Re: [Elecraft] Allen wrench

You need to gently slide the large rubber band off the VFO A knob to access the single allen screw. The band can slide back on the knob with some slight stretching. Brian Broggie W6FVI Brian Broggie K4 Program Manager at Elecraft, Inc. Address Watsonville, CA Phone (831) 763-4211 Mobile (831)

[Elecraft] 40 meter SSB net, 11-14-21 7.280

Thanks to all checking in and especially to my relay stations that make this net a success. WM6P STEVE GA NETCONTROL K3S AE6JV BILL NH K3 K8NU CARL OH FTDX101D KE8QNF WALTER OH TS530S WB9JNZ ERIC IL FTDX101D NC0JW JIM CO KX3 W4DML DOUG TN K3 N4CY EVERET AL K4/1500 KX9RT SCOTT WI K3S AC8UC RAY OH

Re: [Elecraft] K4 allen wrench

Too sarcastic? Sorry Sent from my iPhone > On Nov 16, 2021, at 4:39 PM, Brian Broggie wrote: > > They are for the knobs (VFO A, VFO B, RIT, and Volume) > > > Brian Broggie > W6FVI > > Brian Broggie > K4 Program Manager at Elecraft, Inc. > Address Watsonville, CA > Phone (831) 763-4211 >

Re: [Elecraft] K4 allen wrench

They are for the knobs (VFO A, VFO B, RIT, and Volume) Brian Broggie W6FVI Brian Broggie K4 Program Manager at Elecraft, Inc. Address Watsonville, CA Phone (831) 763-4211 Mobile (831) 601-6983 Email br...@elecraft.com Website www.elecraft.com ‌ On Tue, Nov 16, 2021 at 1:31 PM Fredric Serota

Re: [Elecraft] K4 allen wrench

That is for tightening the little screw in your head if you ever decide to get rid of the rig. Sent from my iPhone > On Nov 16, 2021, at 4:30 PM, Fredric Serota wrote: > > While this is absolutely one fantastic radio, I cannot for the life of me > figure out what the little allen wrench is

[Elecraft] K4 allen wrench

While this is absolutely one fantastic radio, I cannot for the life of me figure out what the little allen wrench is for that comes with the radio. Any ideas? Fred Serota, K3BHX __ Elecraft mailing list Home:

Re: [Elecraft] K2 driving KPA1500

Ted, The 9 pin connector on the KIO2 is not compatible with the signals required by either amplifier.  You will be better off using only the PA Amp Keying from the K2. That Amp Keying output is not standard on the K2, but I believe Dave Van Wallaghen W8FGU is making up kits.  Send an email to

Re: [Elecraft] [K2] K2/100 - Serial Port Quit Working

Bill, Plug the ribbon cable in and do an end to end continuity test - KPA100 U4 pin 12 to Control Board U6 pin 25, And KPA100 U4 pin 11 to CB U6 pin 26.  That will check the board wiring and the ribbon cable. If all that is OK, try replacing CB U6. 73, Don W3FPR On 11/15/2021 7:28 PM, Bill

[Elecraft] K2 driving KPA1500

Has anyone been using a K2 to drive a KPA1500? I've read the KPA1500 manual and the just-released notes on using CI-V protocol transceivers, all of which seems straightforward enough, on paper. I would nonetheless appreciate hearing from someone who has done it - about unexpected issues,