Aaron
Good job on the contest what more could ask for, well other than a
mono-bander at 100' 8). Some of the time you can get an idea by listening
to the op if he might take the time to work you. If he is going machine gun
style with canned CQ and only the numbers I don't even waste my time as I
I had the same. Finally I did read the release notes:
K3EXREF USERS MUST NOW ENABLE THE MODULE IN THE MENU: To do this, locate
the CONFIG:REF CAL menu entry and tap 2 to change the setting; flashes
XREF IN or XREFOUT. If you DO NOT have a K3EXREF module installed, use
the XREFOUT setting (the
Looking for a pair of audio transformers, something in the range of 600
to 2400 ohms impedance, 1:1 ratio (equal primary and secondary impedance).
These will be used to remove a ground-loop problem between my computer
and other equipment. I prefer something that will handle wide range
audio,
When I bought my first K3 I also had my FTDX-5000MP in the shack and
compared the 2 for over 4 months side by side using a YL-1000 amp with a
radio A/B button. The amp had 4 antenna inputs so was very easy to compare
both radios on an even playing field. As most all of you know the 5000 rates
just
Wonder when we will see release of an internal 6/10M pre-amp?
73
Gary
--
*Gary - VK1ZZ
Skype: Gary.VK1ZZ
http://www.qsl.net/vk1zz
Motorhome Portable
The Shack*
*Elecraft K3
P3 Panadapter
KPA500FT
KAT500FT**
*
__
Elecraft mailing list
A 4 square can be badly affected by metal (towers, masts, metal roofs). The
gain is similar but it loses front to back ratio in the affected direction.
David
G3UNA
You forgot the Gain. Forexample you can loose 2 - 3 dB gain on an
antenna due to interaction with another antenna or object
I wouldn't hold my breath.
73,
Fred/N0AZZ
K3 Ser # 6730--KX3 # 2573--K2/100 # 6470-KAT100
P3/SVGA--KPA500--KAT500--W2
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gary Gregory
Sent: Sunday, July 07, 2013 5:31 AM
To:
I'm not. But I did a post from Elecraft stating it was possible IF enough
wanted it.
I am over 'add on boxes' for now to fix a problem that should have been
done sooner, not later.
Just thinkin'
73
On 7 July 2013 20:49, Fred Smith m...@totalhighspeed.com wrote:
I wouldn't hold my breath.
Check the release notes, Stan. MCU 4.57 / DSP 2.79, 10-24-2012 state:
K3EXREF USERS MUST NOW ENABLE THE MODULE IN THE MENU: To do this, locate
the CONFIG:REF CAL menu and tap 2 to change the setting; flashes XREF IN
or XREF OUT.
73 de David G4DMP
In a recent message, Stan Gibbs
Hello,
I have had a different experience with regards to the 6M performance.
I was always told for years that the 6M performance on rx was pretty poor.
After I got a K3 recently, I found
the internal preamp to be pretty good. But, I had a DEMI 6M preamp, so I
installed it in a small die cast
It's on the order page now. Same price for any of the three pre's including the
old 6 pre, new 10 pre and new combo 6/10 preamp. $159.95 if memory serves.
On Jul 7, 2013, at 5:30 AM, Gary Gregory vk1zzg...@gmail.com wrote:
Wonder when we will see release of an internal 6/10M pre-amp?
73
Thanks, David. I never loaded 4.57 and the current notes on the Elecraft K3
firmware page don't include this item. I'll have to be more careful to read
all of the release notes for versions between that last loaded and a new
one.
This would have been a more seamless upgrade if the firmware had
Howdy Gang:
Has anyone performed the KX3 VFO Noise Mod on their KX3 yet???
If so, how well does the mod work in terms of reducing the VFO noise??
73, Joe W2KJ
I QRP, therefore I am
__
Somewhere I saw an adapter (or complete cable) to allow an ICOM PS-125 power
supply to power the K3.
Anybody remember?
