I've been testing the latest version of SDRplay RSP2 (
http://www.sdrplay.com/rsp2/.
I've been using the original SDRplay for a few months now and like the 2mhz
spectrum display using my K3's IF out and Win4K3suite.
Win4K3 (http://va2fsq.com/ ) has added support for the new release SDRPlay
RSP2
Guys, it's time to reset your LoTW Location in your logging program. I and
others are getting NPOTA credits for parks during the ARRL RTTY RU contest last
weekend. They don't count, but your location info may be wrong when uploaded to
LoTW.
Sent from my iPhone
...nr4c. bill
Hi all,
Don Minkoff, NK6A, will be giving a talk on outdoor QRP operation and Summits
on the Air (SOTA) at the Palm Springs Hamfest on Feb. 4th.
I'll be joining Don to describe some related optimizations embodied in the
Elecraft KX2.
See you there!
73,
Wayne
N6KR
Hello everyone.
It is with reluctance I have decided to sell my KX3 and PX3.
Both are in like-new condition and both were factory built.
I will sell them together or separately.
I have a 100% 500+ feedback on eBay as both a seller and a purchaser.
Here is what I am selling:
Included with
Use AFSK A mode for RTTY. DATR A can also be made to work, but
my experience with AFSK A is much better. FSK D does not use the
sound card for transmission.
Make sure your computer is producing enough output drive. On my
Mac I need to go to System Preferences -> Sound and raise the
output
Dan,
It sounds like you are doing things right.
What is the Speaker slider on the computer set to? Open the playback
controls - normally set it to about 75%. The "meter" in the computer
soundcard display will not tell you the whole story. Go to the Playback
Controls to see the slider
OT: but I am going to add a couple cpu fans to the heat sink of my
KXPA100 which will be installed under the backseat of my truck. That
will ensure a little more cooling. The seat sets down on top of the
fins so the fans will be positioned to feed from one end. The
enclosure will be drilled
Did RU this past weekend and could not get KIO3B to XMIT-Receive is fine using
MMTTY and N1MM. Ended up using my Signal Link for XMIT.
Here is what I know.
NO line in or out connections on back of radio (per earlier email I saw)
Radio control, frequency, etc. work fine-just updated firmware
USB
Hello Everyone,
I would like to know what is the maximum length of cable on a K-POD, we
can use.
The reason is that I want to use it from another room in my house...of
course the K3S is in one room, and sometimes I want to listen on the
radio...remote...with Ham Radio Deluxe.in another
Hello,
Does your K2 need a tuneup?
Have you always wanted an Elecraft? A KX1, K1, K2, K3, whatever?
I build and service them all!
See what my clients have said about my construction and service work at
http://www.eham.net/reviews/detail/6768
Photos of the popular "Twins" -- the KPA100 and
Optionally, one can replace the internal fans altogether (the heat sink
is not sufficient for passive cooling under all conditions obviously).
If your installation is static, or relatively static, you can duct
cooling air from some place where the noise is "OK" to a properly
located input.
OR,
With an adequate sized heat sink, one could build a legal-limit solid state
amplifier with no fan whatsoever, but the most Hams want physically smaller
equipment even if it requires cooling fans. It's not bad engineering. It is
good engineering coming up with a product the buyer wants.
I know
I wrote an article on fan noise including in amplifiers. See
http://www.eham.net/articles/38328.
Ignacy, NO9E
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KPA-500-Running-hot-on-20m-tp7625577p7625633.html
Sent from the Elecraft mailing list archive at Nabble.com.
Recently finished the build of my KX1 and noticed that the power output on
7 mHz is lower than on 14 mHz. The manual states that it is typically the
opposite, with 14 mHz 0.2 - 0.3W lower.
I checked the voltage across a dummy load with my scope, converting P-P to
RMS and the using the 50 ohm load
Mike,
I do a lot of RTTY and other sound card modes with my K3-KPA500
pair. I have the amp go to 70c sometimes, that is when the HIGHEST
speed fan kicks in, NOT 65c. Not a problem, many RTTY contests and
still works fine! The room ambient temp has a lot to do with the temp
of the
To eliminate problems caused by the I/Q decoding and reduce costs, KX3S will
include direct sampling.
Please post April 1st.
Ignacy, NO9E
--
View this message in context:
http://elecraft.365791.n2.nabble.com/kx3-receiver-versus-K3s-receiver-tp7625537p7625629.html
Sent from the Elecraft
Thanks Barry - K3NDM, for the assistance. Turns out WINDOWS 10 updates and not
only shut off my sound card but changed one of the com ports on my Navigator.
Goes to show that you can't assume anything will be the same after an
update.73,Bill - W0BBI
On 10/01/17 00:48, Bill Frantz wrote:
> I have installed the KIO3BUPKT in my K3 and am generally quite satisfied
> with it. During the weekend RTTY contest, I noticed that I was getting
> very low audio volumes coming into my MacIntosh when the AGC was engaged
> (both in fast and slow modes). I
18 matches
Mail list logo