Re: Toshiba Portégé 4000 laptop
Okay the solution is to disable COM and Parallel ports in the bios. (Maybe also USB KB, and USB FDD). To access the bios you have to press ESC while the red TOSHIBA boot screen is displayed, then press F1. (I explain that becaused it's undocumented). With the default settings, I even got the 5.x kernel to panic. Really strange. Thanks for your help ;) On 4/23/05, Laurent Debacker [EMAIL PROTECTED] wrote: With FreeSBIE 1.1 (based on FreeBSD 5.3), it says: acd0: TIMEOUT - READ_BIG retrying (2 retries left) acd0: TIMEOUT - READ_BIG timed out Then it stop/freezes. If I press the power button, it says acpi: suspend request ignored (not ready yet). Thanks. On 4/23/05, Laurent Debacker [EMAIL PROTECTED] wrote: I tried 5.4-RC3 with no ACPI, safe mode, and DEBUG mode, without success. DEBUG doesn't repport anything. 5.3 also crashes in safe mode, and no ACPI, freezes after pci0: PCI bus on pcib0. dmesg on 4.11 reports: ohci0: AcerLabs M5237 (Aladdin-V) USB controller mem 0xf7eff000-0xf7ef irq 11 at device 2.0 on pci0. You can see full report below. Thank you for your help ;) Laurent. Here are drivers loaded by 4.11 as reported by dmesg: md0: Preloaded image /mfsroot 4423680 bytes at 0xc03edc14 md1: Malloc disk Using $PIR table, 9 entries at 0xc00f01d0 npx0: math processor on motherboard npx0: INT 16 interface pcib0: Host to PCI bridge on motherboard pci0: PCI bus on pcib0 pcib1: Acerlabs M5247 PCI-PCI(AGP Supported) bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 pci1: Trident model 8820 VGA-compatible display device at 0.0 irq 11 ohci0: AcerLabs M5237 (Aladdin-V) USB controller mem 0xf7eff000-0xf7ef irq 11 at device 2.0 on pci0 usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: AcerLabs M5237 (Aladdin-V) USB controller on ohci0 usb0: USB revision 1.0 uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered atapci0: AcerLabs Aladin ATA66 controller port 0xeff0-0xefff at device 4.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: unknown card (vendor=0x10b9, dev=0x5451) at 6.0 isab0: AcerLabs M1533 portable PCI-ISA bridge at device 7.0 on pci0 isa0: ISA bus on isab0 chip1: AcerLabs M15x3 Power Management Unit at device 8.0 on pci0 fxp0: Intel 82559 Pro/100 Ethernet port 0xeec0-0xeeff mem 0xf7d0-0xf7df,0xf7efe000-0xf7efefff irq 11 at device 10.0 on pci0 fxp0: Ethernet address 00:00:39:a7:a0:b4 inphy0: i82555 10/100 media interface on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci_cfgintr_linked: linked (3) to hard-routed irq 11 pci_cfgintr: 0:16 INTA routed to irq11 pcic0: TI PCI-1410 PCI-CardBus Bridge irq 11 at device 16.0 on pci0 pcic0: PCI Memory allocated: 0x8800 pcic0: TI12XX PCI Config Reg: [pwr save][pci only] pccard0: PC Card 16-bit bus (classic) on pcic0 pci_cfgintr_linked: linked (1) to hard-routed irq 11 pci_cfgintr: 0:17 INTA routed to irq11 pcic1: Toshiba ToPIC100 PCI-CardBus Bridge irq 11 at device 17.0 on pci0 pcic1: PCI Memory allocated: 0x88001000 pccard1: PC Card 16-bit bus (classic) on pcic1 pci_cfgintr_linked: linked (2) to hard-routed irq 11 pci_cfgintr: 0:17 INTB routed to irq11 pcic2: Toshiba ToPIC100 PCI-CardBus Bridge irq 11 at device 17.1 on pci0 pcic2: PCI Memory allocated: 0x88002000 pccard2: PC Card 16-bit bus (classic) on pcic2 pci0: unknown card (vendor=0x1179, dev=0x0805) at 18.0 orm0: Option ROMs at iomem 0xc-0xcbfff,0xe-0xe on isa0 pmtimer0 on isa0 fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: Keyboard controller (i8042) at port 0x60,0x64 on isa0 atkbd0: AT Keyboard flags 0x1 irq1 on atkbdc0 kbd0 at atkbd0 psm0: PS/2 Mouse irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: Generic ISA VGA at port 0x3c0-0x3df iomem 0xa-0xb on isa0 sc0: System console at flags 0x100 on isa0 sc0: VGA 16 virtual consoles, flags=0x300 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: parallel port not found. pccard: card inserted, slot0 pccard: card removed, slot0 ad0: 16077MB IC25N020ATCS04-0 [38760/16/63] at ata0-master UDMA66 acd0: DVD-ROM TOSHIBA DVD-ROM SD-C2502 at ata1-master PIO4 On 4/23/05, Kevin Kinsey [EMAIL PROTECTED] wrote: Laurent Debacker wrote: Hello, Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It detects my CPU, RAM, some ACPI stuffs.. I noticed pci1: display, VGA at device 0.0 (no driver attached). I don't know if it's ok. At the end, it says ohci0: [GIANT-LOCKED] then usb0: OHCI version 1.0, legacy support, then nothing. FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;) Any idea? Thank you, Laurent Debacker.
