Several posts on the reflector over the last few yeas regarding the ability to
set VOX per-mode across Data and SSB voice. Is this still on the wish list and
if so, what's keeping it from being implemented? There's a post from Wayne in
2009 saying it was on the list!
Please make this a
when
I’m keying? (Contacts are clean)
Thanks.
--
TJ Campie
Sent with Airmail
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Doesn't that warning go away after the first launch of the software? I
don't recall seeing it again after using the K3 software for the first time.
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
http://W0EA.us
*Because QRO is too easy (but
You do not need to run 250w on ft8
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
the You can consider the 2nd rx as a completely separate radio - unique
filters, unique dsp, etc And yes, using the SUB function on the front
panel, you can select diversity receive (2nd rx is on the same freq as your
primary VFO, receiving with a different antenna) or normal SUB (2nd rx is
on
Sabrent USB 2.0 to Serial (9-Pin)...
https://www.amazon.com/dp/B006AA04K0?ref=ppx_pop_mob_ap_share
This one works great with my k3
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I have an sdr play hooked up to the xvrt out and I'm curious what the
source of the signals are when deceiving in diversity mode.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Exactly how much signal is required to activate the subrx COR?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
Looking for a PA to upgrade a K3/10. Show me what you got!
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
http://W0EA.us
*Because QRO is too easy (but sometimes required!)*
__
Elecraft
Kind of an off topic request, but would anyone be remotely interested in a
TS-590s plus cash trade for a pretty bare bones K3/100?
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
http://W0EA.us
*Because QRO is too easy (but sometimes required!)*
Joe, what device do you use in the Microham?
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
http://W0EA.us
*Because QRO is too easy (but sometimes required!)*
__
Elecraft mailing list
Joe,
You are correct when the input device has been enumerated as a microphone
input, which is the bug. Without clearing the bug forcing windows to
enumerate it as a line in device, 100 on the slider is indeed adding gain.
However after clearing the bug, it's now enumerated as a line in device
Can we get one of these?
http://imgur.com/2lnecGL
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
http://W0EA.us
*Because QRO is too easy (but sometimes required!)*
__
Elecraft mailing
I'm regrettably selling my one prized possession, KX3 #288. My KX3 was one
of the first kits shipped during the production. The radio was built with
all the available options: ATU, Battery Charger, Roofing filter, keyer
paddle, and microphone. The 2m module is not yet available but it can be
added
I'm regrettably selling my one prized possession, KX3 #288. My KX3 was one
of the first kits shipped during the production. The radio was built with
all the available options: ATU, Battery Charger, Roofing filter, keyer
paddle, and microphone. The 2m module is not yet available but it can be
added
I made a quick video (8 min) on how to set up and use DSP Radio on a Mac with
your KX3. View it here:
http://www.youtube.com/watch?v=FPFJ-RBYN-gfeature=youtube_gdata_player
73, W0EA
TJ
QRP ARCI #14612
CW Ops #953
SKCC #4593T
Elecraft KX3 SN 288
Skill transcends power!
Everyone - thank you for watching my KX3 build! It was fun to have everyone
along for the ride. Unfortunately it won't let me put it on youtube since it is
3 hours long, but the video is viewable on ustreams website:
http://www.ustream.tv/recorded/23127348
Keep an eye out for more!
73, W0EA
Got mine!
Shipping 6/4 to 6/13
73, W0EA
TJ
QRP ARCI #14612 | CW Ops #953 | SKCC #4593T
NAQCC #3768 | Flying Pigs QRP #2254
Elecraft KX3 SN?
Because QRO is too easy
__
Elecraft mailing list
Home:
So now you have 2 SNs on your KX3? Confusing!
Assume you didn't have any show stoppers either? Looking good for 11th launch
then!
73, W0EA
TJ
QRP ARCI #14612
CW Ops #953
SKCC #4593T
Elecraft KX3 SN?
Skill transcends power!
On May 6, 2012, at 5:46 PM, Jeff Kinzli N6GQ wrote:
Hey
on assembly - except my huge fingers made the tiny parts
sometimes a challenge to put together.
The Elecraft crew was great in helping me, a joy to work with.
A blast to operate!
73 de N6GQ
On Sun, May 6, 2012 at 3:50 PM, TJ Campie tom.cam...@gmail.com wrote:
So now you have 2 SNs
Remember folks, there's a spreadsheet tracking the orders. If you put in
your information, you can help others and yourself find out where you stand
in the stack. As of today, there's been 23 factory build units delivered
with 15 in transit or ready to ship. That is only the first 34 minutes of
Folks, I just wanted to remind you all that as your orders arrive on your
doorstep, please email me or to the list of your SN and other information
so I can update the delivered orders tab. That way we can guess what our
SN will be (if that matters to anybody). Of course, if you have not
already
I posted the wrong link (anybody up for a cruise? :P)
Here is the correct link to the tracking sheet:
http://goo.gl/hqRqD
TJ W0EA
On Mon, Apr 9, 2012 at 8:20 AM, TJ Campie tom.cam...@gmail.com wrote:
Folks, I just wanted to remind you all that as your orders arrive on your
doorstep, please
I installed the 2m module + the 2m Reference option last night and I was
confused about the XV1 OF config. I went and got the Ref Cal value and did
the math in the manual and for both sections of 2m, it came out to -0.047
and -0.049. Does that sound right? Did I do it correctly?
