Re: [gentoo-user] hardware - memory problem
On 12/16/2020 03:51 PM, antlists wrote: > Or is this a 32-bit system WITHOUT extended memory support? > > I don't properly understand it, but with a 32-bit system the kernel uses > 1GB of memory and user-space uses the other 3GB. Extended memory support > means each process can have its own 3GB space which enables you to use > all available memory, but without it I think the entire system is stuck > in the first 4GB. > > Cheers, > Wol Hm..., did I use wrong stage? stage3-i686-20201116T214503Z.tar.xz on: AMD FX(tm)-8150 Eight-Core Processor
Re: [gentoo-user] hardware - memory problem
On 12/16/2020 03:34 PM, Mark Knecht wrote: > On Wed, Dec 16, 2020 at 3:29 PM Mark Knecht wrote: >> >> >> >> On Wed, Dec 16, 2020 at 3:22 PM wrote: >>> >>> I run Memtest86 on my old box and it completed 1pass without any errors. >>> Memtest86 reports 16G memory >>> >>> When I boot Gentoo it shows only 3282Mb >>> free -m >>> totalusedfree shared buff/cache >>> available >>> Mem: 3282 1252475 7 680 >>> 3033 >>> >>> Is it a motherboard? How to test it? >>> >> >> Start with >> >> cat /proc/meminfo > >> > Or lshw and look for the DIMM modules themselves cat /proc/meminfo MemTotal:3360992 kB MemFree: 2806556 kB MemAvailable:3077952 kB Buffers: 97156 kB Cached: 262116 kB SwapCached:0 kB Active: 329656 kB Inactive: 133864 kB Active(anon): 104804 kB Inactive(anon): 2964 kB Active(file): 224852 kB Inactive(file): 130900 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 2504328 kB HighFree:2120028 kB LowTotal: 856664 kB LowFree: 686528 kB SwapTotal: 8757244 kB SwapFree:8757244 kB Dirty: 292 kB Writeback: 0 kB AnonPages:104252 kB Mapped:93812 kB Shmem: 3516 kB KReclaimable: 34340 kB Slab: 56524 kB SReclaimable: 34340 kB SUnreclaim:22184 kB KernelStack:2256 kB PageTables: 2596 kB NFS_Unstable: 0 kB Bounce:0 kB WritebackTmp: 0 kB CommitLimit:10437740 kB Committed_AS: 987564 kB VmallocTotal: 122880 kB VmallocUsed:4080 kB VmallocChunk: 0 kB Percpu: 1248 kB HugePages_Total: 0 HugePages_Free:0 HugePages_Rsvd:0 HugePages_Surp:0 Hugepagesize: 4096 kB Hugetlb: 0 kB DirectMap4k: 12280 kB DirectMap4M: 32 kB lshw -C memory *-memory description: System Memory physical id: 29 slot: System board or motherboard size: 16GiB *-bank:0 description: DIMM 1333 MHz (0.8 ns) physical id: 0 slot: A0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM 1333 MHz (0.8 ns) physical id: 1 slot: A1 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: DIMM 1333 MHz (0.8 ns) physical id: 2 slot: A2 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: DIMM 1333 MHz (0.8 ns) physical id: 3 slot: A3 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) When I loot at "htop" it only shows: Mem:155M/3.21G
[gentoo-user] ssh Connection reset by port 22
During compiling -uavDN @world one of the package refuse to compile sys-auth/polkit-0.118::gentoo failed (configure phase): econf failed Call stack: ebuild.sh, line 125: Called src_configure environment, line 2211: Called econf '--localstatedir=/var' '--disable-static' '--enable-man-pages' '--disable-gtk-doc' '--disable-examples' '--enable-libelogind' '--enable-introspection' '--enable-nls' '--with-pam-module-dir=/lib/security' '--with-authfw=pam' '--disable-libsystemd-login' '--with-systemdsystemunitdir=/lib/systemd/system' '--disable-test' '--with-os-type=gentoo' phase-helpers.sh, line 680: Called __helpers_die 'econf failed' isolated-functions.sh, line 112: Called die The specific snippet of code: die "$@" Now, I can no longer ssh to to it, I get: Connection reset by 10.0.0.100 port 22
Re: [gentoo-user] ssh Connection reset by port 22
On 12/15/2020 07:53 PM, the...@sys-concept.com wrote: > During compiling -uavDN @world one of the package refuse to compile > > sys-auth/polkit-0.118::gentoo failed (configure phase): > econf failed [snip] > > Now, I can no longer ssh to to it, I get: > Connection reset by 10.0.0.100 port 22 perl-cleaner --reallyall -- -av solved the problem with: sys-auth/polkit-0.118 but I still get the error when trying to ssh: Connection reset by 10.0.0.100 port 22
Re: [gentoo-user] ssh Connection reset by port 22
