[Elecraft] {K-2} FS

HI Ihave afully loadedK-2/100 with KAT100 for sale. K2SB KDSP2 XV60 K160 KNB2 FDIMP, all latest firmware and mods. Includes aux bus cable and Kenwood MC 43 mic. All manuals ect. Asking 950.00 shipped UPS CONUS. Please reply off list. Thanks for reading. Phil K8MBY

[Elecraft] {K-3}2.8khz filter FS

Hi All I have for sale a KFL3A 2.8khz 8pole filter. Shipped CONUS for $80.00. Please reply off list. Phil K8MBY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] {K-3} K144XV

My original question was how to monitor 2M on the sub, while using the main for HF. I don' seem to be able to do that. Phil K8MBY The K3 with K144XV supports simultaneous 2m reception on Main and Sub. I just verified it with my radio. Set the Main rx to 2m, and then in BSET,

Re: [Elecraft] {K-3} K144XV

the manuals in preparation. I'm sure someone will correct me if I'm wrong. Hope that helps. Matt Moller KG6KSL K3 #3496 Brett Howard wrote: I too would be curious to know the answer to this one. ~Brett On Thu, 2010-03-18 at 18:58 -0400, Phillip Buckholdt wrote: Finished install of my

[Elecraft] {K-3} K144XV

Finished install of my K144XV this AM. All works OK but, when I try to use it with the sub receiever it is deaf. I have the sub set to Ant=Atu. Itried using Ant=BNC but no luck here either. Sub works fine 160-6 but not 2 meter SSB or FM. What do I have set wrong? Thanks Phil K8MBY

Re: [Elecraft] K2 - KUSB PROBLEM

Also the KIO2 is not a RS-232 port ! You need to use the proper cable. Phil K8MBY K-3 #609 and several K-2's - Original Message - From: Julian, G4ILO julian.g4...@gmail.com To: elecraft@mailman.qth.net Sent: Wednesday, January 27, 2010 6:12 AM Subject: Re: [Elecraft] K2 - KUSB

[Elecraft] K-2 S Meter calibration using a XG-2

Can anyone point me to info to calibrate the K-2 S meter using a XG-2 ? Thanks Phil K8MBY K-3609 new owner K-2 3511 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] K-2 FS

Hector, AD4C Check ur yahoo email Phil K8MBY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by:

[Elecraft] Elecraft[K-3] K144XV

Anyone installed the K144XV yet ? Comments Phil K8MBY # 609 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list

Re: [Elecraft] [MM] W2 with 0.92 FW and VHF sensor unit

My W-2 behaves in exactly the same way with the basic meter. Using the new software, it is stuck in the 2W range when using auto. I am using a IC-7000 on 2. Phil K8MBY K-3 #609 - Original Message - From: Ed-AE5FV ae...@arrl.net To: elecraft@mailman.qth.net Sent: Wednesday,

[Elecraft] W-2 Wattmeter indications

Hi all Using my W-2 set to the 200W range and my K-3 set to 100W ATU in bypass and connected to a dummy load the W2 reads 100W. IF I select AUTO the W2 reads 200W ! I only have the 200 W HF sensor. Just wondering if this normal behavior? Phil K8MBY

Re: [Elecraft] My Proposed K3 Configuration so far...

I have the KUSB cable and it works fine with several computers running Win XP SP3. The drivers on the computers work fine.I have two other Prolific USB adapters that also are OK. Phil K8MBY K-3 609 - Original Message - From: Lionel Lhermitte f6...@orange.fr To:

[Elecraft] OFF topic-DX Summit

Anyone having a problem with DX summit? Phil K8MBY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

Re: [Elecraft] OFF topic-DX Summit

To: Elecraft List elecraft@mailman.qth.net; Phillip Buckholdt k8mb...@wadsnet.com Sent: Tuesday, November 17, 2009 6:59 AM Subject: Re: [Elecraft] OFF topic-DX Summit Yes, few days ago and I was obliged to check the cluster via HB9DRV website. Today apparently no problem on my side 73's Philippe

