Quite correct. I have done this for several perl versions now, and
the work involved is quite scarey.
Not that I'm a fan of the GPL, but wouldn't importation of gmake
into the toolchain that gets installed by default help this problem
along enormously?
No. It will make it worse.
M
Hi all,
I'd like to add some of my experiences with BP6. I tried to create
software RAID using vinum (I tried RAID-1 and RAID-5) on 4x14GB drives
connected to HighPoint ATA66 in UDMA66 mode. I experienced
serious problems until I overclocked the bus to 78 MHz. I wasn't
able even to do newfs on
On Wed, 27 Dec 2000, Soren Schmidt wrote:
It seems David W. Chapman Jr. wrote:
You guys are not overclocking are you ??
I've recently seen the same problem on 4.2-stable, probably a early version
of it, I go to make my kernel and it locks up for a few mins, then I get
some ata error
You guys are not overclocking are you ??
No! Just because I have a BP6 doesn't mean I'm overclocking it. The HPT
controller has always done this. Would more messages help, eg bootverbose?
I tried DDB on 4.0 and ctrl-esc didn't get out of this state.
--Ben
To Unsubscribe: send mail to
I've got two mobos with VIA MVP3 chipsets on-board. As these systems
(until recently) had only SCSI peripherals, I didn't notice any problem.
However, when I added an IDE CDRW drive, I got these very strange system
lock-ups/hangs. Specifically, this was an FIC VA-503+ mobo, with a
450MHz K6-2
please i need help...
that hpt370 is starting to piss me off. i've been searching up and down the
archives but all i did find was a mail by someone who modified line 212 in
/usr/src/sys/dev/ata/ata-raid.c. i did that too and rebuilt the kernel but
that didnt quite do the job.
i have 2 HDDs,
"MA" == Matthias Andree [EMAIL PROTECTED] writes:
--cut here--
me:\
:umask=0707:\
:tc=default:
--cut here--
MA Can people change the permissions afterwards or the umask before
MA uploading, thus circumventing these settings? I'm not too deep in ftpd.
Hmmm. Yes. According to the ftpd man
On Wed, 27 Dec 2000, Vivek Khera wrote:
MA Can people change the permissions afterwards or the umask before
MA uploading, thus circumventing these settings? I'm not too deep in ftpd.
Hmmm. Yes. According to the ftpd man page, there are commands "SITE
CHMOD" and "SITE UMASK" that will
On Wed, 27 Dec 2000, Louis A. Mamakos wrote:
I've got two mobos with VIA MVP3 chipsets on-board. As these systems
(until recently) had only SCSI peripherals, I didn't notice any problem.
However, when I added an IDE CDRW drive, I got these very strange system
lock-ups/hangs.
is it enough if I make make buildworld ?
anyway thanks for the help. now I could compile kernel
without any problem. I didnt know that I have to make world etc.
Since when this is required? (or is it required?)
On Wed, 27 Dec 2000, Donn Miller wrote:
On Wed, 27 Dec 2000, Evren Yurtesen wrote:
On Wed, 27 Dec 2000, Evren Yurtesen wrote:
is it enough if I make make buildworld ?
anyway thanks for the help. now I could compile kernel
without any problem. I didnt know that I have to make world etc.
Since when this is required? (or is it required?)
I knew it was the problem, since
Soren Schmidt wrote:
It seems Justin W. Pauler wrote:
I've heard tell that there are problems with the VIA chipset and UDMA on
FreeBSD. Is this true, and if so, what is the problem with?
Hmm, there are no open problems as far as I'm aware...
FreeBSD 4.2-STABLE #0: Fri Dec 8
I have a KT7 with an athlon 1.1, no problems with ATA66, don't have a 100
drive though. Works fine, does make worlds in a little over an hour with
384mb of pc133, but I do have to downclock the pc133 to 100 because these
via chips have some problem with agp and pc133 at the moment.
I have an
Date: Wed, 27 Dec 2000 16:44:08 -0500 (EST)
From: Donn Miller [EMAIL PROTECTED]
Sender: [EMAIL PROTECTED]
On Wed, 27 Dec 2000, Evren Yurtesen wrote:
is it enough if I make make buildworld ?
anyway thanks for the help. now I could compile kernel
without any problem. I didnt know
"David W. Chapman Jr." wrote:
I have a KT7 with an athlon 1.1, no problems with ATA66, don't have a 100
drive though. Works fine, does make worlds in a little over an hour with
384mb of pc133, but I do have to downclock the pc133 to 100 because these
via chips have some problem with agp
15 matches
Mail list logo