On 12/15/2020 10:41 PM, cal wrote: > On 12/15/20 9:36 PM, the...@sys-concept.com wrote: >> On 12/15/2020 07:53 PM, the...@sys-concept.com wrote: >>> During compiling -uavDN @world one of the package refuse to compile >>> >>> sys-auth/polkit-0.118::gentoo failed (configure phase): >>> econf failed >> [snip] >>> >>> Now, I can no longer ssh to to it, I get: >>> Connection reset by 10.0.0.100 port 22 >> >> perl-cleaner --reallyall -- -av solved the problem with: >> sys-auth/polkit-0.118 >> but I still get the error when trying to ssh: >> >> Connection reset by 10.0.0.100 port 22 >> > > Is there anything interesting if you run ssh -vvv (you can vary the > amount of 'v's) to increase the verbosity of the ssh client and see what > it's doing prior to the connection reset? > > Have you tried restarting sshd on the server? > Nothing that would indicate any error. OpenSSH_7.5p1-hpn14v12lpk, OpenSSL 1.0.2n 7 Dec 2017 debug1: Reading configuration data /etc/ssh/ssh_config debug2: resolving "10.0.0.100" port 22 debug2: ssh_connect_direct: needpriv 0 debug1: Connecting to 10.0.0.100 [10.0.0.100] port 22. debug1: Connection established. debug1: identity file /home/joseph/.ssh/id_rsa type 1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_rsa-cert type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_dsa type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_dsa-cert type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_ecdsa type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_ecdsa-cert type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_ed25519 type -1 debug1: key_load_public: No such file or directory debug1: identity file /home/joseph/.ssh/id_ed25519-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_7.5p1-hpn14v12lpk debug1: Remote protocol version 2.0, remote software version OpenSSH_8.1 debug1: match: OpenSSH_8.1 pat OpenSSH* compat 0x0400 debug1: Remote is NON-HPN aware debug2: fd 3 setting O_NONBLOCK debug1: Authenticating to 10.0.0.100:22 as 'joseph' debug3: hostkeys_foreach: reading file "/home/joseph/.ssh/known_hosts" debug3: send packet: type 20 debug1: SSH2_MSG_KEXINIT sent Connection reset by 10.0.0.100 port 22
Re: [gentoo-user] ssh Connection reset by port 22
On 12/15/2020 10:41 PM, cal wrote: > On 12/15/20 9:36 PM, the...@sys-concept.com wrote: >> On 12/15/2020 07:53 PM, the...@sys-concept.com wrote: >>> During compiling -uavDN @world one of the package refuse to compile >>> >>> sys-auth/polkit-0.118::gentoo failed (configure phase): >>> econf failed >> [snip] >>> >>> Now, I can no longer ssh to to it, I get: >>> Connection reset by 10.0.0.100 port 22 >> >> perl-cleaner --reallyall -- -av solved the problem with: >> sys-auth/polkit-0.118 >> but I still get the error when trying to ssh: >> >> Connection reset by 10.0.0.100 port 22 >> > > Is there anything interesting if you run ssh -vvv (you can vary the > amount of 'v's) to increase the verbosity of the ssh client and see what > it's doing prior to the connection reset? > > Have you tried restarting sshd on the server? tail -f /var/log/auth.log (on the server) does not show any log-in attempt only: sshd: Server listening on 0.0.0.0 port 22 sshd: Server listening on :: port 22
[gentoo-user] ERROR: asterisk failed to start
This is new asterisk (-13.36.0) installation when I try to start it, I get an error: * Caching service dependencies ... [ ok ] * Starting asterisk PBX ... * Max open filedescriptors : 4096 * Starting asterisk as : asterisk:asterisk (+supplementaries) * Signalling asterisk wrapper script to terminate ... [ !! ] * ERROR: asterisk failed to start When I re-emerge I get: >>> Verifying ebuild manifests >>> Emerging (1 of 1) net-misc/asterisk-13.36.0::gentoo >>> Installing (1 of 1) net-misc/asterisk-13.36.0::gentoo >>> Jobs: 1 of 1 complete !!! existing preserved libs found
Re: [gentoo-user] CPU you selected does not support x86-64 instruction set
On 12/14/2020 09:38 PM, J. Roeleveld wrote: > On 15 December 2020 02:21:22 CET, the...@sys-concept.com wrote: >> >> By mistake on new installation I untar wrong: stage-3 x86_64 instead >> of >> i686 >> >> during kernel compiling I got: >> cc1: error: CPU you selected does not support x86-64 instruction set >> >> Is it possible to untar new stage-3 (i686) over current one, or I need >> to delete all the folders? > > To avoid any leftover files causing issues, I would start over. > > -- > Joost You are correct, it is easier to start over.
