My K3 has 2.8 and 2.1 8 pole filters in both main and sub receivers. Set up
for zero offset per manual. When I switch to 2.1 filter, I need to use the
Shift control to make receive audio sound approx normal. Perhaps 3/4 khz
shift. Is this normal? When using the 2.8 filters, no shift is
I am running K3 remotely using TRX Manager. When in the 2.8 filter the shift
display is centered on the TRX display, and display below shows 2800. When
switching to 2.1, the shift display is still centered. I did notice that
the width control slider moves up (by itself), and width display at
Don, I'm running K3 via TRX Manager, and I don't have a HI cut control From
what I see, only have XFIL, Shift, and Width controls. Don't see a Hi/Lo
command set in programmers guide, either.
John.
--
View this message in context:
More re TRX Manager - the referenced window is NOT the main control screens
for the K3. There are two screens with virtually every command included in
the programmer's guide. Can't speak for other radios, but the K3
implementation is splendid. Re my note just above, I don't even see a Hi/Lo
I have put an inquiry into Laurent at TRX Manager. I think everyone that
uses his product has found him to be very responsive to suggestions. I was
a bit put-off by the implication that my initial inquiry on this topic was
only due to resistance in using the K3 features. Not easy to do when
John, the buttons I have below the shift and width sliders are and N, and
below them are I/II and /. Are these the buttons you mean?
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Need-to-shift-8-pole-2-1-filter-tp6273972p6275123.html
Sent from the Elecraft mailing list
Just found it Never knew the slider/width caption was also a button.
Thanks a bunch!
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Need-to-shift-8-pole-2-1-filter-tp6273972p6275127.html
Sent from the Elecraft mailing list archive at Nabble.com.
I have been using my K3 remotely for several months now. Two requests
regarding remote commands.
(1) There is no VOX delay command. Using Vox remotely, what is good for
normal QSO talking is too slow for DX or Contesting. Would really like a
software command to be able to change delay.
(2) BG
Yes, you are correct. But this requires being at the radio to turn the knob.
I am running K3 remotely, and according to programmer's guide, there is no
command to do this via software.John.
--
View this message in context:
Excellent! Thanks Wayne.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-VOX-delay-BG-command-tp6238497p6239211.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home:
Not sure if I should post this question here or on the TRX Manager forum.
I was operating my K3 remotely, using TRX Manager, in the just finished ARRL
DX contest. Was operating 20 meters SSB. Last evening after contest I
looked at my email and saw several from hams who heard me on 14027 (CW
Thanks for both comments. I am very embarrassed by this, and want to make
sure I don't do it again!!
I do have the sub receiver, which as far as I know was off during that time
(not really sure of anything right now). My last contest contact was at
1405, next was 1538. During that time I did
I should have listed my call.
John Raydo, KØIZ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Operated-K3-SSB-in-CW-band-not-sure-why-tp6097259p6098503.html
Sent from the Elecraft mailing list archive at Nabble.com.
13 matches
Mail list logo