in
sequence.
73,
... Joe, W4TV
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Simon
Brown (HB9DRV)
Sent: Friday, May 16, 2008 12:17 AM
To: n4lq; [EMAIL PROTECTED]
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Serial Commands
Not quite - something very odd happening, I'll update the firmware over the
weekend to get to the latest revision.
Simon Brown, HB9DRV
--
From: Joe Subich, W4TV [EMAIL PROTECTED]
I'm in Dayton without my K3 and limited e-mail access but I
I'm trying to configure Mixw macros so it will send commands to select
various filters, FL2 etc
The Programmer's Reference isn't much help to me. I was able to interpet
the commands for my IC-7800 easily but this has me stumped. Can someone help
me get started by telling me the command
Steve,
Look at the FW commamd in the KIO2 Programmer's Reference.
73,
Don W3FPR
n4lq wrote:
I'm trying to configure Mixw macros so it will send commands to select
various filters, FL2 etc
The Programmer's Reference isn't much help to me. I was able to
interpet the commands for my IC-7800
-
From: Don Wilhelm [EMAIL PROTECTED]
To: n4lq [EMAIL PROTECTED]
Cc: Elecraft@mailman.qth.net
Sent: Thursday, May 15, 2008 6:01 PM
Subject: Re: [Elecraft] K3 Serial Commands?
Steve,
Look at the FW commamd in the KIO2 Programmer's Reference.
73,
Don W3FPR
n4lq wrote:
I'm trying to configure Mixw
]
To: n4lq [EMAIL PROTECTED]
Cc: Elecraft@mailman.qth.net
Sent: Thursday, May 15, 2008 6:01 PM
Subject: Re: [Elecraft] K3 Serial Commands?
Steve,
Look at the FW commamd in the KIO2 Programmer's Reference.
73,
Don W3FPR
n4lq wrote:
I'm trying to configure Mixw macros so it will send commands
Sent: Thursday, May 15, 2008 7:25 PM
Subject: Re: [Elecraft] K3 Serial Commands?
Steve,
I suggest that you read the entire Programmer's Reference paying
particular attention to the command syntax. There is more to it than
just entering the command itself. During that reading process, you
should
, 2008 7:25 PM
Subject: Re: [Elecraft] K3 Serial Commands?
Steve,
I suggest that you read the entire Programmer's Reference paying
particular attention to the command syntax. There is more to it than
just entering the command itself. During that reading process, you
should then understand GET
: [Elecraft] K3 Serial Commands?
Steve,
You did not use a ; at the end of the command when you posted the
macro that you were trying - that may be your sole problem.
The other potential problem could be that the K2 is in a
state where it
will not accept commands. Since I don't know what your
FW1,FW2,FW3,FW4,FW5
Simon Brown, HB9DRV
--
From: Don Wilhelm [EMAIL PROTECTED]
Look at the FW commamd in the KIO2 Programmer's Reference.
___
Elecraft mailing list
Post to:
FW4; Set the correct speed, I use 38,400 baud.
Not all published commands work - I will have to look at my K3 as I just
selected filter 5 and got filter 1 selected!
Simon Brown, HB9DRV
--
From: n4lq [EMAIL PROTECTED]
That didn't help. I
11 matches
Mail list logo