Sure, Keith. Connect the K3 RS232 port to the P3 and the P3 to your
computer.
73,
/Rick N6XI
On Fri, Apr 9, 2021 at 6:34 AM Keith Orchard via Elecraft <
elecraft@mailman.qth.net> wrote:
> I use Logger32 for logging and it has occurred to me I could connect my K3
> to my laptop to get automatic
I use Logger32 for logging and it has occurred to me I could connect my K3 to
my laptop to get automatic band-logging.
I run a K3, KPA500 & P3. Can I use the RS232 connector on the K3 to connect to
my laptop? Currently I use that connector to connect to the P3.
Help would be appreciated.
Keith
Opps, sorry. I was looking at the K3 table.
For the KX3 it would be SWT24;
Grant NQ5T
KX3 (8342)/KXPA100
> On Aug 22, 2019, at 12:16 PM, John Pierce via Elecraft
> wrote:
>
> Does anyone know what the CAT commands that allow you to switch from VFO A
> to VFO B?
>
> I have the phone
If you want to swap the contents of A and B, use SWT11;
Grant NQ5T
KX3 (8342)/KXPA100
> On Aug 22, 2019, at 12:16 PM, John Pierce via Elecraft
> wrote:
>
> Does anyone know what the CAT commands that allow you to switch from VFO A
> to VFO B?
>
> I have the phone section of a band set to
Does anyone know what the CAT commands that allow you to switch from VFO A
to VFO B?
I have the phone section of a band set to VFO A, and the CW section of that
band in VFO B. I have the filters and mode set for each section of the
band.
John, AD2F
I don't want to start an apps war, but I'd like some information so that I
can make decisions to suit my personal (RF) needs.
I've been gradually putting the new shack together and have connected the K3
to the PC using an Edgeport USB, 4 port RS232 facility. I've connected
FLDIGI directly and
I am attempting to use CAT commands to program the K3 to go into something I
call remote or local mode (using HRD with macros assigned to buttons)
Basically, remote mode switches the MIC to Line in and sets the compression
to 0. What is missing is to set PTT.
Local mode, switches MIC to front
The IC command will give you what you want. Voice VOX status is
available in bit 6 of Byte d.
Jack B, W6FB
On Nov 23, 2011, at 12:17 PM, tomb18 wrote:
I am attempting to use CAT commands to program the K3 to go into
something I
call remote or local mode (using HRD with macros assigned
: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of tomb18
Sent: Wednesday, November 23, 2011 12:18 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] CAT command of K3 VOX??
I am attempting to use CAT commands to program the K3 to go into something I
call
I thought you couldn't do that inn the k3 utility. I guess I could program a
macro and then just call this from HRD. I can't find any documentation on
HRD programming languages.
Perhaps I don't even need to switch to PTT and back. From the manual it
says that even if you VOX the PTT is active.
: Wednesday, November 23, 2011 2:52 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] CAT command of K3 VOX??
I thought you couldn't do that inn the k3 utility. I guess I could program
a macro and then just call this from HRD. I can't find any documentation on
HRD programming languages
Hello
Just received my K3 and the KUSB.
How do i connect the power amplifier (SPE 1K-FA automatic) and the PC
computer onto the K3? Everything should be via RS232 ? ACC ?
Tnx
PY2ADR - Adriano Perazio SN 4795
__
Elecraft mailing list
Hi
Is it possible to send a PTT and,or the CW keying commands to the K2 via
the RS232 port if the K2 has the KIO2 module installed . using software
such as MixW.
Jim, VE3CI
__
Elecraft mailing list
Home:
Jim,
See the K2 Programmer's Reference for all the commands that can be
sent/received via the K2 through the KIO2 interface. Keying uses the KY
command, and in SSB or RTTY mode, the TX command will set the transmit
state (pulls PTT low).
If your software application can issue those commands,
It seems to me, the ML command to get and set the Monitor Level is
not working.
MC: 03.14
Any ideas?
Tom, DL2RUM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
According to the Release Notes, this wasn't implemented until FW
release MCU 3.19 / DSP 2.17.
73, Ken K3IU
~~
Thomas Lindner wrote:
It seems to me, the ML command to get and set the Monitor Level is
not working.
MC: 03.14
Any ideas?
Tom, DL2RUM
A bit of help please. CAT was working fine for the first half of field day
and then quit. I was unable to get it to work again at Field Day.
Today, I connected the K3 to another computer and serial port and it still
doesn't work. I've confirmed the baud rate is set to 38,400 bps. The com
port
I believe I have the baud rate set to 4800 and HRD seems to work fine with
my K3.
Bruce-W8FU
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of WB4MAK
Sent: Monday, June 30, 2008 6:21 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] CAT No Longer Working
]
[mailto:[EMAIL PROTECTED] On Behalf Of Bruce McLaughlin
Sent: Monday, June 30, 2008 3:42 PM
To: 'WB4MAK'; elecraft@mailman.qth.net
Subject: RE: [Elecraft] CAT No Longer Working
I believe I have the baud rate set to 4800 and HRD seems to work fine with
my K3.
Bruce-W8FU
-Original Message
Bruce and Dick,
Thank you for your suggestions. Turns out the problem was a defective
USB/Serial Converter. All if fine now.
I guess all the dirty power, even though I had a UPS in line, got to the
converter some how. Or maybe it just quit.
Mack
WB4MAK wrote:
A bit of help please. CAT was
I was looking at the specs on the K3, and they look impressive. However, I
was wondering which CAT functionality will be included. Will it be possible
to control the pot settings (AF/RF/mic gain/NB gain, notch, passband tuning,
variable bandwidth IF filtering, etc etc) via the RS232 port? In
The word is that anything that can be done from the front panel can be
done from the computer interface.
73, doug
From: Robert Dwiggins II [EMAIL PROTECTED]
Date: Fri, 4 May 2007 18:12:35 -0500
I was looking at the specs on the K3, and they look impressive. However, I
was wondering
... In other
words, will most if not all of the rig's functionality be controllable using
a software interface such as Simon's Ham Radio Deluxe?
Ultimately, yes. Every control on the K3 is read by the same MCU that
interfaces to the serial port. There are no signals that pass through
any
23 matches
Mail list logo
