Ian,
Yabut... Mount it to what? With the DB25 connectors
mounted on opposite sides like that I can't really mount it inside my
controller box because one side goes to the pendant, and the other
side goes to the parallel port on the computer.
Mark
At 12:35 PM 9/18/2010, you wrote:
At 07:40 PM 9/18/2010, you wrote:
Gawd, have you guys tried to find
a parallel cable that is DB25 to DB25 male to female in any store
lately?
Digi-Key AE1374 from Assmann, this is good for IEEE-1284 (EPP mode)
as well as all other purposes.
Jon
Yeah, that's the one I originally
So, I might have mentioned that I received a new pendant and got it
hooked up and running the other day. I'd been using one of the
Logitech joypads, and while it didn't do incremental jogs, it did do
continuos motion jogs by holding the joy stick over.
I was playing around over the weekend,
And then Don Stanley wrote:
Hi All;
I will have to plead the Shultz Defense.
The Mill processors I am converting to EMC2 are
Athlon 64 processor 3700+ or better with the following
slots:
PCI
PCI-EX1
PCI-EX16
MGP (Mach speed graphics port).
I am currently using
On 19 September 2010 12:43, Mark Wendt (Contractor)
mark.we...@nrl.navy.mil wrote:
I'm concerned the mux4 calls in the first file would cause problems
with the mux 4 calls in the second file. Are my concerns warranted?
Yes. But the solution is easy.
Just combine the mux4s with loadrt mux4
Hi Mark,
Some of the CNC4PC boards are almost unmountable.. I think he leaves
out the holes to minimize the board space and the cost.. But I sure
wish he would add in a half square inch of extra board space for holes!
I'd pay another dollar or two for holes!
If I wanted to panel mount that
You could just pop it in a metal box - mount it using one
of the DB25s, make up a short DB25m - DB25f cable and mount
the free end of that to the box adjacent to the first DB25 -
i.e. one under the other. Of course, the other end of the
short cable plugs into the other side of your board.
Igor Chudov wrote:
Chris, I actually have a Ferguson R15 rotary indexer. I have no idea
how it works, it was a good deal at auction. Do you know how those
things work, do I need special cams for each operation (number of
positions), or what?
There are some indexers made for CNC work that
Kent A. Reed wrote:
For this old fogey, the phrase Shultz defense brings to mind Hogan's
Heroes and Sergeant Schultz. Is this what you meant
I was puzzled by that reference, but that's GOT to be it! That high-pitched
I know nothing! NOTHING
Jon
Igor,
My Uncle has a few of those Haas 5C units. Back in the late 80's or early 90's
Haas sent me a small potted interface box to allow the Haas 5C to be used on
our Hurco mill. 4 wires to the CNC, 4 wires to Haas. Its a simple opto
isolation unit. I have the schematic for it.
Basically most
Hi All,
I need to advance the A Axis in a while loop and when a photo cell changes
state, then advance to a predetermine position.
Also the functions:
Looping: do, while, endwhile, break, continue
Not too sure which file to place the code for M100 to M199.
Maybe be there is a tutorial or two
On Sun, 19 Sep 2010 12:00:30 -0400, you wrote:
Some of the CNC4PC boards are almost unmountable.. I think he leaves
out the holes to minimize the board space and the cost.. But I sure
wish he would add in a half square inch of extra board space for holes!
All the CNC4PC boards I've tested
On 18/09/10 07:49, Don Stanley wrote:
Hi All;
I will have to plead the Shultz Defense.
The Mill processors I am converting to EMC2 are
Athlon 64 processor 3700+ or better with the following
slots:
PCI
PCI-EX1
PCI-EX16
MGP (Mach speed graphics port).
I am currently
Hi All,
We are using the Mesa 5i20 card in 24 I/O mode.
Cheers,
Howard
Hi All,
I need to advance the A Axis in a while loop and when a photo cell changes
state, then advance to a predetermine position.
Also the functions:
Looping: do, while, endwhile, break, continue
Not too sure which
Hi
it happen with me also. I turn off machine/EMC2 and when i restart next
day EMC2 behave differently- constant error for all axis. while all axis
work perfectly before.
My solution for that problem - put CD back and install new copy of EMC2.
Hi guys,
today I started my machine and EMC2
15 matches
Mail list logo
