On 1/19/23 21:32, Bari wrote:
Naa already been done
https://forum.linuxcnc.org/27-driver-boards/46770-driver-firmware-pcb-for-pi-rp2040-pio-i-e-an-easy-to-configure-fpga-like-card but sadly they haven't shared their source yet.
Plus you still need Ethernet and some protection on the
Naa already been done
https://forum.linuxcnc.org/27-driver-boards/46770-driver-firmware-pcb-for-pi-rp2040-pio-i-e-an-easy-to-configure-fpga-like-card
but sadly they haven't shared their source yet.
Plus you still need Ethernet and some protection on the IO's and
connectors so many
Thanks Chris I hadn't seen this 7i92. I was just looking at 7i76 as that was
what I was familiar with.
May have to put in a Mesa order;-)
Linden
On January 19, 2023 9:25:30 a.m. PST, Chris Albertson
wrote:
>This card seems to be in-stock at the Mesa website. I'd go with Ethernet
>because
On Thu, Jan 19, 2023 at 11:20 AM Linden via Emc-users <
emc-users@lists.sourceforge.net> wrote:
>
> Any idea when the Ethernet cards will be produced and sold again??
>
I just put two of them in my shopping card, only one gave the "out of stock
notice" One had the female pins, the other male
but is
in the photo.
-Original Message-
From: andy pugh [mailto:bodge...@gmail.com]
Sent: January-19-23 4:23 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Available fanless PC for linuxcnc with parallel
port
On Thu, 19 Jan 2023 at 09:51, Robin Szemeti via Emc-users
> -Original Message-
> > From: andy pugh [mailto:bodge...@gmail.com]
> > Sent: January-19-23 4:23 AM
> > To: Enhanced Machine Controller (EMC)
> > Subject: Re: [Emc-users] Available fanless PC for linuxcnc with parallel
> port
> >
> > On Thu, 19
This card seems to be in-stock at the Mesa website. I'd go with Ethernet
because it gives you the option later to use computers with no PCIe bus.
Maybe a Rapberry Pi or something like that. Also the Ethernet cable gives
you flexibility as it can be up to 100 meters long.
7I92TH Anything I/O
On Thu, Jan 19, 2023 at 4:26 AM andy pugh wrote:
> On Thu, 19 Jan 2023 at 09:51, Robin Szemeti via Emc-users
> wrote:
> >
> > I'll be surprised if you can find anythign with a parallel port,
>
> That's just not the case. (though many don't have them in the case)
>
> With parallel port:
>
>
nced Machine Controller (EMC)
> Subject: Re: [Emc-users] Available fanless PC for linuxcnc with parallel port
>
> On Thu, 19 Jan 2023 at 09:51, Robin Szemeti via Emc-users
> wrote:
> >
> > I'll be surprised if you can find anythign with a parallel port,
>
> That's just
On Thu, 19 Jan 2023, andy pugh wrote:
> On Thu, 19 Jan 2023 at 03:45, Linden via Emc-users
> wrote:
>
>> My original old dell gave up and died several years ago. The pci 1
>> parallel port card I have is not recognized by the bios of either of my
>> other 2 computers and I cant find a header
On Thu, 19 Jan 2023 at 03:45, Linden via Emc-users
wrote:
> My original old dell gave up and died several years ago. The pci 1
> parallel port card I have is not recognized by the bios of either of my
> other 2 computers and I cant find a header cable in my junk to go from
> the lp1 pins on my
On Thu, 19 Jan 2023 at 09:51, Robin Szemeti via Emc-users
wrote:
>
> I'll be surprised if you can find anythign with a parallel port,
That's just not the case. (though many don't have them in the case)
With parallel port:
Chris Albertson [mailto:albertson.ch...@gmail.com]
> > Sent: January-18-23 10:39 PM
> > To: Enhanced Machine Controller (EMC)
> > Subject: Re: [Emc-users] Available fanless PC for linuxcnc with parallel
> port
> >
> > My go to place is Newegg.com They sell all kinds of o
age-
> From: Chris Albertson [mailto:albertson.ch...@gmail.com]
> Sent: January-18-23 10:39 PM
> To: Enhanced Machine Controller (EMC)
> Subject: Re: [Emc-users] Available fanless PC for linuxcnc with parallel port
>
> My go to place is Newegg.com They sell all kinds
My go to place is Newegg.com They sell all kinds of off lease used PCs but
getting one known to work with a parallel printer port is getting to be
hard.That is fine as Mesa cards are reasonably affordable.
I just checked and they have dozens of options for $80. Typically an Intel
i3 with
On 1/18/23 22:43, Linden via Emc-users wrote:
Does any one have suggestions for a reasonably priced and available fan
less pc with a parallel port that I can use with linux cnc to go with my
gecko 540?
Looking to spend under $300 if possible with shipping
My original old dell gave up and
Does any one have suggestions for a reasonably priced and available fan
less pc with a parallel port that I can use with linux cnc to go with my
gecko 540?
Looking to spend under $300 if possible with shipping
My original old dell gave up and died several years ago. The pci 1
parallel port
17 matches
Mail list logo