Hello,
You definitely need the Referenzlock board, even for microwave or eme.
Regards
Harald
DD0VS
.-.-. --... ...-- -.. -.. - ...- ...
> Am 26.07.2019 um 22:19 schrieb Alex Malyava :
>
> Hi,
> I am upgrading my 4-yeas old K3 (not K3S) with 2M option, got the K144XV
> already.
> The
Jack
Did check that - nope not the problem
Thanks
Regards,
Mark, K1RX
> On Jul 26, 2019, at 10:54 PM, Jack Brindle wrote:
>
> Perhaps the RxAnt is selected? Easy to do, easy to miss. Done it more times
> than I care to remember.
>
> 73!
> Jack, W6FB
>
>
>> On Jul 26, 2019, at 7:42 PM,
Perhaps the RxAnt is selected? Easy to do, easy to miss. Done it more times
than I care to remember.
73!
Jack, W6FB
> On Jul 26, 2019, at 7:42 PM, Mpridesti via Elecraft
> wrote:
>
> Sorry- did not fully see the problem
>
> The receiver is not working on any band not just 40. Sounds like
Sorry- did not fully see the problem
The receiver is not working on any band not just 40. Sounds like band noise on
all bands (sounds the same on every band). Did a comparison with a second K3
to confirm the no receiver problem on all bands.
Previously found by rotating some of the tmp
Confirmed that at an early stage of the trouble shooting. No difference with
either antenna selected (only one port has an antenna).
Regards,
Mark, K1RX
> On Jul 26, 2019, at 7:28 PM, Dennis Moore wrote:
>
> Any chance you accidentally switched antennas on 40m?
>
> Dennis NJ6G
>
>> On
Any chance you accidentally switched antennas on 40m?
Dennis NJ6G
On 7/26/2019 13:21, Mpridesti via Elecraft wrote:
Although I was able get the TX running again by merely doing a small twist to
all the TMP connectors that were reachable with top cover removed and behind
the front panel,
Although I was able get the TX running again by merely doing a small twist to
all the TMP connectors that were reachable with top cover removed and behind
the front panel, unable to bring back the receiver front end on 40 m. I hear
noise and very weak signals but nothing like the normal band
Hi,
I am upgrading my 4-yeas old K3 (not K3S) with 2M option, got the K144XV
already.
The radio will be used for 2M EME...
Do I need to install that Reference Lock Board?
I am afraid so :)
Description on Elecraft website is fuzzy, something like "If you do FM only
- you dont need, it... use it
Thanks, I'll do that.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help
Check everything in CW transmit first, including the VFO frequencies at
the band edges.
Then check your SSB filter alignment (and CW too) with Spectrogram to
make certain the filter passbands are aligned correctly. The FL1 filter
for both USB and LSB must be set to OP1.
Set things properly
Oh, okay.
I honestly don't know what to look for though.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
James,
As I indicated, with the K2, the LSB used on 17 meters and below is the
same sideband as used for USB on 15 meters and above. Since the 6 meter
transceiver uses a 28 MHz IF (assuming it is an Elecraft XV50), then the
USB transmission will be the same as the LSB transmission on the
It's a K2 with a 6 meter transverter.
I'll try your suggestion after work.
Thanks.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
James,
Is this a K2 or a K3?
In the K2, the sidebands are reversed on 15 meters and above, and there
is no 6 meters in the K2.
What I am saying is that if LSB works on the lower bands, then USB
should work on 15 meters and above - if this is a K2. If it is a K3,
then ignore my responses.
It appears that USB is bad across the bands. I tried USB on 6, 10, 15,
and 20 meters.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Hello,
There is a new version of Win4K3Suite available, version 2.006. If you use
N1MM and the Spectrum broadcast from Win4K3Suite this release fixes an issue
with this configuration.
Win4K3Suite is a full featured control program for the K3/S, KX3 and KX2.
It has a built in Panadapter that works
Bryan,
Interesting. I just received my first digest from the group in a LONG time; I
thought the group died. But I got in without need for an ATT account.
Bob Krug
KA2TQV
On Thursday, July 25, 2019, 6:41 PM, Bryan Brauer
wrote:
I just tried to sign on to the Yahoo KX3 user group after not
I would second that.
Mark, WB9CIF
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Vic Rosenthal
Sent: Friday, July 26, 2019 05:21
To: Wayne Burdick
Cc: Elecraft
Subject: Re: [Elecraft] AF Limit?
I would like it. I use minimal AGC and it would be ear
Hi Gernot this does not work, the Perseus has an ExtIO.dll for HDSDR so for an
input I selected Perseus HF Receiver. However you set me along the right path.
Input mode for RX is I left Q right.
RF Front end calibration SDR on IFD output controlled by Omni-Rig (2 in my case)
Full sync in both
19 matches
Mail list logo