Re: [Elecraft] USB monitor issue?

There's a special setting only documented in the K3 Firmware Release Notes as follows: * TX LINE OUT (MONITOR) LEVEL NOW ADJUSTABLE: In CONFIG:LIN OUT menu entry, tap '2' (REV switch) to set the "T=" level (TX monitor). Tap '2' again to return to the RX LINE OUT setting. So if you go to

Re: [Elecraft] K4 Radio Update

Linux kernel changes rarely break userspace. Kernel drivers are another matter. Internal kernel apis are always subject to change. 73 de AI6KG On Sun, Dec 6, 2020, 4:30 PM Mark Goldberg wrote: > On Sun, Dec 6, 2020 at 5:14 PM Dave Cole wrote: > > > > Hi Paul, > > > > Not to pick nits, but

[Elecraft] KX3 for sale or trade

Hey all, I have a mint condition almost new KX3 (serial in the 11xxx) with all the options that I don't use nearly enough. So I would like to turn it into something I'll use more like: Money: $1500 A partial or equal trade on a K3(S). Must be 100 watt and prefer it have the tuner. A

[Elecraft] K3 shortened dits - you can remedy this under N1MM+

"Kenwood does not have such an issue with any of their rigs" Shortening of the first element was evident in the keying tests I ran on my TS-590S. It's not an issue at 25 wpm but at 90+ wpm the first dit may be completely lost. The shortening is not present on every element, only on the

Re: [Elecraft] [K2] Odd AGC problem with K60XV installed

I’m going to set it up in the damp basement at my other QTH. That’s where I saw the problem originally. Will let you know if it comes back. > On Dec 7, 2020, at 11:43 AM, Don Wilhelm wrote: > > Bill, > > It does sound like it is fixed. Just be aware that some intermittents do > find their

Re: [Elecraft] K3 shortening CW dits

That was supposed to say *CONFIG:PTT-KEY RTS-DTR*. 73, Bob, N6TV On Mon, Dec 7, 2020 at 4:05 PM Bob Wilson, N6TV wrote: > I posted various solutions to the K3 element shortening issue about 7 > years ago. See this link on my QRZ.COM page : > >- How to get clean

Re: [Elecraft] K3 shortening CW dits

I posted various solutions to the K3 element shortening issue about 7 years ago. See this link on my QRZ.COM page : - How to get clean fast CW from an Elecraft K3 without using CW QRQ mode (post

[Elecraft] USB monitor issue?

I’ve been using RemoteTX for my remote operation for a while now. With the 7300 it worked just fine using the USB port for audio and control. I switched over to use it with my K3S and it seems to work differently in one strange annoying way. The audio coming over the USB line is constantly

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

How do you have the TX DLY set ? / Jim SM2EKM Den 2020-12-07 kl. 20:37, skrev Barry Simpson: I beg to differ. I have an original K3 dating from 2009 which I completely updated including the synthesisers. It made no difference to the shortened character issue which is still the same. It is

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

I beg to differ. I have an original K3 dating from 2009 which I completely updated including the synthesisers. It made no difference to the shortened character issue which is still the same. It is there both in QSK and semi break in modes but does not occur if transmit switching is manual

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

I have the upgraded synthesizer and still see the shortened dits. Dave Hachadorian, K6LL Yuma, AZ -Original Message- From: Joe Subich, W4TV Sent: Monday, December 7, 2020 12:03 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

The approximately 6 ms of dit shortening represents 10% of the dit length at 20 WPM. It gets progressively worse as the speed increases (20% at 40 WPM, 30% at 60 WPM, etc.). Note: this only applies to K3 models that do not have the upgraded synthesizer. For an unmodified K3 the solution(s)

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

I have the new synthesizer. Dave Hachadorian, K6LL Yuma, AZ -Original Message- From: Jim McDonald Sent: Monday, December 7, 2020 11:19 AM To: Reflector Elecraft Subject: Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+ Wasn't this problem fixed with the new

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

Wasn't this problem fixed with the new synthesizer? 73, Jim N7US -Original Message- Looking at it yesterday on the scope, a string of dits was about 40% duty cycle, or even as low as 33%, depending on how you score the rise and fall time. I did the test at 22 wpm and 44 wpm, and

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

Looking at it yesterday on the scope, a string of dits was about 40% duty cycle, or even as low as 33%, depending on how you score the rise and fall time. I did the test at 22 wpm and 44 wpm, and results were the same. Both speeds were corrected by using keying compensation = 6. Dave

[Elecraft] 40 meter SSB net, 12-6-2020

WM6P STEVE GA K3S/KPA1500 net control K8NU CARLOH K3S/KPA1500 NC0JW JIMC0 KX3 K6VWE STANMI K3S/KPA1500 K1NW BRIAN RI K3 WB9JNZ ERIC IL

Re: [Elecraft] [K2] Odd AGC problem with K60XV installed

Bill, It does sound like it is fixed.  Just be aware that some intermittents do find their way back, so knowing the symptoms you can recognize it quickly. 73, Don W3FPR On 12/6/2020 6:30 PM, Bill Coleman wrote: Don, I set the K2 up this weekend to try to reproduce this problem. Once again

[Elecraft] PFOT: request for help setting up Pi VPN/WireGuard on RPi

Pretty Far Off Topic: I too am watching the K4 thread since I've got a couple of K4s on order and see all these long time Linux users replying. I'd like to see if anybody who has direct experience with WireGuard VPN (specifically implemented in Pi VPN) on Debian might be interested in helping me

Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+

Does this become apparent only above a certain speed? I'm guessing it's not as big an issue below 30wpm or so, but would be good to know. On Sun, Dec 6, 2020 at 10:23 PM wrote: > I have never heard of this issue until your post. In DX contests, dits > sometimes disappear so we certainly to done

Re: [Elecraft] Speakers and HeadSets

On 12/7/2020 05:07, Bob KD7YZ wrote: > On 12/6/2020 21:58, Fred Jensen wrote: >> SPKR+PH Off? > > that is correct. > SPKR+PH reads "no" > > tnx reply Though after I just checked the 'Config" and was pressing Menu again, rather than the screen returning to the band I was on, I see "TERM" and no

Re: [Elecraft] Speakers and HeadSets

On 12/6/2020 21:58, Fred Jensen wrote: > SPKR+PH Off? that is correct. SPKR+PH reads "no" tnx reply > -- 73 Bob KD7YZ AMSAT LM #901 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] K4 Radio Update

Thank you Wayne, as you have a far better understanding of what is going on wIthin the K4. Paul. KB9AVO On Mon, Dec 7, 2020, 1:11 AM Dave Cole wrote: > Thanks Wayne for clearing that up... I was getting worried there... > > > > 73, and thanks, > Dave (NK7Z) > https://www.nk7z.net > ARRL