Re: [Elecraft] Elecraft K1 VFO reading

2021-12-04 Thread Mike Smith VE9AA
I can't math ! Correct my #'s below. Mike, Coreen & Corey Keswick Ridge, NB -Original Message- From: Mike Smith VE9AA [mailto:ve...@nbnet.nb.ca] Sent: December 4, 2021 2:02 PM To: 'd...@w3fpr.com'; 'Elecraft@mailman.qth.net' Subject: RE: [Elecraft] Elecraft K1 VFO reading As a fo

Re: [Elecraft] Elecraft K1 VFO reading

2021-12-04 Thread Mike Smith VE9AA
I can't math ! Correct my #'s below. Mike, Coreen & Corey Keswick Ridge, NB -Original Message- From: Mike Smith VE9AA [mailto:ve...@nbnet.nb.ca] Sent: December 4, 2021 2:02 PM To: 'd...@w3fpr.com'; 'Elecraft@mailman.qth.net' Subject: RE: [Elecraft] Elecraft K1 VFO reading As a fo

Re: [Elecraft] Elecraft K1 VFO reading

2021-12-04 Thread Mike Smith VE9AA
.com'; 'Elecraft@mailman.qth.net' Subject: RE: [Elecraft] Elecraft K1 VFO reading Thank you very much Don ! This is exactly the type of FB information I was looking for. I rec'd a few emails telling me to calibrate it, however the VFO reads right smack dab on perfect, so I didn't wish to

Re: [Elecraft] Elecraft K1 VFO reading

2021-11-26 Thread Mike Smith VE9AA
helm [mailto:d...@w3fpr.com] Sent: November 26, 2021 5:52 PM To: Mike Smith VE9AA; Elecraft@mailman.qth.net Subject: Re: [Elecraft] Elecraft K1 VFO reading Mike, The K1 must tune a bit below the low end of each band. That is to compensate for the crystals on the band board not being precision crys

Re: [Elecraft] Elecraft K1 VFO reading

2021-11-26 Thread Don Wilhelm
Mike, The K1 must tune a bit below the low end of each band.  That is to compensate for the crystals on the band board not being precision crystals - so your K1 is behaving as normal. You CAN tweak it by a small amount on ONE band (the 2nd band will change too). In your case, I would

Re: [Elecraft] Elecraft K1 VFO reading

2021-11-26 Thread Brian Hunt
I think what you are seeing is probably typical. I have a K1-4 that tunes down to 6988 and 13982 on 40 and 20 respectively. My tuning range is a little wider at 93 kHz. The Owner’s Manual has a detailed section on VFO alignment. If you didn’t get a manual with the radio you can probably

Re: [Elecraft] Elecraft K1 VFO reading

2021-11-26 Thread Louandzip via Elecraft
Mine that I built around 20 years ago tunes: 40m 6999.9 - 7088.820m 13994.2 - 14083.4 See page 28 of the manual.  The tuning range depends on the value of C2.  The range can be further adjusted by the number and spacing of turns on L1. It would be a good idea to go through a complete alignment

[Elecraft] Elecraft K1 VFO reading

2021-11-26 Thread Mike Smith VE9AA
Just bought a K1..an oldie but a goodie, I guess. NB board and 2 bands board (20/40) No tuner. So, just playing around, getting familiarized with this new-to-me little rig before transmitting or hooking it up to a real antenna and I notice: on 20m: it tunes from 13.974MHz - 14.063MHz