I installed a 2m for the KX3 and it all appeared to set up great.
The only problem is it will not select the 2 meter antenna (antenna 2).
do I need to somehow tell radio that 2 meters is on antenna 2 .
I have read the manual and no where can I find This.
Asking before opening radio up again
The magic computer tech fixed it. Thanks for the help.
Unplugged the cable and turned all off then turned on and connected cable again
and it worked.
Thanks to all that replied.
Bill
WF9M
> On April 2, 2020 at 12:07 PM 1lasportsman 1lasportsman <1lasports...@cox.net
> mailto:
wrote:
>
>
> The utility is telling you that it is communicating with your KX3 at
> 38400 bits/sec. The KX3 has firmware revision 2.90.
> This is not an error message. It appears to be working just fine.
>
> 73!
> Jack, W6FB
>
> > >
I am trying to use the utility to see radio
I am getting this error message
KX3 MCU revision 02.90 rs232 speed 38400 bit/s
IT worked before but I get this now
any ideas the radio works fine but no utility with computer .I tried this on 2
computers same error.
Bill
WF9m
I made an adapter
I uses a flat aluminum bar with a hole drilled and tapped for the camera mount
and then another hole with dnc adapter for coax and antenna.
Make short as possible fron tripod.
Bill
WF9M
> On March 31, 2020 at 5:16 PM rwwatson mailto:richard.watson15...@gmail.com > wrote:
>
>
Don
Where do I do that?
> On February 3, 2019 at 1:09 PM Don Wilhelm mailto:donw...@embarqmail.com > wrote:
>
>
> Bill,
>
> There is not any requirement to register it with Elecraft.
>
> However, if you need to send the K3 for service, you will want to make
> sure that serial
Tied to check in for first time and here in Louisiana I was unable to hear
enough to tell what was being said.
Made one call but got no response
Bill
WF9M
> On February 3, 2019 at 10:26 AM Phil Shepard mailto:ph...@riousa.com > wrote:
>
>
> Sundays at 1800Z on 14.3035.
>
> > > On
I have used a Heil headset and the desk Heil HM12 and also a Kenwood mike all
wired for the kenwood.
they all work fine.
> On January 15, 2019 at 9:16 AM Fred Massey mailto:fhmas...@gmail.com > wrote:
>
>
> I purchased a heil headset, and I’m running into a bias problem using the
>
uses the same as a Kenwood.
I am using my Kenwood with Heil Pro Micro and it works fine.
Bill
W3WGG
> On July 25, 2018 at 8:24 AM Gary Smith wrote: > > > I have my father's Heil
> headsets and he > had an Icom adapter for it. I'm only using > Elecraft from
> now on and need an adapter > to fit
I use my Heil HM12 wired for my Kenwood and it works fine
Bill
W3WGG
> On July 7, 2018 at 11:07 AM Nr4c wrote: > > > Has anyone here provided any
> information on how to wire XXX mic to a KX3? > > We’ve all read various
> dissertations on how the mic is good/bad or just wrong for the use. > > I
How would this apply as we had the radio's on generator power?
> On June 26, 2018 at 1:08 PM Howard Hoyt wrote: > > > Buck, k4ia wrote: >
> >>Only the transmitter has to be on battery power. > >>You can run a
> computer, air-conditioner and > >>television on a generator or even mains
> power. >
11 matches
Mail list logo