Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

As much as I dislike being a "me too" person, Elecraft is to me, the epitome of proper product, service and respect. If we could only make politicians in the same vein. 73, Gary KA1J > Thank you Alan!  As always Elecraft is there with the right stuff at > the right time!  THANKS AGAIN

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Thank you Alan!  As always Elecraft is there with the right stuff at the right time!  THANKS AGAIN GENTS!!! -- 73's, and thanks, Dave For software/hardware reviews see: http://www.nk7z.net For MixW support see: https://groups.yahoo.com/neo/groups/mixw/info For SSTV help see:

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Hi Paul, Firstly-- thank you for putting this on your radar!   I will rephrase-- the P3 fails to control the K3 when using some macros in sequence, due to the P3 failing to implement flow control, and the P3 overrunning the K3. End result is the same however-- the P3/K3 cluster fails to execute

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Yes, the issue is that after the P3 sends the UP7, DN7 command, etc. to the K3 it doesn't receive the new frequency back from the K3 right away. So when the #FXT1 command (go to fixed-tune mode) is executed it is based on the old K3 frequency, not the new one. Adding a delay in the

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Hi Dave, The P3 does execute the commands one after another. The problem is likely that the K3 commands take a little longer to execute and there is no waiting in the P3 for the K3 to change frequency. In other words, the P3 executes the serial commands in sequence. It gets to a K3 command

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

he single key you > used for the above macro, and poof! > > Warren, KD4Z > > > On 2/26/2016 12:48 AM, Jim Miller <j...@jtmiller.com> wrote: > > Date: Thu, 25 Feb 2016 22:43:18 -0500 > > From: Jim Miller <j...@jtmiller.com> >

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

ft Up) > > (A snapshot of this setup in the Genovation software is here: > https://dl.dropboxusercontent.com/u/24789865/Genovation_Pileup_ssb_ke > y.jpg > > Connect the Genovation keypad to the P3 and press the single key you > used for the above macro, and poof! > > Warren,

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

ion keypad to the P3 and press the single key you used for the above macro, and poof! Warren, KD4Z On 2/26/2016 12:48 AM, Jim Miller <j...@jtmiller.com> wrote: > Date: Thu, 25 Feb 2016 22:43:18 -0500 > From: Jim Miller <j...@jtmiller.com> > Cc: Elecraft Reflector <elecraft@mail

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

This change allows for the control of the P3 via the Genovation keypad. -- 73's, and thanks, Dave For software/hardware reviews see: http://www.nk7z.net For MixW support see: https://groups.yahoo.com/neo/groups/mixw/info For SSTV help see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

HI, I do not believe this corrects the macros being strung together bug which currently exists in the P3.  I hope this bug fix happens sooner than later. -- 73's, and thanks, Dave For software/hardware reviews see: http://www.nk7z.net For MixW support see:

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Will any of these changes effect the use of macros programmed into the P3 that are used to control the K3 - ala the "48 button keypad"? Bill W2BLC K-Line __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Hi Vic, As far as I know no work was done on that particular bug for this release. 73, Paul -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-v1-57-SVGA-v1-31-BETA-firmware-available-tp7614603p7614613.html Sent from the Elecraft mailing list archive at Nabble.com.

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

Jim, I'm not familiar with that macro design. I do know that this version allows intermixing of P3 and K3(s) commands within the same keyboard macro. 73, Paul -- View this message in context:

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

The bug that the p3 and svga freeze for a second or three apparently randomly still exists in the production firmware. It's particularly noticeable when operating QSK CW in a pileup. Does this version address that? Vic 4X6GP/K2VCO > On 26 Feb 2016, at 12:42 AM, Paul Saffren N6HZ

Re: [Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

So with this firmware will it be possible to do the DX on the LHS of the P3 screen and the pileup to the right and assign it to a P3 Fn key? jim ab3cv On Thu, Feb 25, 2016 at 5:42 PM, Paul Saffren N6HZ wrote: > BETA firmware packages for the P3 & SVGA are now available for

[Elecraft] P3 v1.57 / SVGA v1.31 BETA firmware available

BETA firmware packages for the P3 & SVGA are now available for download from the Elecraft website. These BETA versions contain new features as well as several bug fixes. With these versions we introduce the ability to embed P3 commands within SVGA keyboard macros. Also new is the ability to