Corcom metal can filter and install it with
the furnace. I soldered the metal can of the filter to the inside of the
metal furnace housing.
Jim
W6AIM
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Chuck
Catledge
Sent: Sunday, February 28
John, beware of any furnaces (or ACs) with variable speed motors. Some are RF
quiet; some are not. There are three potential sources of RF leakage I have
personally experienced:
1) Variable speed inducer motor - this is a small motor used on higher
efficiency furnaces to provide draft air to t
chokes I have made using small cable (i.e. RG400
through RG6) use radii of 1-3 inches with the RG6 tending toward 3” and greater
due to the foam dielectric.
---
Chuck, AE4CW
From: Mel Farrer [mailto:farrerfo...@yahoo.com]
Sent: Sunday, February 07, 2016 17:54
To: Chuck Catledge ; 'Guy Ol
At hamfests around the Southeast, surplus RG400 is often found in terminated
cables (usually BNC or N) in lengths up to around 20 feet. The price I've paid
is always less than $1.00 per foot, sometimes much less. I've used it to make
dozens of RF chokes (1:1 baluns). The small size of RG400 a
If you prefer a US source of a GPSDO, you might look at this one. I have a
friend who uses this one and prefers it over the Trimble based units.
http://www.force12inc.com/products/gps-locked-precision-frequency-reference-low-jitter-gps-clock-450-hz-to-800-mhz-output.html
---
Chuck, AE4CW
-Ori
Joe, in previous communications with Elecraft support on documentation
errors, they asked that I post any future error discoveries on the general
reflector as well as copy the documentation team leader. So, I presumed a
similar approach would be appropriate here as there are a growing number of
rea
I've been exercising the firmware utility (currently 1.0.11.21) for
familiarity while awaiting my shipment and have been receiving error
messages for the last three days when attempting to check for new firmware
versions. The verbose activity log looks like this:
15:07:26 Opening connection to f
Wayne, have you considered providing better shipping protection to prevent
the toroid bending/squishing that some have reported?
>Please DO NOT adjust the turns on any of the toroids in the K3 to make
>them "look nicer" :)
--
Chuck, AE4CW
___
Elec
FYI to the K3 documentation team, the link to Rev A-2, 11/07/2007 of the K3
Programmer's Reference manual results in: "The webpage cannot be found".
--
Chuck - AE4CW
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to
Page 12 of this manual contains the following in two places near the bottom
of the page:
"Error! Reference source not found"
I believe the reference should be to Figure 4 on page 9.
--
Chuck Catledge - AE4CW
___
Elecraft mailing li
Can anyone explain the usage of the accessory connector described on owner's
manual page 13?
"FP ACC This connector (RJ-45, 6 pins) is located
on the bottom of the transceiver, near the VFO B
knob. It is used with accessory devices."
--
Chuck - AE4CW
_
make that old frog turn into a prince faster than you
think!
http://s236.photobucket.com/albums/ff151/catnip911/?action=view¤t=K3_f
ullsize_v2.jpg
--
Chuck Catledge
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber
12 matches
Mail list logo
