Paul
You might like to check out this antenna idea on the Adventure Radio
Society web site:
http://www.arsqrp.com/ars/pages/back_issues/2006_text/0506_text/N7XJa.html
Looks good to me, and it's been used on 40/30/20 with a KX1.
73 Dave, G4AON
___
Tonight is the Adventure Radio Society's Tenth Anniversary Spartan Sprint.
The Sprint is two hours starting at 9 pm Eastern Daylight, 8 pm Central
Daylight, 7 pm Mountain Daylight, 6 pm Pacific Daylight. That's 0100 to 0300
UTC.
Exchange - Report, State (Province), Power as in: 559 ME 5W
Anyone know the Correct email address for the Toroid Guy?
Paul, KD3JF
Glen Burnie, MD
FM19qd (Map Grid Square)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub,
Hallo,
Ik ben op dit moment bezig met het afregelen van de KPA100.
Het gaat ergens mis met het laag doorlaatfilter in QRP mode.
Volgens mij zitten de juiste spoeltjes en C'tjes op de juiste plaats.
Wie (het liefst uit de omgeving van Amsterdam) kan mij helpen.
Normaal gesproken heb ik
Well, Babel Fish thinks he said:
I am at this moment busy with the afregelen of KPA100. It goes somewhere
wrong with the low doorlaatfilter in QRP vogue. According to me the correct
quills and C'tjes at the correct place sit.
He who (kindest from the surroundings of Amsterdam) me can help.
On 5/1/06, Paul Gates, KD3JF [EMAIL PROTECTED] wrote:
Anyone know the Correct email address for the Toroid Guy?
Website http://www.kitsandparts.com/
Email: paypal at partsandkits.com or w8diz at cinci.rr.com
Owner: Dieter Gentzow, W8DIZ
___
Elecraft
Peter Boereboom wrote:
Hallo,
Ik ben op dit moment bezig met het afregelen van de KPA100.
Het gaat ergens mis met het laag doorlaatfilter in QRP mode.
Volgens mij zitten de juiste spoeltjes en C'tjes op de juiste plaats.
Wie (het liefst uit de omgeving van Amsterdam) kan mij helpen.
Paul,
The toroid guy who winds toroids for Elecraft kits is Mychael Morohovich -
his email is: mailto:[EMAIL PROTECTED]
73,
Don W3FPR
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Paul Gates, KD3JF
Sent: Monday, May 01, 2006 11:06 AM
To:
The radio has been sold..
thanks
Tim
NZ8J
- Original Message -
From: NZ8J [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Sunday, April 30, 2006 7:30 PM
Subject: [Elecraft] FS: K2/100 (5020) with many options and extras
I have a K2/100 serial number 5020 loaded with most all
Hi Peter
I'll answer in English as it is the more common language for the reflector.
You wrote that you are in the setup/test /tuning phase of the KPA100 and
somehow have a problem with the LowPassFilter in the QRP mode. To your
opinion the inductors (toroids) and capacitors are correctly
Don,
I will drill the holes in the lower rear panel, but they will be used for
other purposes. (fixed level audio out and Transverter PTT).
It will add the possibility to use the QRP K2 with transverter and
Digimode-interface on VHF while leaving the KAT-100/KPA-100 combo at home.
(as I did
Is the coax ok?
Add or remove length from antenna. Guessing interaction
between coax antenna. This should demonstrate that pretty
quick.
What is the impedance range of auto tuner?
Don Wilhelm [EMAIL PROTECTED] wrote:
__
Paul,
A balun may or may not help. and in any case, a balun or
We have all 30 special callsigns assigned for tonight's Tenth Anniversary
Spartan Sprint. These callsigns are one by one calls (1x1), all ending in S
for Spartan Sprint. Here is the final list of the calls and the operators:
Spartan Sprint Call Operator
N1S
Finished my KAT-100-1 last night. Seems to be working FB. I get a
little RF in to it on 40m, and it causes the K2 to reset. Read the tips in
trouble shooting about how to cure that. It works fine on 40 if I cut the
power back to 5 watts or so.
Great kit. Went together quickly. Not
In message [EMAIL PROTECTED], Paul Webb
[EMAIL PROTECTED] writes
Hi All
I have been playing with my KX1 in the back yard the last week or so and
found that about 26ft of wire in the hot side of the bnc connector and about
the same to the cold side gets me a good match with the built in ATU on
Just finishing K60XV kit. Instructions say At this point only the
locations for J1 and J2 should be empty.
I find 8 holes scattered around the center of the board that are unused.
Did I miss something, or do these remain empty?
John
AB8WH
___
Murphy came to the anniversary bash. The autolog is broken. Looks like ISP
trouble. Our web guy will fix and we'll all have to resubmit :-(
I'll send out a notice when it's fixed.
Sorry.
That said, what a great Sprint. Good conditions and lots of activity and plenty
of those special
Is there a way to make the VFO A/B change modes? I know it keeps the
same mode per band... seems everything is per band if I read the
manual correctly.
Normally I keep VFO A on CW, and VFO B on SSB, on each band. Is there a
way to do this without having to switch modes manually each time I
Thanks a lot photos and movies appreciated.
At 07:41 PM 4/30/2006, John Harper wrote:
Well, disregard the last post. I found a viewer that let me use this laptop
to see what I had in the camera. Trip report is posted here:
http://www.ae5x.com/qrpttf2006.htm
John AE5X
Portable QRP:
Chris -
I don't think there is a way to do this. I have wanted to do the same
thing, but so far, no luck, Perhaps one of the future firmware
revisions will include this feature. Like you, I also prefer to have
one VFO on CW and the other on SSB. Actually, it would be very helpful
to be
I am at the point where I install the heatsink. The manual says to remove
all of the masking tape from the heatsink but I can't find any mention of
the the thin green film tape that covers the heatsink in the area that will
contact the 2 final amp transistors. Do I leave the green film on the
21 matches
Mail list logo