73, Mike NF4L
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hi Fred,
I noticed on the specs that the preamp frequency range is 22 to 54 MHz. Have
you tried it on 12 meters?
73,
Mike K2MK
Fred Smith wrote
I received my new 6/10m preamp yesterday morning and installed it. I had
been using my IC-9100 for 6/10m as it has excellent preamps in it. There
Two that I have used with good results are “Triad TY-304P” and “Etal P-3356”.
These are quality
transformers and are readily available. Just enter the part number in your
search engine.
Radio Shack also has several available that should work just fine.
Just a note: A transformer is not
It's not internal, though.Wayne did state that that would not be feasible.
http://elecraft.365791.n2.nabble.com/K3-Combined-6-and-10mtr-preamp-td7572734.html
73,
~iain / N6ML
On Sun, Jul 7, 2013 at 6:05 AM, Jack Berry we...@yahoo.com wrote:
It's on the order page now. Same price for any
On 7/7/2013 12:10 AM, Jim Wiley wrote:
These will be used to remove a ground-loop problem between my computer
and other equipment.
You do NOT need a transformer. What you DO need is simple bonding.
http://audiosystemsgroup.com/HamInterfacing.pdf
There are two simple steps.
1) Get power
I have a perfect and pristine spiral bound copy of Fred Cady's book The
Elecraft K3, Design, Configuration, and Operation -- First Edition.
This is the original and I decided to update to the newer second edition.
I am selling for the price of $2 plus postage and handling (putting it in
Mike
Has not been enough traffic on 12m since I received it to know one way or
another.
Fred
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike K2MK
Sent: Sunday, July 07, 2013 9:16 AM
To: elecraft@mailman.qth.net
Hi all,
I just completed a KAT1 for an older K1. The tuner passes all tests but
won't tune an antenna or a dummy load. When tuning all the relays
activate but at the end I get the message r 9.9. The MCU is v1.09e. I've
very carefully gone over all solder connections looking for bridges etc.
I know that this has probably been discussed before, but just how bad is
the K3 on 6m/10m?
Hopefully, the KX3 doesn't suffer this fate as well.
It's one thing to spend another $160 on the 6m/10m preamp, but it also
requires the KXV3A at another $120.
Yes, that would also provide the ability to
Glen the internal preamp did not work on 6m. Your antennas are your largest
asset by far, wish I had them. About any radio with 6m would perform very
well with your setup but my FTDX-5000MP and Icom's spoiled me on the high
bands.
If you do a lot of weak signal work a mast mounted preamp and
Jim
The KX3 has no problems with the high bands works perfect, mine does anyway
it's just the K3 and only 6/10m with it.
73,
Fred/N0AZZ
K3 Ser # 6730--KX3 # 2573--K2/100 # 6470-KAT100
P3/SVGA--KPA500--KAT500--W2
.
-Original Message-
From: elecraft-boun...@mailman.qth.net
I think a preamp with the K3 is an absolute necessity out here in Southern
California with a small six element antenna for 6m. I use one both the PR6 and
the Collins Laboratory preamp I purchased from Dr Jack Smith. Both work great.
Btw, I have not heard before anyone on the east coast refer to
Lou,
What happens when you put a dummy load on it and attempt to do a TUNE -
what SWR does it report?
If it is still 9.9 or something else above 1.5, then you have a problem
with the K1 tuner - any chance you wound T1 in the direction opposite to
that shown in the manual?
If the dummy load
On 7/7/2013 11:10 AM, Keith Heimbold wrote:
I think a preamp with the K3 is an absolute necessity out here in Southern
California with a small six element antenna for 6m.
Whether a preamp is needed depends entirely on your own noise level, and
as another post noted, the antenna gain. With a
I have the PR6 mounted on the K3. Did successful JT65 6M moon bounce
with 11 element antenna,1000 watts, 110 foot BuryFlex coax, and
appropriate switching. So this setup worked.