Re: [gentoo-user] CPU you selected does not support x86-64 instruction set
On 12/14/2020 11:17 PM, the...@sys-concept.com wrote:
> On 12/14/2020 06:21 PM, the...@sys-concept.com wrote:
>>
>> By mistake on new installation I untar wrong: stage-3 x86_64 instead of
>> i686
>>
>> during kernel compiling I got:
>> cc1: error: CPU you selected does not support x86-64 instruction set
>>
>> Is it possible to untar new stage-3 (i686) over current one, or I need
>> to delete all the folders?
>
> After selecting stage-3 (i686) I still get the same error message when
> trying to compile kernel:
>
> CC scripts/mod/empty.o
> cc1: error: CPU you selected does not support x86-64 instruction set
> make[1]: *** [scripts/Makefile.build:266: scripts/mod/empty.o] Error 1
> make: *** [Makefile:1137: prepare0] Error 2
>
> The CPU I have:
> AMD FX(tm)-8150 Eight-Core Processor
>
> make.conf
> COMMON_FLAGS="-march=native -O2 -pipe"
> #COMMON_FLAGS="-O2 -march=i686 -pipe"
> CFLAGS="${COMMON_FLAGS}"
> CXXFLAGS="${COMMON_FLAGS}"
> FCFLAGS="${COMMON_FLAGS}"
> FFLAGS="${COMMON_FLAGS}"
> CPU_FLAGS_X86="mmx mmxext sse sse2 sse3"
SOLVED:
One need to disable "64-bit kernel" in the root of the menuconfig.
Re: [gentoo-user] CPU you selected does not support x86-64 instruction set
On 12/14/2020 06:21 PM, the...@sys-concept.com wrote:
>
> By mistake on new installation I untar wrong: stage-3 x86_64 instead of
> i686
>
> during kernel compiling I got:
> cc1: error: CPU you selected does not support x86-64 instruction set
>
> Is it possible to untar new stage-3 (i686) over current one, or I need
> to delete all the folders?
After selecting stage-3 (i686) I still get the same error message when
trying to compile kernel:
CC scripts/mod/empty.o
cc1: error: CPU you selected does not support x86-64 instruction set
make[1]: *** [scripts/Makefile.build:266: scripts/mod/empty.o] Error 1
make: *** [Makefile:1137: prepare0] Error 2
The CPU I have:
AMD FX(tm)-8150 Eight-Core Processor
make.conf
COMMON_FLAGS="-march=native -O2 -pipe"
#COMMON_FLAGS="-O2 -march=i686 -pipe"
CFLAGS="${COMMON_FLAGS}"
CXXFLAGS="${COMMON_FLAGS}"
FCFLAGS="${COMMON_FLAGS}"
FFLAGS="${COMMON_FLAGS}"
CPU_FLAGS_X86="mmx mmxext sse sse2 sse3"
Re: [gentoo-user] CPU you selected does not support x86-64 instruction set
On 12/14/2020 11:50 PM, J. Roeleveld wrote: > On Tuesday, December 15, 2020 7:17:57 AM CET the...@sys-concept.com wrote: >> On 12/14/2020 06:21 PM, the...@sys-concept.com wrote: >>> By mistake on new installation I untar wrong: stage-3 x86_64 instead of >>> i686 >>> >>> during kernel compiling I got: >>> cc1: error: CPU you selected does not support x86-64 instruction set >>> >>> Is it possible to untar new stage-3 (i686) over current one, or I need >>> to delete all the folders? >> >> After selecting stage-3 (i686) I still get the same error message when >> trying to compile kernel: >> >> CC scripts/mod/empty.o >> cc1: error: CPU you selected does not support x86-64 instruction set >> make[1]: *** [scripts/Makefile.build:266: scripts/mod/empty.o] Error 1 >> make: *** [Makefile:1137: prepare0] Error 2 >> >> The CPU I have: >> AMD FX(tm)-8150 Eight-Core Processor > > Isn't this a 64-bit CPU? > If you boot using a 64bit live-image (the gentoo-admin ISO as an example), > you > should be able to actually use 64bit. > > -- > Joost I'm confused as well, setting from make.conf on this CPU with previous kernel was: CHOST="x86_64-pc-linux-gnu"
Re: [gentoo-user] Upgrade an old system
[snip] emerge --update --oneshot portage !!! All ebuilds that could satisfy ">=app-crypt/openpgp-keys-gentoo-release-20180706" have been masked. !!! One of the following masked packages is required to complete your request: - app-crypt/openpgp-keys-gentoo-release-20200704::gentoo (masked by: EAPI 7) The current version of portage supports EAPI '6'. You must upgrade to a newer version of portage before EAPI masked packages can be installed. (dependency required by "sys-apps/portage-2.3.99-r2::gentoo[rsync-verify,-build]" [ebuild]) (dependency required by "portage" [argument]) I don't even have "app-crypt/openpgp-keys-gentoo-release" installed why is it complaining?
