Happy Holidays All,
Getting lousy SSB tx audio reports on K2, SN 3345. I
did the Elecraft-approved 2.6khz bandwith and using
the Heil MH2 mic.
Specifically, I get reports I don't have enough highs
in my tx audio. I use the Spectrograph program to
align filters per KSB2
On K2 receive, the audio i
Changes while tuning L34 on my K2 are very subtle.
Just barely hear L34 peak with the slug near the top
of the canis this normal?
I'm just trying to determine if the receiver on my K2
is working as it should. Signals on the K2 with the
Preamp switched in sound about the "same" as they do
on my
Don kindly helped me out a couple of years ago with my K2 (S/N 3500+) with a PA
HOT error when the K2 had been sitting off in my house, room temp about 67degs.
Lately now when I turn on K2 from a cold start the fan turns on immediately and
when I try to transmit into a 50-ohm dummy load I get
Does anyone know if the MH2 is the same mic as the MH3?
Tnx and 73
ed
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mail
My K2 audio output is 4-ohms which I drive into an 8-ohm ICOM speaker with
filters. Yes, it works OK, but I would like to match them better.
In the "olden" days I would simply use a 4-ohm to 8-ohm audio transformer, but
I can't find them anymore! Really, I've looked at all the suspect places,
in
Happy Holidays All!
I'm using FT8 into my KX3 in Data A mode but getting almost no contacts, On
the waterfall, I see a lot activity on 40m and 20m. I've followed the
advice from the KX3 manual for levels, but I still get very few
connections, like I'm not being heard. I also run k1jt WSPR mode and
Does Elecraft plan on selling a single lever paddle or KX2/3? I have the
QRPguys single lever paddle and it's ok.
tnx and 73
k6sdw
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.n
Lately, I've noticed my 3-year-old KX3 drifts a small amount, according to
the readout, in CW mode. For instance, if I set rig on 7.033.00 hit the key
and look at the readout it will say 7.033.010 and sometimes bounces back to
7.033.00
I don't remember this being a problem before. Is this normal f
Greetings hams, is the Elecraft XG1 signal generate stable enough to use to
perform a temperature compensation process on a KX3?
Thanks, 73
k6sdw
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http:
I solved my KX3 drift problem, it wasn't electrical but rather
mechanicalreading in the manual about the VFO I increased the
resistance to the knob spin and *voila* no more drift! I really like
simple solutions to problems.
Thanks to all that offered advice, much appreciated.
73
k6sdw
_
I bought used the KXPA100 with ATU. The KXPA100 puts out less than full
power on 30 and 15 meters. The other bands the KXP!00 puts out 100 watts
and a bit more.
Both thte KX3 and the KXPA100 have the latest firmware installed.
This according to the LED's on the amp and connected to an MFJ dummyl
I bought a used KXPA100 with ATU to work with my KX3 and I'm only getting
around 1/2 power on 15 meters into a 50-ohm dummyload.
Any suggestions what to look for or test?
Thanks,
Ed ~ k6sdw
__
Elecraft mailing list
Home: http://mailman.
Anyone using the MFJ-297 desk mic for a K2? My setup is compatible with ICOM
mic connector so this should mate up to my K2 FB.
Thanks and 73
ed
__
Elecraft mailing list
Home: http://mailman.qth.net/
Looking for the Elecraft KXPA100 for sale. What have you?
tnx and 73
Ed ~ k6sdw
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
I have an older Heil headset that uses the HC4 mic, will this sound ok on
my KX3?
Thanks and 73
ed
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecra
I'm thinking of changing the CW pitch on my K2 from 580hz to 650hz, maybe
700hzmy question, do I really need to realign the filters? This is what
I've read!
I'm discovering I like a higher tone rather than lower CW tone. At
67-years-old, go figure
Tnx and 73
ed
k6sdw
Thanks everyone for your sage advice.changing CW pitch sounds like a pain
to me!!
I think I'll use the RIT and see if it's worth all that trouble.
73's all
ed ~ k6sdw
From: Don Wilhelm
Sent: Monday, December 5, 2016 4:51 PM
To: Eddy
Hi Elecraft gang, any recommendations for Nimh batteries for my new KX3?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This lis
Greetings fellow kx3 ops.anyone have a suggestion for a decent-sounding
external speaker for the kx3? Actually, the built-in speaker sounds good by
itself, but I may want to "blast" CW around our RV campsite sometime.you
know, to bug the neighbors and ward off evil spirits! HI HI
tnx a
I have older Dell laptop and new KX3 and KX3-PCKT cables.
