Hi All.
Anyone have a K3 usb and Raspberry Pi 4 working on WSJT-X! for FT4 mode.
I have a K3 converted to USB
Would be interested in setup etc!
Please share or email me direct if the bandwidth is t wide!
Oh, congrats Space-X !!
Regards
Ken.. G0ORH
Sent from my iPad
I’ve always used CAT control for PTT with 100% success with all of my software
applications.That way I can switch between SSB and Data and find it not
necessary to make any radio adjustments.
Bob, K4TAX
Sent from my iPhone
> On Jan 20, 2020, at 2:41 PM, Wes wrote:
>
> So have I,
On 1/20/2020 8:55 AM, AL7CR wrote:
You might be able to use VOX.
VOX is a perfectly good way to key the radio. I've used nothing but VOX
for SSB, RTTY, and WSJT modes for at least 15 years.
73, Jim K9YC
__
Elecraft mailing list
I’ve asked the same question.
Sent from my iPhone
...nr4c. bill
> On Jan 20, 2020, at 9:13 AM, Art Suberbielle wrote:
>
> What provision has been made to send CW when operating remote with the K-4?
>
> 73,
>
> Art KZ5D
> __
>
I have watched many of Eric’s videos on YouTube about the K4 and how easy it
will be to operate remotely through its Ethernet port.
I have a rather naive question, because I’ve not seen much written about this
with other rigs.
How would you power up and power down the K4 remotely? I can’t
So have I, perhaps even longer. The only downside with Elecraft radios is that
VOX audio sampling follows the mic/line gain setting and is of course affected
by them. Without judicious setting of digital mode line level/sound card
level/WSJT "power level" settings, there is a nonsensical need
Test.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email
...and back to original K3 QSK question please.
Anybody tested it?
-
73 - Petr, OK1RP
"Apple & Elecraft freak"
B:http://ok1rp.blogspot.com
MeWe: https://bit.ly/2HGPoDx
MeWe: https://bit.ly/2FmwvDt
--
Sent from: http://elecraft.365791.n2.nabble.com/
What provision has been made to send CW when operating remote with the K-4?
73,
Art KZ5D
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Hello Kevin;
Just a note to say thanks to Brian for the relay back to you!
I am looking forward for better band conditions!
Much Regards,
Dwight
WM5F
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of kevinr
Sent: Sunday, January 19, 2020 7:32 PM
To: Elecraft
Oops, no sooner do I post this than I get payment from my ad on qth.
So sorry.
Thanks, Murphy - you never give up do you?
Rick
From: elecraft-boun...@mailman.qth.net on
behalf of Rick Stealey
Sent: Monday, January 20, 2020 3:26:47 PM
To:
I used on-rush current limiting series resistors on the 240vac input
to my 4200 volt transformer and one on the 5v filament of my 8877
amplifier. The filament drew normal 11A, so on-rush was
huge. Simple resistor-capacitor time constant timer controlled relay
to short out large 50w and 100w
I have tried but rig TX control is seriously broken for the K3 in WSJT-X on the
Pi. Online sources all point fingers at each other and I could find no
solutions. Flrig control works perfectly but NOT with WSJT-X. You might be
able to use VOX.
Be ready for a major hassle.
On Mon, Jan 20,
XV-50 transverter. Beautiful condition, with data and rf cables for your K2.
$100, plus $15 shipping.
Or $115 with free shipping (funny guy).
Rick K2XT
Prefer that you reply to k...@arrl.net
__
Elecraft mailing list
Home:
Here is the list of stations from the Sunday Net. I want to give a special
thank you to Tim KF5AHV who was portable on a pier off Galveston Texas who
provided some great relay service. Thank you Tim.
And thank you to the regular relay stations NC0JW, K!NW, N4NRW, and K05V for
your help. The
Me too.
Lee K0WA
On Mon, Jan 20, 2020, 12:45 PM Jim Brown wrote:
> On 1/20/2020 8:55 AM, AL7CR wrote:
> > You might be able to use VOX.
>
> VOX is a perfectly good way to key the radio. I've used nothing but VOX
> for SSB, RTTY, and WSJT modes for at least 15 years.
>
> 73, Jim K9YC
>
Drew AF2Z writes:
I hope there will be something for mechanical keys (straight, bug & cootie).
I worked AF2Z just tonight with his mechanical key (as SKCC K3Y/2) using my
old straight key and KX2. Still lots of mechanical CW on the bands. Use a
straight key ... no laptop, keyboard, USB
I’ve not been too concerned about the radio end.
But if I’m in a hotel room with only my laptop, other than using client
software and keyboard, how to send? I’ve not seen any USB to paddle interface
as yet.
Sent from my iPhone
...nr4c. bill
> On Jan 20, 2020, at 5:17 PM, Mike VE3YF
> I’ve not seen any USB to paddle interface as yet.
K1EL Winkeyer used on both ends of the link. With the
K1EL software, the "operator's" Winkeyer converts the
paddle closures to ASCII. The ASCII is transferred to
the remote (radio) WinKeyer where it is converted to
key closures ...
73,
I hope there will be something for mechanical keys (straight, bug & cootie).
73,
Drew
AF2Z
On 01/20/20 19:50, Joe Subich, W4TV wrote:
> I’ve not seen any USB to paddle interface as yet.
K1EL Winkeyer used on both ends of the link. With the
K1EL software, the "operator's" Winkeyer
Terry:
I am thinking "Wakeup on Lan". That feature is used in other
applications, maybe in the K4 as well.
--
*73 De Mike*
*VE3YF
_/http://www.ve3yf.com/_*
__
Elecraft mailing list
Home:
21 matches
Mail list logo