Re: [Elecraft] [K3] K3 Auto Notch distortion

I also hear distortion with auto notch engaged, If I use manual notch there is no distortion. Phil K8MBY - Original Message - From: NZ0T n...@cox.net To: elecraft@mailman.qth.net Sent: Tuesday, November 10, 2009 7:29 PM Subject: [Elecraft] [K3] K3 Auto Notch distortion I

[Elecraft] W2 Manuals

Any chance the manuals for the W-2 will be placed on the web site soon ? Like to read them over several times before the product gets here. I had a pacemaker implant last week and sorta trapped in the house for a week and a half. Can't drive. Phil K8MBY

Re: [Elecraft] Auto-Notch Broken in 3.25 (I probably missed this)

Auto noych works fine here also. NR much inproved onSSB with only a little loss of gain. Been using 3.25 two weeks. 73 Phil - Original Message - From: Dick Roth, KA1OZ raro...@comcast.net To: Ron D'Eau Claire r...@cobi.biz Cc: 'hb9brj' hb9...@gmail.com; elecraft@mailman.qth.net

[Elecraft] 3.25 Notch

OOPs make that NOTCH. Phil __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net

[Elecraft] W2 Sensors

Anyone know the physical size of the W-2 watt meter sensors? Tn Phil __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

Re: [Elecraft] K2 Carrying Handle/Strap???

Fred I have built 3 K-2's and have used the carry handlle for the IC-706 on them. It involves drilling and tapping holes for 2 2mm screws and 4 4/40 holes for the feet if used. The number forthe handle kit is something like MB-106. 73 Phil K8MBY - Original Message -

[Elecraft] K-3 SSB AM Squelch

Hi Is there any progress in getting SSB squelch implemented ? I would like to monitor 6 meters in my KRX3 while on lower bands. I can listen to 6 meters now but have to listen to noise on the right speaker. Thanks Phil

Re: [Elecraft] K3 on FM

Hi I've been running pre beta test firmware V2.92 for about a week. I has a revision for FM devation and AM compression. I have checked into several AM nets and 6 meter repeaters and have received very good audio reports. This relase has the VFO IND feature. Do not know when it will be

Re: [Elecraft] Elecraft SSB Net on 14.316 at 1800 UTC Now ON Up to14.318

Net on 14.319 today Phil - Original Message - From: Allan Bacon baco...@yahoo.com To: elecraft@mailman.qth.net Sent: Sunday, January 25, 2009 1:08 PM Subject: [Elecraft] Elecraft SSB Net on 14.316 at 1800 UTC Now ON Up to14.318 - Original Message From: KM5Q

[Elecraft] Elecraft K-3 SSB and AM Squelch

Any word when SSB AM squelch will be available ? Tnx Phil ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

Re: [Elecraft] K3: KDVR Status

Got Mine 12/12/08 Phil # 609 - Original Message - From: David and Dianne on Comcast dhh...@comcast.net To: elecraft@mailman.qth.net Sent: Sunday, December 14, 2008 12:15 PM Subject: [Elecraft] K3: KDVR Status Hi Everyone, Has anyone with a K3 Serial Number around 370 received

[Elecraft] FS-6 Meter Preamp

Having ordered a Elecraft 6 Meter preamp, I have for sale a Down East Microwave 6MLNACK 6 meter preamp kit unbilt for $25.00 + 8.00 shipping CONUS. Please reply off list. Phil K8MBY K-3 # 609 ___ Elecraft mailing list Post to:

[Elecraft] FS 6 Meter Preamp

The 6 meter preamp has been sold. 73 Phil ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

[Elecraft] Elecraft K-2 parts

Hi All I have some left over EC-2 parts to sell. 1 top cover 1 front or rear panel 1 bottom rear cover 2 2D fastners A bunch of misc screws, lock washers and spacers. Make offer OFF list. shipping 6.00. 73 Phil K8MBY

[Elecraft] Firmware Beta 2.19

Hi All I loaded Beta 2.19 and found the audio level decreased. I had to set AF gain at 12 o'clock for good level and with Beta 2.16 was good at 9 o'clock so, I went back to V 2.16 since most of the other changes were for the sub receiver. Any one else notice this ? Phil K8MBY # 609

