This shortening shows up in the ARRL tests as well.
73 Bill AE6JV
On 12/8/20 at 10:19 PM, a.dur...@msn.com (Andy Durbin) wrote:
"Kenwood does not have such an issue with any of their rigs"
Shortening of the first element was evident in the keying tests
I ran on my TS-590S. It's not an
"Hmm...I wonder if that has anything to do with break in? Just a random
thought... "
I should have stated that my TS-590S keying test was with VOX keying. Some
shortening of the first element would be expected. I have never connected the
PTT line of my Winkeyer.
73,
Andy, k3wyc
On 2020-12-08 03:19:+, Andy Durbin wrote:
>"Kenwood does not have such an issue with any of their rigs"
>
>Shortening of the first element was evident in the keying tests I ran on my
>TS-590S. It's not an issue at 25 wpm but at 90+ wpm the first dit may be
>completely lost. The shortening
"Kenwood does not have such an issue with any of their rigs"
Shortening of the first element was evident in the keying tests I ran on my
TS-590S. It's not an issue at 25 wpm but at 90+ wpm the first dit may be
completely lost. The shortening is not present on every element, only on the
How do you have the TX DLY set ?
/ Jim SM2EKM
Den 2020-12-07 kl. 20:37, skrev Barry Simpson:
I beg to differ.
I have an original K3 dating from 2009 which I completely updated including the
synthesisers. It made no difference to the shortened character issue which is
still the same.
It is
I beg to differ.
I have an original K3 dating from 2009 which I completely updated including the
synthesisers. It made no difference to the shortened character issue which is
still the same.
It is there both in QSK and semi break in modes but does not occur if transmit
switching is manual
I have the upgraded synthesizer and still see the shortened dits.
Dave Hachadorian, K6LL
Yuma, AZ
-Original Message-
From: Joe Subich, W4TV
Sent: Monday, December 7, 2020 12:03 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM
The approximately 6 ms of dit shortening represents 10% of the
dit length at 20 WPM. It gets progressively worse as the speed
increases (20% at 40 WPM, 30% at 60 WPM, etc.).
Note: this only applies to K3 models that do not have the
upgraded synthesizer.
For an unmodified K3 the solution(s)
I have the new synthesizer.
Dave Hachadorian, K6LL
Yuma, AZ
-Original Message-
From: Jim McDonald
Sent: Monday, December 7, 2020 11:19 AM
To: Reflector Elecraft
Subject: Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+
Wasn't this problem fixed with the new
Wasn't this problem fixed with the new synthesizer?
73, Jim N7US
-Original Message-
Looking at it yesterday on the scope, a string of dits was about 40% duty
cycle, or even as low as 33%, depending on how you score the rise and fall
time. I did the test at 22 wpm and 44 wpm, and
Hachadorian, K6LL
Yuma, AZ
-Original Message-
From: Dick Green
Sent: Monday, December 7, 2020 9:41 AM
To: Dave Hachadorian
Subject: Re: [Elecraft] K3 shortened dits - you can remedy this under N1MM+
First I’ve heard about this, and I’ve used K3’s since they were introduced.
Can you
Does this become apparent only above a certain speed? I'm guessing it's not
as big an issue below 30wpm or so, but would be good to know.
On Sun, Dec 6, 2020 at 10:23 PM wrote:
> I have never heard of this issue until your post. In DX contests, dits
> sometimes disappear so we certainly to done
I have never heard of this issue until your post. In DX contests, dits
sometimes disappear so we certainly to done want wimpy dits! Does this
issue also exist with the K3S? Is there a similar solution for those of us
that use Writelog?
John KK9A
Dave Hachadorian K6LL wrote:
I found out today
about it yesterday. The K3 monitor sounds
normal.
Life is too short for wimpy dits!
Dave Hachadorian, K6LL
Yuma, AZ
-Original Message-
From: Douglas Zwiebel
Sent: Sunday, December 6, 2020 6:38 PM
To: Elecraft Reflector
Subject: [Elecraft] K3 shortened dits - you can remedy this under
In N1MM+
Go to Configurer
Select WINKEY tab
Change value in the Keying Compensation window to 6
Magic
de Doug KR2Q
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
15 matches
Mail list logo