Toshiba Portégé 4000 laptop
Hello, Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It detects my CPU, RAM, some ACPI stuffs.. I noticed pci1: display, VGA at device 0.0 (no driver attached). I don't know if it's ok. At the end, it says ohci0: [GIANT-LOCKED] then usb0: OHCI version 1.0, legacy support, then nothing. FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;) Any idea? Thank you, Laurent Debacker. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Toshiba Portégé 4000 laptop
Laurent Debacker wrote: Hello, Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It detects my CPU, RAM, some ACPI stuffs.. I noticed pci1: display, VGA at device 0.0 (no driver attached). I don't know if it's ok. At the end, it says ohci0: [GIANT-LOCKED] then usb0: OHCI version 1.0, legacy support, then nothing. FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;) Any idea? Thank you, Laurent Debacker. What does the 4.11 dmesg say about the ochi device? Can you boot safe mode on 5.X? Have you tried booting with ACPI disabled? HTH, KDK ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: Toshiba Portégé 4000 laptop
With FreeSBIE 1.1 (based on FreeBSD 5.3), it says: acd0: TIMEOUT - READ_BIG retrying (2 retries left) acd0: TIMEOUT - READ_BIG timed out Then it stop/freezes. If I press the power button, it says acpi: suspend request ignored (not ready yet). Thanks. On 4/23/05, Laurent Debacker [EMAIL PROTECTED] wrote: I tried 5.4-RC3 with no ACPI, safe mode, and DEBUG mode, without success. DEBUG doesn't repport anything. 5.3 also crashes in safe mode, and no ACPI, freezes after pci0: PCI bus on pcib0. dmesg on 4.11 reports: ohci0: AcerLabs M5237 (Aladdin-V) USB controller mem 0xf7eff000-0xf7ef irq 11 at device 2.0 on pci0. You can see full report below. Thank you for your help ;) Laurent. Here are drivers loaded by 4.11 as reported by dmesg: md0: Preloaded image /mfsroot 4423680 bytes at 0xc03edc14 md1: Malloc disk Using $PIR table, 9 entries at 0xc00f01d0 npx0: math processor on motherboard npx0: INT 16 interface pcib0: Host to PCI bridge on motherboard pci0: PCI bus on pcib0 pcib1: Acerlabs M5247 PCI-PCI(AGP Supported) bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 pci1: Trident model 8820 VGA-compatible display device at 0.0 irq 11 ohci0: AcerLabs M5237 (Aladdin-V) USB controller mem 0xf7eff000-0xf7ef irq 11 at device 2.0 on pci0 usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: AcerLabs M5237 (Aladdin-V) USB controller on ohci0 usb0: USB revision 1.0 uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered atapci0: AcerLabs Aladin ATA66 controller port 0xeff0-0xefff at device 4.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: unknown card (vendor=0x10b9, dev=0x5451) at 6.0 isab0: AcerLabs M1533 portable PCI-ISA bridge at device 7.0 on pci0 isa0: ISA bus on isab0 chip1: AcerLabs M15x3 Power Management Unit at device 8.0 on pci0 fxp0: Intel 82559 Pro/100 Ethernet port 0xeec0-0xeeff mem 0xf7d0-0xf7df,0xf7efe000-0xf7efefff irq 11 at device 10.0 on pci0 fxp0: Ethernet address 00:00:39:a7:a0:b4 inphy0: i82555 10/100 media interface on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci_cfgintr_linked: linked (3) to hard-routed irq 11 pci_cfgintr: 0:16 INTA routed to irq11 pcic0: TI PCI-1410 PCI-CardBus Bridge irq 11 at device 16.0 on pci0 pcic0: PCI Memory allocated: 0x8800 pcic0: TI12XX PCI Config Reg: [pwr save][pci only] pccard0: PC Card 16-bit bus (classic) on pcic0 pci_cfgintr_linked: linked (1) to hard-routed irq 11 pci_cfgintr: 0:17 INTA routed to irq11 pcic1: Toshiba ToPIC100 PCI-CardBus Bridge irq 11 at device 17.0 on pci0 pcic1: PCI Memory allocated: 0x88001000 pccard1: PC Card 16-bit bus (classic) on pcic1 pci_cfgintr_linked: linked (2) to hard-routed irq 11 pci_cfgintr: 0:17 INTB routed to irq11 pcic2: Toshiba ToPIC100 PCI-CardBus Bridge irq 11 at device 17.1 on pci0 pcic2: PCI Memory allocated: 0x88002000 pccard2: PC Card 16-bit bus (classic) on pcic2 pci0: unknown card (vendor=0x1179, dev=0x0805) at 18.0 orm0: Option ROMs at iomem 0xc-0xcbfff,0xe-0xe on isa0 pmtimer0 on isa0 fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: Keyboard controller (i8042) at port 0x60,0x64 on isa0 atkbd0: AT Keyboard flags 0x1 irq1 on atkbdc0 kbd0 at atkbd0 psm0: PS/2 Mouse irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: Generic ISA VGA at port 0x3c0-0x3df iomem 0xa-0xb on isa0 sc0: System console at flags 0x100 on isa0 sc0: VGA 16 virtual consoles, flags=0x300 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: parallel port not found. pccard: card inserted, slot0 pccard: card removed, slot0 ad0: 16077MB IC25N020ATCS04-0 [38760/16/63] at ata0-master UDMA66 acd0: DVD-ROM TOSHIBA DVD-ROM SD-C2502 at ata1-master PIO4 On 4/23/05, Kevin Kinsey [EMAIL PROTECTED] wrote: Laurent Debacker wrote: Hello, Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It detects my CPU, RAM, some ACPI stuffs.. I noticed pci1: display, VGA at device 0.0 (no driver attached). I don't know if it's ok. At the end, it says ohci0: [GIANT-LOCKED] then usb0: OHCI version 1.0, legacy support, then nothing. FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;) Any idea? Thank you, Laurent Debacker. What does the 4.11 dmesg say about the ochi device? Can you boot safe mode on 5.X? Have you tried booting with ACPI disabled? HTH, KDK ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
