[Emc-users] Emco 140 lathe retrofit

Hello. I have a Emcoturn 140 lathe. i am going to use linuxcnc for retrofitting, and i will use the 5 ph stepper drives. but does anyone know anything about step timing for these drives? Best regards-- Med vennlig hilsen Bjørn Kristiansen www.spesmek.no tel: +47 971 51 959

Re: [Emc-users] Latency problem

; that came with it is only 60w. and i see in the manual that G0 = Full power > 30 W but G1 = 5 W < power < 52.5 W then with the SSD it could be that it's to smal and running hot. I will test with a "real powersupply" after the hollydays. To be continued.. Tusen ta

Re: [Emc-users] Latency problem

out SATA and SSD disk could that have some influence on the latency? But anyway i still think i have some powersave funktion running. I noticed that the screen was black when i come back to the office, witch i havent seen before. I think i have to go back to check my bios version to see if there

Re: [Emc-users] Latency problem

f ACPI my bios is: MWNT10N.86A.0083.2011.0524.1600 is this the same as others are running? and do you have option to turn off ACPI from bios? -- Regards: Bjørn Kristiansen -- Everyone hates slow websites.

Re: [Emc-users] Latency problem

Am 20.03.2013 um 08:48 schrieb Bj?rn: > I bougt this. > http://www.ebay.com/itm/200542103383?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 > running the latest version of linuxcnc. specifically which version? I have a D525MW and get much better results > Hypertreading off in bios, > ISOLCP

[Emc-users] Latency problem

I bougt this. http://www.ebay.com/itm/200542103383?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 running the latest version of linuxcnc. Hypertreading off in bios, ISOLCPU is done. when runnnig latencytest and 3 x glxgears + some video i can run for 30 min and get: servo thread (1.0ms) max

Re: [Emc-users] Repost: Teach with joystick. (Welding)

mowement. i think i hawe too play a litle with this too se how it works.. Bjørn.. on., 13.08.2008 kl. 09.36 +0200, skrev Jonathan / Hydra: > A more elegant solution based on the same principle if you need a > continuous track would be to generate a probe hit signal when the the > current pos

Re: [Emc-users] Repost: Teach with joystick. (Welding)

adjust the speed of the switcing you would get as many coordinates as you need to get a smooth mowement to a robot. could i be on to somehing?? Bjørn. ti., 12.08.2008 kl. 12.29 -0400, skrev Organic Engines: > Hi Craig, > > > 1. Software to Generate basic G-code from a sequence

Re: [Emc-users] Teach-in.

where did you find the teach-in function? i have a kind of robot where that would have been wery helpfull to program the moves, i was thinking aboat how i could make that kind of programming possible, and was not aware that someone already has been working with someting like that. Bjørn. :) ti

[Emc-users] Homing by code

Hello folks.. in other machine controllers i have used the G28 made the machine go home to the homeswitches in EMC it only goes to 0.0.0 Is there any way too program a real home that works just like hitting ctrl home? regards Bjørn

[Emc-users] [Fwd: [Fwd: Shared home and limit]]

when homing you set "home ignore limits in the .ini file and if you want to home in negative direction you set - in front of the homing speed in the .ini file. I hope this will be helpfull. Regards Bjørn.. --