[Elecraft] [Elecraft} K3 power fluctuation

2012-06-11 Thread Bill Braithwaite
I am new at this so if I am screwing up please understand.

My K3 has started something new that has me wondering.
I any mode when the power output is adjusted to more than
30 watts the power output constantly fluctuates between zero
and the full 100 watts, never going back to what the control is
set at.
This just started and I am looking for help.
Thank you.
Bill  W4NML
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


[Elecraft] [Elecraft} K3 power fluctuation

2012-06-11 Thread Adrian
Check for excessive volt drop between your power supply and the K3 APP
input.

Try a heavier shorter custom DC line via a new APP plug with a good power
supply set at 15v.

A 30amp good quality comms grade switch mode on your P3 etc. can keep it
close.
Try a different known good power supply also, if problem persists.

Power level fluctuation like you describe, was an issue here too until I did
above, along with cleaning up the TX signal

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill Braithwaite
Sent: Tuesday, 12 June 2012 3:00 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] [Elecraft} K3 power fluctuation

I am new at this so if I am screwing up please understand.

My K3 has started something new that has me wondering.
I any mode when the power output is adjusted to more than
30 watts the power output constantly fluctuates between zero and the full
100 watts, never going back to what the control is set at.
This just started and I am looking for help.
Thank you.
Bill  W4NML
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


Re: [Elecraft] [Elecraft} K3 power fluctuation

2012-06-11 Thread Adrian
Bill, Can you measure the voltage at the APP connector on rear of K3 during
a 50w and 100 w key?

 

A TX gain calibration sound like a good idea, using the K3 Utility and a 50w
dummy load direct on the back of the K3.

Cantenna's and other coaxial connect DL's sometimes give XL issues on some
bands messing up the calibration, as

the K3 swr detection is sensitive to slight mismatches during the
calibration.

 

The pl259 heatsink type that screw direct on work well for this purpose.

 

From: Bill Braithwaite [mailto:w4...@cableone.net] 
Sent: Tuesday, 12 June 2012 5:50 AM
To: Adrian
Subject: Re: [Elecraft] [Elecraft} K3 power fluctuation

 

Adrian,

The power cable in good heavy duty type wire.
The power supply is also a good solid heavy duty supply.
Have also switched the PS and get the same results.
I do not have a P3.

Thanks for your input. Looking for all the help I can get.
Bill



On Mon, Jun 11, 2012 at 1:43 PM, Adrian vk4...@bigpond.com wrote:

Check for excessive volt drop between your power supply and the K3 APP
input.

Try a heavier shorter custom DC line via a new APP plug with a good power
supply set at 15v.

A 30amp good quality comms grade switch mode on your P3 etc. can keep it
close.
Try a different known good power supply also, if problem persists.

Power level fluctuation like you describe, was an issue here too until I did
above, along with cleaning up the TX signal

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill Braithwaite
Sent: Tuesday, 12 June 2012 3:00 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] [Elecraft} K3 power fluctuation

I am new at this so if I am screwing up please understand.

My K3 has started something new that has me wondering.
I any mode when the power output is adjusted to more than
30 watts the power output constantly fluctuates between zero and the full
100 watts, never going back to what the control is set at.
This just started and I am looking for help.
Thank you.
Bill  W4NML
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html