1. Separate power supply or small control box (ala ACOM 2000A). Same
form factor as K line if separate power supply (small control box able to
control an integral or separate "KAT1500" as well).
2. Solid state.
3. Full integration with K line similar to KPA500 and easy integration
with ot
I understand Elecraft no longer sells the P3SVGA Board for the K3/K3s. I'm
looking for the board and associated cabling for a K3 if anyone has one they
would be willing to part with.
Thanks,Mike KD8RQE
__
Elecraft mailing list
Home: htt
I have wanted to learn CW and be a ham since I was 8. I started and
stopped 5 or 10 times in the next 52 years. I was finally licensed in Feb
2012
as a General and upgraded to Extra 6 months later, but I was old school
enough to not consider myself a true ham until I could do CW, so I taug
Hi,
It is written in the manual (p. 39) that:
"Roofing Filter Configuration for SSB Mode: Roofing filter FL2 (3 kHz) can be
inserted when the upper edge of the receive passband reaches either 2.4 kHz
(default value) or 2.9 kHz. When the passband edge is higher than this, FL1 is
used (wide filter).
The K3/100 switches to the KPA3A at 12 watts. So is there a 2w range
(10-12w) where the KLPA3A is putting out unacceptable IMD? Is there a way to
make the switch at 10w, or should we just avoid that 2w "danger zone"?
73
Mike KD8RQE
In a message dated 10/24/2017 10:56:38 A.M. Eastern D
Hi Jerry,
I made the decision to use a single lever paddle and not learn the
"squeeze" technique needed to run a dual lever paddle. Several reasons:
The truly high speed guys use single lever paddles--they feel they make
fewer mistakes with the single lever.
If you learn the single lever
drift off frequency while you're in a QSO.
Directions are provided for making your own.
http://www.elecraft.com/manual/E740285%20KPOD%20Owner%27s%20Manual%20Rev%20D.pdf
73, Dennis NJ6G
On 2/4/2018 03:38, Mike via Elecraft wrote:
> I seem to have misplaced the data cable that connects
I seem to have misplaced the data cable that connects the Kpod to my K3. Is
this any kind of standard cable or do I need to get a new one from Elecraft?
Thanks.
Mike KD8RQE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/
No thanks.
Mike KD8RQE
In a message dated 5/1/2017 9:51:49 A.M. Eastern Daylight Time,
va...@portcredit.net writes:
Someone did change this to OT, but it really isn't.
As others have also mentioned is that this is a list that is heavily
diluted by so many OT issues.
This is the only l
These guys have several. Well built. Not cheap. http://www.preciserf.com
Mike KD8RQE
In a message dated 5/28/2017 1:25:49 P.M. Eastern Daylight Time,
mike.ab...@gmail.com writes:
I'd like to get a directional coupler to, among other things, monitor my
transmit signal on a scope.
The E
Hi guys,
I have a KX3 with roofing filters installed. I also have an IC-7300. Will KX3
have an advantage on receive in noisy environment and what is the best way to
use them (SSB and CW)?
Thanks!MikeAB3VN
__
Elecraft mailing list
Home: h
I know I'm probably stupid and missing something obvious, but when I turn
on the sub receiver it is much louder in my right ear than the main is in my
left with the AF gain set the same on both receivers and both VFO's tuned
to the same frequency. RF gain is set the same on both receivers. I
balance.
If you are in balance mode and you want them to be the same you have to
set the Sub AF Gain knob to the middle.
Buck
k4ia
K3# 101 KX3 #715
On 7/19/2014 5:11 PM, Mike via Elecraft wrote:
> I know I'm probably stupid and missing something obvious, but when I turn
> on the sub
15 KW Generac with 550 gal propane tank. Live out in the country and have
gone 14 days without power. I'm good for 2-4 weeks, depending on load.
Mike KD8RQE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
I've been happy with 2 Palstar SP30B's.
Mike KD8RQE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http:/
Any advantage to ordering during the Hamvention? If so, do the same
discounts apply to phone or internet orders or do you have to be physically
present in Dayton to take advantage? Thanks.
73
Mike KD8RQE
__
Elecraft mailing list
Ho
Will the Begali "Adventure" paddles fit the KX2 as well as the KX3?
Mike KD8RQE
In a message dated 5/19/2016 5:37:10 P.M. Eastern Daylight Time,
n...@elecraft.com writes:
Introducing the Elecraft KX2 transceiver -- the newest member of our
compact KX Line. The KX2 has features very simila
A K2 kit is on it's way. Although I do have some experience soldering, it
has been 30+ years and I am open to any suggestions as to equipment
needed. I have a Hakko FS-951 soldering station. I have seen various
mechanisms
for holding the circuit boards while working on them. Any other ti
Thanks for all he replies and advice. I'm looking forward to enjoying this
project. It's been quite a while since I've built anything and I remember
it fondly.
73
Mike KD8RQE
__
Elecraft mailing list
Home: http://mailman.qth.net/mai
Ed, KL7UW, built me a nice 80w 2m amp for less than $400.
http://www.kl7uw.com
Mike
In a message dated 7/28/2016 12:54:12 P.M. Eastern Daylight Time,
dhand...@plantron.se writes:
Does anyone use a KX3 + internal 2m transverter with an external amplifier?
I am looking for any recommenda
20 matches
Mail list logo