1 year old K4D with 100W, ATU, 2 SP4 Speakers , Inrad Desk Mic, K•POD, Custom
Cover - All 100% Mint - low hours using 99% QRP power.
$5695 All original boxes and manuals - shipped U.S. Pictures available for
seriously interested
contact Pete WK8S
Ten kilometers! Wow, that’s DX!
I know that you meant 10,000 miles, but to the global readership most ops will
read it as “10 km“ first.
73,
Kevin
Sent from my iPhone
> On Nov 10, 2023, at 11:15, Victor Rosenthal wrote:
>
> I don't have a kpa1500, but I recall someone from Elecraft
Hi Jim,
I've experienced a 10% drop in output as the finals warm up, which
doesn't ultimately make a large difference, but can be compensated if
desired (a percentage of 1 dB).
It can run legal limit on all bands; but into a SteppIR, because of the
transformer/balun in play not being
On 11/10/2023 6:27 AM, Pete Smith N4ZR wrote:
I started operating FT8 while my KPA-1500amp was out for repair. Now
it's back and raising a question:
Operating with just my K-3, set at 100 watts, I would see 100 watts
indicated on its meter through the whole 15-second FT8 transmission..
When
The duty cycle of FTx is 43.3% and may be less than RTTY or PSK
depending on the transmit:receive ratio; or long winded SSB.
I've run the KPA1500 at or near legal limit into a resonant antenna on
Ftx, for hours at a time without issues. It will warm the shack and I
suggest headphones, the
I don't have a kpa1500, but I recall someone from Elecraft saying that
since the efficiency decreases when power is reduced, backing off the power
does not reduce the heat load.
Victor 4X6GP
On Fri, Nov 10, 2023, 16:28 Pete Smith N4ZR wrote:
> I started operating FT8 while my KPA-1500amp was
Thanks Fred -
When I get time, I might just pull the radio out of the rack and
remove/reset those pins...
Yeah, in the 'olden days' (mid 80s in my case) I was a bench tech fixing
dumb terminals from airports, among other things..they were connected to
each other in a daisy-chained serial 'party
Thanks Jack. I've never used macros, and none are shown in the K3 utility,
so I don't think that's the issue. I've identified at least 4 ways to
trigger the strange behavior from the front panel, and one via CAT.
73 de W0ZF
On Wed, Nov 8, 2023 at 1:34 PM Jack Brindle wrote:
> the behavior I
I’ve been running my 1500 at 12-1300w out on FT8 when chasing rare dx, which
results in numerous cycles until I work the station I’m calling. My SWR is
always below 1.5:1, and I have no need to inject the tuner except on 160 where
I’ll lower the power as a precaution. Have had no issues with
I started operating FT8 while my KPA-1500amp was out for repair. Now
it's back and raising a question:
Operating with just my K-3, set at 100 watts, I would see 100 watts
indicated on its meter through the whole 15-second FT8 transmission..
When I drive my amp, it only needs 30 watts for
Thanks very much, Dick!
73,
Mike, K8CN
From: Dick Dievendorff
Sent: Thursday, November 9, 2023 9:20 PM
To: Michael Carter
Cc: Elecraft Reflector Reflector
Subject: Re: [Elecraft] KPA3A and 6 meter TX Gain Calibration
CAUTION: This email originated from outside
11 matches
Mail list logo