On Friday 11 May 2018 18:32:44 Gregg Eshelman via Emc-users wrote:
> An idea for putting a square hole at the end of a round one, without
> having to use special tooling. Mill brass bar stock into a pair of
> small L shapes, with one leg just as long as the width of the tap
> shank.Position the tw
On Friday 11 May 2018 18:20:13 Gregg Eshelman via Emc-users wrote:
> Rent space on the tower for cell phone and wireless internet antennas.
> That's what the grain elevator across the street from me did, top of
> one building has phone antennas all around it.
>
We were going to do that, but it tur
An idea for putting a square hole at the end of a round one, without having to
use special tooling.
Mill brass bar stock into a pair of small L shapes, with one leg just as long
as the width of the tap shank.Position the two pieces to make a square hole
then silver solder together. Cut off exces
Rent space on the tower for cell phone and wireless internet antennas. That's
what the grain elevator across the street from me did, top of one building has
phone antennas all around it.
On Friday, May 11, 2018, 6:46:50 AM MDT, Erik Christiansen
wrote:
On 11.05.18 07:42, Gene Hesket
Like these? Transmission Gear Kit | Steel Gear Kit - LittleMachineShop.com
|
|
|
| $54.95 | |
|
|
|
| |
Transmission Gear Kit | Steel Gear Kit - LittleMachineShop.com
Never break expensive or hard-to-replace gears again! Once installed on your
mini mill, this kit replaces plasti...
|
On Friday 11 May 2018 09:22:16 Ken Strauss wrote:
> You'll need a funny stud since most drill chucks are 3/8-inch NF and
> most small T-nuts are 3/8-inch NC.
>
Already thought of that.
I figure a T nut is easy enough to make. Or I've the pi controlled
Sheldon and can make the short stud easy eno
[Emc-users] Tap Hats [Was: Re: More on er-20 stuffs
>
> On Friday 11 May 2018 08:42:58 Erik Christiansen wrote:
>
> > On 11.05.18 07:42, Gene Heskett wrote:
> > > On Friday 11 May 2018 03:32:39 Erik Christiansen wrote:
> > > A box or three of grubscrews off fleabay won
On Friday 11 May 2018 08:42:58 Erik Christiansen wrote:
> On 11.05.18 07:42, Gene Heskett wrote:
> > On Friday 11 May 2018 03:32:39 Erik Christiansen wrote:
> > A box or three of grubscrews off fleabay won't add up
> >
> > > to much cost. The last boxful I bought was M3 to M10, IIRC. You
> > > mig
On 11.05.18 07:42, Gene Heskett wrote:
> On Friday 11 May 2018 03:32:39 Erik Christiansen wrote:
> A box or three of grubscrews off fleabay won't add up
> > to much cost. The last boxful I bought was M3 to M10, IIRC. You might
> > do better buying plastic bags of each size, for quantity.
> >
> That
On Friday 11 May 2018 03:32:39 Erik Christiansen wrote:
> On 11.05.18 01:25, Gene Heskett wrote:
> > On Thursday 10 May 2018 22:23:56 Erik Christiansen wrote:
> > > But, whoa. I'm also not fully across the need for bore adjustment.
> > > As taps are ground from a few stock sizes, only those few si
On 11.05.18 01:25, Gene Heskett wrote:
> On Thursday 10 May 2018 22:23:56 Erik Christiansen wrote:
> > But, whoa. I'm also not fully across the need for bore adjustment. As
> > taps are ground from a few stock sizes, only those few sizes of tap
> > hat bore are needed. While I found a drill close e
11 matches
Mail list logo