LIN OUT is already set at 1. The Microphone level set and extra
attenuator steps in W7 are not active until you plug a microphone
into the MIC jack and has no effect on the K3S internal sound card whuch
shows up as its own COM device.
Hank K7HP
Message: 9
Date: Wed, 3 Apr 2019 17:29:58
Two suggestions which can probably be added in firmware for K3 and K3s:
1) Allow different audio levels for speaker and phones, such as an
attenuation applicable to either.
2) Allow (but not require) the monitor level to be controlled along
with the receiver levels.
If either is already
If in CW mode the MON function determines the level of the beep. Not
all switches generate a tone when pressed. See page 65 SW TONE for
more details. If SW TONE is set to OFF there is no tone beep generated.
73
Bob, K4TAX
On 4/4/2019 5:29 PM, John Simmons wrote:
SW Tone is on, but
Hi again,
Sorry again, I forgot to include the link to captain's message:
https://bouvetoya.org/the-official-statement-of-atlantic-tunas-captain/
ABT2TC - Knut
ab2tc wrote
> Hi all,
>
> The 3Y0I expedition ship is safely back in Cape Town, thank God. I
> apologize
> for the OT (maybe)
Hi all,
The 3Y0I expedition ship is safely back in Cape Town, thank God. I apologize
for the OT (maybe) posting and promise I will not post post any further on
the subject unless something dramatically changes (such a them setting sail
for a second foolish attempt at Bouvet this season).
AB2T -
SW Tone is on, but there is no beep when the button is pushed. Any other
suggestions on how to turn on the button beep?
-J
Cady, Fred wrote on 4/4/2019 2:18 PM:
Hi John,
The Configuration menu you want is SW TONE. Set it OFF.
Cheers,
Fred KE7X
For all KE7X Elecraft books, see
Stephen,
The pinout for the MD2 microphone is the same as the MH2 and MH4.
Bias requirement is also the same - it needs a 5.6k resistor from the AF
signal (pin 1) and either +5 or +8 volts.
The pinout matches the mic jack wiring which is shown in the K3/K3S
manual on page 13.
Download the K3
I contacted Elecraft Support as advised & Doug suggested I re-seat the
filters in the main board & the Sub Receiver.
Lo & behold,... the problem disappeared and audio from all filters is now
normal!
Thanks Doug
73 Ray G3XLG
__
I don't know whether anyone can help, but I am trying without any success
to get the MD2 microphone working with a SunSdr2 transceiver, which is able
to provide the necessary bias voltage I believe. What I am lacking, and
have not been able to find online is the original manual for the microphone
As NW8L pointed out, there are simple updates to restore proper date displays
in GPS receivers.
An update should have a release date inside the build with the associated GPS
week number when it was released. With a little coding, this will allow the
receiver to display date properly for 1024
Hi John,
The Configuration menu you want is SW TONE. Set it OFF.
Cheers,
Fred KE7X
For all KE7X Elecraft books, see www.ke7x.com.
From: elecraft-boun...@mailman.qth.net on
behalf of John Simmons
Sent: Thursday, April 4, 2019 9:53 AM
To:
I've completed my K1 RF Board, 4 Band Filter Board, and Antenna Tuner Board,
and I am now moving on to Transmitter alignment before installing the
Antenna Tuner.
I discovered the KNB1 Noise Blanker is still available and just received it.
(Thanks, Elecraft!)
1) I'm assuming I should
Check "SW TONE" in the Config menu. I think that is what you are looking
for.
On Thu, Apr 4, 2019 at 10:53 AM John Simmons
wrote:
> I have two K3s. The first one emits a beep in the speaker or headphone
> whenever a button is pushed. The second one doesn't. I can't find
> anyplace to turn the
John,
Go to CONFIG then scroll to SW BEEP. Rotate the vfo A knob for on or off
(alternates)
Martin, HS0ZED
On 04/04/2019 22:53, John Simmons wrote:
I have two K3s. The first one emits a beep in the speaker or headphone
whenever a button is pushed. The second one doesn't. I can't find
I have two K3s. The first one emits a beep in the speaker or headphone
whenever a button is pushed. The second one doesn't. I can't find
anyplace to turn the function on. Is there a button or menu setting that
I'm missing?
73
-John NI0K
15 matches
Mail list logo