Thanks, 73
TJ
Bruce- I tried to hit '0' but nothing happened, it just said N/A. I have
the latest firmware on the K3. I couldn't figure out what I was doing
wrong. I have no idea why it wont work like it says it should. This part
of the manual was very confusing.
TJ W0EA
Ah, I did not notice they were Beta. I will try that. I am sure I don't
have the Beta versions. Thanks Bruce.
TJ W0EA
On Fri, Jan 27, 2012 at 8:27 AM, TJ Campie tom.cam...@gmail.com wrote:
Bruce- I tried to hit '0' but nothing happened, it just said N/A. I have
the latest firmware
It has finally come time to list my beloved K2. It has served me well. My
K2 is a SN 4000+ model. It was built by Dale Parfit, W4OP. It has the
KAT2 ATU (built by me) and the KSB2 Sideband module (built by me). I will
also include the Icom hand mic that the rig is configured for. It also has
THOSE BLASTED FIELD TESTERS
In reality, the day to take orders is fairly meaningless... none of us are
going to get our new little toys until February anyway. That is going to
be the hardest part...
TJ W0EA
On Sun, Dec 11, 2011 at 4:42 PM, Wayne Burdick n...@elecraft.com wrote:
Well in light that I cannot get 4w requested power on the K3 to reach 40v
p-p, I'll try to do a full system reset and redo all of the calibration
procedures. How do I access the reset command?
TJ W0EA
__
Elecraft mailing list
Home:
I finished building a K3 for the radio club at work and I thought I'd take
the bull by the horns and attempt to improve the factory setting for the 5w
calibration on the 100w Bird watt meter I had. I couldn't get it to go up
the the point that looked like 5w on the meter regardless of how much I
so I've been using my K2 manual a LOT lately and the cover is starting to
fall off - the holes are tearing out. Anybody know of a good way to protect
it from falling off completely?
TJ W0EA
__
Elecraft mailing list
Home:
I am using a bug with my K2 and the auto detect is not working very well. I
already added a cap to the 2 diodes but it doesn't seem to do the job. Any
suggestions? I'm getting lots of extra dits and half-dits if I use the hand
mode and it will get stuck di-dah-di-dah'ing if I use the auto
and could not get the mystery behavior
to return. I have squashed the beast!
Anyway, I wonder if any others have had this problem. Hopefully this will help
as I have searched but found no other references to this issue.
73, W0EA
--
TJ Campie
So I accidentally skipped the first page of instructions then found that I
had some parts left over at the end of construction and I was missing the
header P1 or whatever, so I grabbed the connector and soldered it inonly
to find that the previous owner of my K2 had already put the female
Thought of something else I ran into last night - I did not have any 820 Ohm
resistors to install on the config connector when wiring up for my Icom HM-7
microphone so I used a 1.1k - what are the effects of using a larger value?
Should I try to find/make an 820 Ohm resistor or does it matter?
TJ
I am in the process of procuring a KSB2 - thank you for the offers.
TJ W0EA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
I'm interested in buying a K2 Sideband module, KSB2 - preferably still in
kit form. Paypal required, just got a bonus gift card from work :)
TJ W0EA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Still looking for an FT-100 knob for my K2 - anybody have an extra one on
hand? Also would accept others that are known to work...
de W0EA, TJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
How long do you think it should take to complete a KSB2 including tuning and
such? I plan on getting one at Dayton and would like to have it done in 3
or 4 evenings so I can use it when I do a SOTA activation over memorial day
weekend. (which I leave for Thursday night) So figure 4 hours a
Something seems weird with my K2 - when I put my hand near the front left of
the face the frequency of signals on the band swing around wildly (sometimes I
can get the signal to go outside of a 500 hz passband). Sometimes it settles
back down to where it was before but sometimes not. It also
for bad solder
joints?
--
TJ Campie, w0ea
On Wednesday, May 4, 2011 at 7:16 PM, Don Wilhelm wrote:
TJ,
That is indeed weird behavior for the K2. I would suspect a solder
connection problem somewhere inside the K2.
If not a solder problem --
Did you flush cut the leads below the BFO
Just got off the phone with Yaesu and they're out of stock on FT-100 knobs
and rings. She said I'd have to special order with a lead time of 4-6
weeks. Does anybody on the list have one they'd like to part with?
Thanks.
73 de W0EA
TJ
42 matches
Mail list logo