Re: [Elecraft] Firmware Beta 2.19

] To: Phillip Buckholdt [EMAIL PROTECTED] Cc: Elecraft List elecraft@mailman.qth.net Sent: Wednesday, July 23, 2008 1:17 PM Subject: Re: [Elecraft] Firmware Beta 2.19 Phil, I don't notice a change in the audio level on my K3. Is there a possibility that you had your AGC set for strong AGC action

[Elecraft] FS K-2 and KAF2

Hi All K-2 # 5423 and the KAF2 have been sold. Thanks to all who replied. Phil K-3 # 609 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

[Elecraft] FS K-2

Hi all Having sols my KPA100/KAT2100 and my XV-5-,144 and 432, I have for sale: KAF2 built and aligned at 600hz 25.00 = shipping. Top cover, front panel and 1 bottom plate for a EC-2 + a couple 2D fastners. 10.00 + shipping. K-2 # 5423 with the following: KAT2, KIO2, KDSP2, KSSB2, KNB2,

Re: [Elecraft] Re: K3 Mystery Part

Sounds like one of the feet for a XV series transverter. Phil - Original Message - From: Brad Johnson [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Saturday, July 05, 2008 10:17 AM Subject: [Elecraft] Re: K3 Mystery Part I've received several responses regarding the

[Elecraft] K-3/100 FS

Hi All Due to health problems I am seling K-3 100 #609. This rig has the 13khz, 6khz, 2.7 khz ans 500hz filters installed. also includes: KAT3, KBPF3, KXV3, KTCXO3 and KUSB The latest Firmware (v2.02) is installed and works excellent. Includes power cable, all manuals. Shipped,

Re: [Elecraft] K3: 6M SSB audio hash

Do you have anything plugged into the rear headphone jack ? I have a pair oof Bose powered speakers plugged in and at higher power levels, I get severe RFI, . With the same speakers on my K-2/100 or my IC-7000 I have no trouble. When I had a IC-746 I had no RFI in the speakers. Just a

[Elecraft] K-3 6 Meter FM

Hi all Must be overlooking something. I am trying to get my K-3 to TX on a 6 meter repeater. I have saved 53.170 to memory with a 1 mhz minus offset and I get a ERR TXF error. What am I missing? Phil K8MBY #609 ___ Elecraft mailing list

[Elecraft] FS: KPA100 KAT100

The XV-50 has been sold. The KPA100 and KAT100 in EC-2 case still available. Phil K8MBY K-3 609 K-25423 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change,

[Elecraft] FS KPA-100 XV-50

Having rec my K-3, I am selling a KPA-100 KAT-100 in a EC-2 case with interconnect cable, manuals power cable. 100% working order, $475.00. XV-50 transverter with xtal oven $225.00 Repley off list to [EMAIL PROTECTED] Prices plus shipping in conus. Phil K8MBY

[Elecraft] K-3 Rec

Hi All K-3 #609 has arrived. Got Katiegram on 3-12-08 that shipping in abt 2 to 3 weeks. K-3 was on the porch on 3-17 -08. This was ordered on 9-04-07. Now ready to install front panel assy this PM after work(still working at 74, pays for K-3's). 73 Phil K8MBY

[Elecraft] FS: KPA100 KAT100 in tilt EC2 case

Hi I have a KPA100 and KAT100 in a EC2 case with tilt stand, for sale. Built in May 2007 and used by me. Will ship CONUS for 525.00, Also have a KAF2 for 45.00, setup for 600hz. Please contact off list at [EMAIL PROTECTED] Tnx Phil Note: This e-mail message passed through the Wadsnet

[Elecraft] K-3 XV Transverters

Tnx Tim And Jeff. About what I had figured but, I had pin 4 included. Maybe Elecraft will include this in the Owners manual later (after every one catches their breath). 73 Phil Note: This e-mail message passed through the Wadsnet outbound Mail Vault anti-virus/anti-SPAM scanners.

[Elecraft] XV transverters and the K-3

Hi Waiting on my K-3 and thought I'd make a cable for my XV-144 XV-432 to connect to my K-3. The info is very sparse. Nothing in the K-3 Owners Manual except a pin out chart and nothing in the XV manuals refering to the K-3. I have the 15 and 9 pin plugs. Need info on wiring the 15 pin end.