I note that the specification for the PR6-10 has about 2dB more gain
than the PR6. The MDS and dynamic range
I've suddenly started getting a ERR TXG on 10m 6m on my 10w K3 (SN
5143). Trying to perform the 5W TX calibration fails when if gets to
10m. Ideas?
Thanks, and 73, Ross N4RP
--
FCC Section 97.313(a) “At all times, an amateur station must use the minimum
transmitter power necessary to carry
CNC73 is or did make a heavy know for the K1. The difference is not as
profound as the K2 and K3 knobs (I have all three). But it helps. The
CNC73 knob is absolutely wonderful on the K3.
73, Doug -- K0DXV
On 7/6/2013 2:58 PM, EricJ wrote:
I recently bought the 73CNC steel knob for the K2. I
I have encountered difficulty with the KAT100. I am pretty sure the problem
resulted from RF feedback in the shack from a Zero-Five flagpole antenna with
an unun at its base, an ugly balun with Polyphaser ground after 80 feet of coax
prior to entry into the shack, and a Balun Designs isolation
I had sent a post several days ago but don't see my post so will repost.
I have KX3 which in sn in 1100's. I sent it back for a mother board upgrade and
also a new bnc ant connector with 2 m suppression. It has worked fine until
last few days when I started getting high current warning the it
Dick,
Are you doing the component tests (C5 to C6 for example) into a dummy
load or into your antenna.
Trying that test into an antenna just adds a lot of other unknowns into
the formula - use a dummy load.
Not only that, check the dummy load and the coax going to it - if you
have an antenna
Hugh,
What is your supply voltage? If the supply voltage drops, then what you
see is normal.
73,
Don W3FPR
On 7/7/2013 7:33 PM, SouthCarolinaDolphin wrote:
I had sent a post several days ago but don't see my post so will repost.
I have KX3 which in sn in 1100's. I sent it back for a mother
Don,
Thanks for your prompt response. Yes, I reduced everything to its bare minimum
and tested it on a dry dummy load. I am sorry; I should have stated that. I
also used about different jumper cables to connect to the dummy load, all
yielding the same results on both 20 and 40. I also
Powerwerx.com can supply you with the adapter cable.
http://www.powerwerx.com/adapter-cables/
Mine is kind of short (5-6) but does the job nicely.
Ham Radio Outlet also carries them.
http://www.hamradio.com/detail.cfm?pid=H0-009646
Powerwerx
Google: HF6SOC-PP ... HF 6 PIN FEMALE SOCKET TO
I'm wondering, kinda thinking in the blind, if there might be a coil not making
contact, either a lead at the solder point, or a relay contact not good any
more..???
Have a great day,
Dale - WC7S
-Original Message-
From: richardjwilt...@aol.com
Date: Mon, 8 Jul 2013 00:09:05
To:
Every time I enter a frequency and then cycle through the modes instead of AM
it comes up AM S with LSB even though it appears to be only a distorted
version of AM. I know synchronous AM is not available on the KX3 and the KX3
isn't working like my K3's synchronous AM. If I recall any
Dick,
I figure you are using a multiband antenna. It may be presenting a very
low or very high impedance to the KAT100 on 20 meters. The solution is
to add or subtract about 1/8 wavelength of feedline to the antenna
system. On 20 meters, that would be about 8 feet of feedline.
Of course,
I'm trying to help a new K3 owner set up for RTTY using MMTTY and AFSK A. I
have a Mac, he's running Win XP.
I added a USB sound card (mic and fones) and stereo cables in and out. Win
recognizes it, and I chose it in MMTTY and Win.
Mark and space agree. Vox is on, and the vox settings should
Don,
I had been trying that to no avail. I drew up a a table with the data for all
the capacitors. After that, I decided to pull out an LDG-100pro to see what
would happened. Much to my surprise, I found out that I had been barking up
the wrong tree. The LDG responds the same way. Both
41 matches
Mail list logo