Re: [Elecraft] Elecraft K-2 Question

Bill, That is not a good situation, and I have never seen that condition. Check the orientation of varactors D37 and D38. Then check the soldering of the L33 leads to the 1/8 watt resistor - you may have to use a magnifier and good lighting. Then check the soldering of all components. To find

[Elecraft] K-Pod for Sale

Little used K-Pod. Like new, no smoke, no pets. With manual and cables. $195 shipped continental US. Please reply directly to QRZ email address. K1ESE John __ Elecraft mailing list Home:

[Elecraft] DVR audio

I think RF is getting into headset. Time to try ferrite beads. Ray W8LYJ Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] Elecraft K-2 Question

A question if you please. I am assembling a K-2. At present, I am currently in the Alignment and Test section, Part II. Page 65 covers the BFO test where you use Band+ and Band- to check for BFO range.  When I press Band+, the frequency counter initially reads around 1.480 MHz and starts

[Elecraft] WTB: KFL3A-2.1K 2.1 kHz, 8-pole filter

If you have an Elecraft brand KFL3A-2.1K 2.1 kHz, 8-pole filter to sell then please email me off-the-list with your price. Paypal only. Thanks for the bandwidth here. TNX & 73, Keith WA0TXJ __ Elecraft mailing list Home:

[Elecraft] OT: W2 for sale

I have a factory built W2 with 2000w sensor for $275. Keith, KV5J Keith __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

Re: [Elecraft] Intermittent loss of power output K3

Hi Peter; It definitely had one bad FET on the LPA when it was here, I do not see in the report that it was intermittent, so I may not have looked closely for those types of failures. If you are sure it makes MW power when it is in the failure state, then it is highly likely the LPA. Inspect

Re: [Elecraft] DVR audio

On Mon, Mar 4, 2019, 6:22 AM Dave Cole (NK7Z) wrote: > Does FAST also remove the light delay in the audio? > Yes. However, with FAST enabled, you cannot hear what the speech compressor is doing. Everything you hear while transmitting is "unprocessed." 73, Bob, N6TV

Re: [Elecraft] KPA1500 Beta Utility

I have no problem with seeing output power withUtility V. 1.19.2.21 and Beta MCU 02.09 2/24/2019.Bill - W0BBI __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] DVR audio

Does FAST also remove the light delay in the audio? 73s and thanks, Dave (NK7Z) https://www.nk7z.net Award Manager, 30MDG Grid Awards ARRL Technical Specialist ARRL Volunteer Examiner ARRL OOC for Oregon On 3/3/19 7:01 PM, Bob Wilson, N6TV wrote: Check CONFIG:TX MON, to see if it is set to NOR

Re: [Elecraft] Intermittent loss of power output K3 - update

Subject: [Elecraft] Intermittent loss of power output K3 Good day Late last year, my K3 (no 6957) developed a fault. The symptoms were: 1. No power output when keying the rig 2. TX LED on when keyed, (sidetone generated in CW mode) 3. Single bar showing on the RF power meter, whatever scale, ie