That won’t do any good. The main firmware has shut down at that point. The fan
is running because the relay is stuck, which is not something that firmware can
fix.
Call tech support.
73!
Jack, W6FB
> On Nov 25, 2019, at 7:49 PM, Eric Norris wrote:
>
> Reload the firmware.
>
> 73 Eric
Reload the firmware.
73 Eric WD6DBM
On Mon, Nov 25, 2019, 6:51 PM VK5GR wrote:
> FAN CTL = NOR
>
> FANs are idle while the amp is turned on - amp ambient temp was 27C at the
> time (it was powered up and had been idle for about 20 minutes).
>
> I then turned the amplifier off via the front
Does the mains switch on the rear panel shut the fan off?
I would next reload the firmware.
Bob, K4TAX
Sent from my iPhone
> On Nov 25, 2019, at 8:50 PM, VK5GR wrote:
>
> FAN CTL = NOR
>
> FANs are idle while the amp is turned on - amp ambient temp was 27C at the
> time (it was powered
FAN CTL = NOR
FANs are idle while the amp is turned on - amp ambient temp was 27C at the
time (it was powered up and had been idle for about 20 minutes).
I then turned the amplifier off via the front panel push button. I would
have expected the FANs to start up for about 10 seconds as they
What is the value in the menu for FAN CTL? If at NOR then the fan
should be off until the temp hits about 50º C. It will then increment
up one speed value about every 5 degrees temp increase. What is the
TEMP value showing? Should be about room temp or 22 to 25 C
73
Bob, K4TAX
On
Folks,
Has there been any further word on this fault? I have just had the same
thing happen to me and am wondering if it could be the same issue?
Regards,
Grant VK5GR
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft
A hidden feature if you you want to toggle thought ALL filter slots,
even if they are empty or not selected for the current Mode!
*Go into any config menu starting with FL (except for FLTX); (IE "FLx
BW", or "FLx FRQ" or "FLx GN" or "FLx ON")
Then while in that menu, tap 6/XFIL, and it will
If anbody has a spare KTCXO for the K3 to sell, pse let me know.
Tnx, 73 Gernot, DF5RF
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
"With just two antenna ports on the KPA1500, there are only two quickly
accessible tuning solutions per frequency if using both ports. If using only
one port and an external antenna switch, a common choice in many stations,
finding the correct tuning solutions can't be done fast enough to
I noticed the LPA was getting quite hot when running wspr at 5w for days at
time--even with 15% tx cycle. My workaround is a six-inch computer fan set
vertical on the right side of the k3, blowing quiet air on the right side
and bottom of the k3. It seems to work. I also have used a tiny 2"
This site is a handy way to check if a site is down for everyone or just for
you.
https://downforeveryoneorjustme.com/elecraft.com
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On Nov 25, 2019, at 5:53 AM, IK6QON Francesco wrote:
>
> Same story here in
I purchased one of these amps about two years ago. I expected it to require
50 to 60 watts of drive for full output but it only took half that. I was
worried about screwing up and hitting it with 100 watts from the K3 and
blowing the final transistor. I knew there was a pad on the input and I
Same story here in L'Aquila.
Il giorno lun 25 nov 2019 alle ore 14:31 IK4EWX ha
scritto:
> Don, and all the friends that answered, it is really a strange thing.
> Other italian hams friend of mine tried to connect Elecraft web site and
> all
> were unable to connect it.
> We have different
Might be a useful data point, maybe not. I just used my vpn to connect
to servers in Italy. One in Milan another in Cosenza. Both were able to
reach the Elecraft website without difficulty.
On 25/11/2019 20:30, IK4EWX wrote:
Don, and all the friends that answered, it is really a strange
Don, and all the friends that answered, it is really a strange thing.
Other italian hams friend of mine tried to connect Elecraft web site and all
were unable to connect it.
We have different internet providers, we all are unable to connect it.
I even changed the DNS (8.8.8.8...)on pc, but this
Or, perhaps, Beethoven… Schindler?
James Forsman. K7BIE
https://jrquark.smugmug.com/HamRadio
On Nov 24, 2019, at 11:41 PM, kevinr wrote:
Good Evening,
I could not find an open space to run the twenty meter net. The forty meter
net started when the CQWW contest faded away. There was QSB
Peter,
Contact Elecraft support on this issue. Sounds like poor grounding/ESD
protection. They may have a service bulletin to fix the issue.
Dave wo2x
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Peter Dougherty
Sent: Sunday, November 24, 2019 11:56 PM
To:
17 matches
Mail list logo
