, Mike NF4L
> On Jun 13, 2016, at 1:00 PM, Eddy Avila wrote:
>
> Greetings Elecraft afficiados, I'm looking for a recommendation for a
> soldering station, my Weller temperature-controled station of 20 years is
> dying an
The PR6 is sold. Thanks for the interest
73 Jeff kb2m
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jeff
Griffin
Sent: Monday, June 13, 2016 8:01 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] for sale PR6
I'm now asking 70$
Call tech support.
Sent from my iPhone
...nr4c. bill
> On Jun 13, 2016, at 1:09 PM, Leroy Marion wrote:
>
> Does not matter, still won't connect. Tried two Win 7 computers.
>
> -Original Message-
> From: Nr4c [mailto:n...@widomaker.com]
> Sent: Monday, June 13, 2016
Have you set all devices to 38400 baud? The P3 will force the K3 to that speed
when you turn it on.
Sent from my iPhone
...nr4c. bill
> On Jun 13, 2016, at 11:55 AM, William Levy wrote:
>
> Gentlemen,
>
> My K3 powers on the P3 and the Expert 1.3.
> Out the back of my K3
Dear Elecraft-list,
today I powered my KPA500 #1584 up and got no display on the KPA500. The
backlight is working properly but the LCD shows nothing.
The Amp is working OK, it communicates with the KPA500 Remote utility, it
communicates with the K3 and does 500 W Output as before. Only the
Does not matter, still won't connect. Tried two Win 7 computers.
-Original Message-
From: Nr4c [mailto:n...@widomaker.com]
Sent: Monday, June 13, 2016 8:35 AM
To: Leroy Marion
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Cannot connect to K3S utillity
Locate
For sale - 200Hz 5 pole CW filter, offset -0.90
Shipping worldwide, money via PayPal
Please contect me off list.
73 Jan OM2XW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Greetings Elecraft afficiados, I'm looking for a recommendation for a soldering
station, my Weller temperature-controled station of 20 years is dying an
agonizing death and its time to upgrade!
I don't use my soldering station a lot, maybe once a month and once in a while
put a kit together,
The Y splitter should go on the RS-232 input to the P3, not the K3. That
is, it should connect to the "PC" connector on the P3.
Alan N1AL
On 06/13/2016 08:55 AM, William Levy wrote:
Gentlemen,
My K3 powers on the P3 and the Expert 1.3.
Out the back of my K3 the 15 pin and 9 pin go to the
Gentlemen,
My K3 powers on the P3 and the Expert 1.3.
Out the back of my K3 the 15 pin and 9 pin go to the Expert, the 9 pin
Serial is split and goes to the P3.
When the P3 is OFF the K3 and Expert talk beautifully together. When the P3
is on the band data gets lost on the way to the Expert and
Locate RS-232 in the CONFIG menu and set it to "USB" instead of a number. This
should allow the utility to connect.
Do you have a K3S/10 or a K3S/100?
What kind of amp do you have?
Sent from my iPhone
...nr4c. bill
> On Jun 13, 2016, at 10:05 AM, Leroy Marion wrote:
>
> I
On 6/13/2016 10:05 AM, Leroy Marion wrote:
I am the proud owner of K3S SN 10823. After sleeping on it, I still cannot
get the Utility to connect.
My computer sees The radio is on COM5. I have turned off everything else
connected, the amp, tuner and P3.
Is COM5 a serial port or USB? If
I am the proud owner of K3S SN 10823. After sleeping on it, I still cannot
get the Utility to connect.
My computer sees The radio it on COM5. I have turned off everything else
connected, the amp, tuner and P3.
I need to figure this out so I can save configs, so when I goof up I can
Hi Wes,
It depends on what you want to do. If you're just interested in
programming one oscillator for a specific frequency (or the second to
the same frequency too) then the need for more documentation is
essentially zero. Trial and error works.
One nice feature is being able to control
Wes,
I too was promised that the Software would be updated. It was once since I
bought mine, to fix a serious bug that had been introduced. This was a long
time ago. However it has not had another cosmetic item fixed yet. (The window
is too tall for my tiny laptop I sometimes use).
Saying
I've had one of these since January. I am pleased with the device, but the
documentation and software leave much to be desired. Actually, they leave
everything to be desired. ARRL had the same observation in their recent review.
After seeing that and mention that there was new documentation
I'm now asking 70$ shipped
73 Jeff kb2m
I just ordered a KXV3B for my K3 so I have in excess to my need's a PR6
Preamp. It comes with supplied power and ACC connector, and also includes
the two BNC double male connectors. 100$ shipped. Paypal ok...
73 Jeff kb2m
Yes a really useful piece of kit, has many uses around the shack or in the
field. For example to do the extended temperature VFO calibration for the
KX3. It is tiny and low power, and very quick to lock on to GPS. No wait for
oven to heat up.
There are two versions, one with even lower
The price is now 1600$ or best offer
73 Jeff kb2m
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jeff
Griffin
Sent: Sunday, June 12, 2016 9:13 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] for sale k3
I have a K3/10 serial 1516, along
This is the -third- time of asking, I have no response from Elecraft on this at
all, rather disappointing given well known their excellent customer service.
-
A few weeks ago another ham in this list asked if anyone else had noticed a bug
with the way that the KX3 handles VOX when the TX
32 matches
Mail list logo