[Elecraft] test

Not rec any postings since 10/9. Checkd with my ISP and they say problem is with QTH.net Phil ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub,

Re: [Elecraft] K3 status update is not the same as when willitship

Notice the web status page says week of October 8th. Still waiting too Phil K8MBY - Original Message - From: Stan Rife [EMAIL PROTECTED] To: elecraft@mailman.qth.net Sent: Sunday, October 07, 2007 1:52 PM Subject: RE: [Elecraft] K3 status update is not the same as when

[Elecraft] Transverters setup

Hi all I am using a XV-50 and XV-144. I am now finishing a Xv-432. When setting up in the K-2 menu as TRN3, setting the operating freq. as 432 and exiting the menu, then going to TRN3 the dispayed frequency is 418.000. To get the K-2 display to read 432.000, I have to set the Freq. to

Re: [Elecraft] S meters in the USA

How about bringing back the 6U5 Tuning eye. - Original Message - From: Geoffrey Mackenzie-Kennedy [EMAIL PROTECTED] To: DOUGLAS ZWIEBEL [EMAIL PROTECTED] Cc: Elecraft Discussion List elecraft@mailman.qth.net Sent: Thursday, May 17, 2007 6:32 AM Subject: Re: [Elecraft] S meters in the

[Elecraft] XV-144--Not switching to TX

Hi all With all the traffic abt the K-3, I think my help request got lost. So far, have spent 3 days trying to get this silly thing to work. Had a problem at the start of alignment. K5 was energized all the time in the tx mode. Redid some solder connections on the front panel board and

[Elecraft] XV-144 Aligment

Hi All I am building a XV-144. Got to alignent and testing, LNA Bias. Adj R-13-No voltage at TP 2. voltage at r12 =0 Checked resistance to gnd With DMM at R-12 249 ohms at D3 145 ohms at junction of R15 C2-103 ohms Reversing the probes I have the same readings. A bad Q3 ? Maybe some one

[Elecraft] Toroid core T80-0

Hi All I'm building a KAT100-2. One of the toroid cores i rec was broken in half. Can I super glue it together an use it? )r, should I order another one? The core is T80-0. Phil K8MBY #5442 ___ Elecraft mailing list Post to:

[Elecraft] Oak Hills WM-1

Paul Send Me ur Email And I'll Send instructions Direct. Phil K8MBY [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

[Elecraft] Proset

Hi; I have a Heil Proset that I got from Elecraft. I hooked up according to spec sheet, jumpers on all pins on the header and 5.6k res pins 1 to6 on mic socket. This works fine if I key the K-2 with my straight key. I have a Heil foot switch I use with my IC-746 and Heil ICM. I ordered a

[Elecraft] Power Pole connectors

Hi All I am finishing a XV-50 transverter. Down to making the power cord. How is it supposed to plug on to the XV-50?? have 2 red and 2 black connectors and 4 crimp pins. I had no problem mounting the PCB connectors. H ow are they supposed to plug together since these are the sane size? I

[Elecraft] Power pole

Thanks to all who responded Don, Tom, Jim and John. THE LIGHT CAME ON!! The pictures did it. Thanks for the assist. 73 de Phil ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list.

[Elecraft] Rework stuff

H i; Maybe some one can help. I am building K-2 # 5423 with the rework eliminators. I got the unmdules and missing parts but the instructions were not good for installing missing parts. I figured it all out except the 60 meter module. I installed D-19 and 20 before testing and alignment part

[Elecraft] Toroids

Thank the Lord fo Mychael's toroids! #5423 almost to 40 meter testing. After 2 Cataract surgeries and lasar work on my left eye due to diabetic problems, I am working on number 3 K-2. Having built # 2442 and # 1030 (or was it 1031) and winding all the toroids myself. Just installed T5, T6

[Elecraft] K-2 #5423

Hi All: Just completed alignment test Part I but, have one glitch. The 5th digit in the display, the top and bottom segment do not light. All other segments change OK. I have checked and reworked all pins on the display and solder joints seem fine. All pins on the display driver are