With no digital software running the following happens all the time:
When I plug green-band cable from PC phones output to KX3 mic input the KX3
goes immediately into TX mode with no modulation. I followed the KX3 manual and
I'm using D
With some expert help from the Elecraft forum, I'm up and running JT65/9 using
my new KX3.
My rig's s/n is 9403, do I still need to consider upgrading to the after-market
heatsink or the one that came with my new KX3 (9403) sufficient for most data
modes?
tnx and 73
k6sdw
ed
___
I too was having issues with the KXPD3 paddles on my KX3 dropping the dits at
times. Long story short, I took the dit side of the key apart and "cleaned" the
round barrel which makes contact with the key. and this solved the problem.
Too easy eh? Careful not to lose the very small screws and p
Guys, I'm old enuf when CW testing was required by the FCC for any license
grade. Commercial CW Ops could make really good $$$ as a shipboard
communications officer, I mean really good bucks! Much better than slinging
hamburgers at MacDonalds...wait, I'm not sure the Big Mac was available
b
Greetings all, where can I find the wiring diagram for the KX3 ACC2? I've
looked in my KX3 manual and didn't find much info.
tnx and 73
Ed ~ k6sdw
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: h
Greetings, can anyone suggest how to connect a KX3 to a non-Elecraft amp
keying circuit? I'm thinking I should use a small reed relay to do the
keying. The amp uses the typical grounding a pin on the amp to key up
amplifier.
Many thanks, 73
k6sdw~ Ed
_
Greetings again, following my KX3 manual rev C5, on pg 31 and menu key, it sez
to hold menu key and rotate vfo/b to find REF CAL
Following manual I never see REF CAL !
Any suggestions?
Tnx and 73
k6sdw
ed
__
Elecraft mailing l
Hello again, I noticed today that with my new KX3 driving into a 50-ohm dummy
load that I can set the power output to 15w on bands 80 - 20meters. However,
the remaining bands, 160, 17, 12, 10 meters the maximum power output is
12watts. And on 10w on 6 meters.
Is this normal?
Many thanks and
Me again...I'm not a hotshot CW op..16 ~ 20 wpm if I'm lucky, (you
know, going downhill with the wind behind ya). With that said, what's the
opinion of the KXPD3 key? The only review on eHam was not good.
Seems lot'sa CW ops like the Palm Pico key.
tnx and 73
ed ~ k6sdw
I just bought the KXPD3 for my new KX3
First the disclaimer.I'm not a hotshot CW op, maybe back in my novice days
as wn6sdw. Now, I'm lucky to inch towards 20wpm these days, but only when the
going downhill and the wind is at my back. And no wine.
With that said, I like this little bugger
I can't get my Windows 7 to connect to my new KX3 using the Elecraft KX3
utility software.
I bought the official USB cable from Elecraft and I have the USB mapped to COM8
on my PC and the cable plugged into ACC1.
So far, all is good.
Then I launch the KX3 software to read memory data from th
So, all is up and running thanks to Don W3FPR!! Don responded back within an
hour of my request for help getting the KX3 Utility to work. Don had a few
suggestions. Trying each one, I finally stumbled across the answer to my sad
story!
I bought the official Elecraft USB cable and downloaded th
Greetings all, I'm curious to hear from anyone using a portable HF magnetic
loop. I've read the theory behind them so I'd like to hear your opinion about
them? How efficient these antennas are, especially running qRP.
Thanks all,
73
ed
___
Has anyone sent their Heil MH2 to AB5N Bob Nagy for his upgrade? I've never
been impressed with my K2 SSB tx audio and I've done everything Elecraft has
recommended to improve the TX audio, including sending it to Gary for alignment
-- Gary did a wonderful job aligning my K2, but the K2 TX audio
My KX3 is about 2 years old, recently I set he The KXBC3 to 16hr charge
and powered down the KX3 and everything looked normal. However, a few hours
later I noticed the Lo-Supply message was flashing on and off, but when I
checked the KX3 was getting 13.61vdc and I believe charging was still
taking
Greetings Elecraft afficiados, I'm looking for a recommendation for a soldering
station, my Weller temperature-controled station of 20 years is dying an
agonizing death and its time to upgrade!
I don't use my soldering station a lot, maybe once a month and once in a while
put a kit together, s
Hello again, I've been using the Heil mic on my K2 that Elecraft sold and I've
never been satisfied with the results.
Has anyone tried other mics, such as from Kenwood for better
performancemainly more output and less bass?
Tnx and 73
ed
_
Greetings fellow K2 opsI'm looking for advice on who makes a good
G5RV antenna.I need something simple to put in the air for a few
months on HF and used with my autotuner.
thanks and 73ed
___
Elecraft mailing list
Post to: Elecra
37 matches
Mail list logo