Re: [gentoo-user] system won't boot - --no-bootloader set; Skipping bootloader update ...
On 12/11/2020 07:07 AM, the...@sys-concept.com wrote: [snip] >>> >>> I bootstrap the PC and run: genkernel --menuconfig all >>> and finish compiling, and I get a message: >>> - >>> * Kernel compiled successfully! >>> * >>> * --no-bootloader set; Skipping bootloader update ... >>> * >>> * Required kernel parameter: >>> * >>> * root=/dev/$ROOT >>> * >>> * Where $ROOT is the device node for your root partition as the >>> * one specified in /etc/fstab >>> --- >>> >>> What went wrong? >>> >>> Here is my fstab: >>> LABEL=boot /boot vfat noauto,noatime 1 2 >>> UUID=d32946b3-2236-4998-80dd-68b7d78e0c7b / ext4 noatime >>> 0 1 >>> LABEL=swap none swap sw 0 0 > > Now, when I boot I get a message: > > Block device UUID=d32946b3-2236-4998-80dd-68b7d78e0c7b is not a valid > root device. > > I did not change anything in /etc/fstab blkid /dev/nvme0n1p4 /dev/nvme0n1p4: UUID="d32946b3-2236-4998-80dd-68b7d78e0c7b" BLOCK_SIZE="4096" TYPE="ext4" PARTLABEL="rootfs" PARTUUID="17f9927c-a792-41fc-bff3-a50c420ee616" So why boot can not find "/" partition ???
[gentoo-user] switching from "refine" to "grub"
I use refine as boot loader but it is giving me a problems. How to switch back to grub 2 And remove any refine files from /boot
[gentoo-user] CPU you selected does not support x86-64 instruction set
By mistake on new installation I untar wrong: stage-3 x86_64 instead of i686 during kernel compiling I got: cc1: error: CPU you selected does not support x86-64 instruction set Is it possible to untar new stage-3 (i686) over current one, or I need to delete all the folders?
Re: [gentoo-user] Upgrade an old system
On 12/14/2020 12:52 PM, Arve Barsnes wrote: > On Mon, 14 Dec 2020 at 20:38, wrote: >> but that portage "portage-20090720.tar.bz2" seems old; what is the >> latest one? > > They're generated every day, so pick your poison. Notice it mentions > updating the portage tree 3-4 months at a time, so just pick some > dates at reasonable intervals from your starting point. > > Regards, > Arve Looking at this directory: https://github.com/gentoo/portage/releases/tag/portage-3.0.12 file: portage-portage-3.0.12.tar.gz has totally different structure If I run: tar xzf portage-portage-3.0.12.tar.gz -C /usr it will create directory /usr/portage-portage-3.0.12 emerge --update --oneshot portage can not fine it as it is looking for /usr/portage
Re: [gentoo-user] nouveau: gr: failed to load firmware "gr/sw_nonctx"
On 12/14/2020 02:03 AM, Michael wrote: > On Monday, 14 December 2020 00:27:03 GMT the...@sys-concept.com wrote: >> On 12/13/2020 04:44 PM, Michael wrote: >>> On Sunday, 13 December 2020 18:52:51 GMT the...@sys-concept.com wrote: I have "nouveau" build into kernel but it doesn't work: Fom dmesg: nouveau :08:00.0: NVIDIA GP107 (137000a1) nouveau :08:00.0: gr: failed to load firmware "gr/sw_nonctx" nouveau :08:00.0: gr: failed to load gr/sw_nonctx nouveau :08:00.0: DRM: failed to create kernel channel, -22 [snip] >> >> Both had same output, so why one kernel was working the other didn't? > > Were both of these kernels installed with a corresponding correctly > functioning initramfs, which had all the requisite files (including -- > firmware) to boot with, or only one of them did? > > Without an initramfs you will need to specify and build any requisite > firmware > blobs in the kernel image itself, so they are available to the system as it > boots up. Since I was able to make "nvidia" work I abandon fighting with installing/enabling "nouveau" Originally I wanted to have it as a backup switching between these two (just in case) but it is not an easy project.
Re: [gentoo-user] Re: Upgrade an old system
On 12/14/2020 02:55 PM, Grant Edwards wrote: > On 2020-12-14, the...@sys-concept.com wrote: >> I'm having similar problem as "n952162" upgrading an old (last updated >> 1.8-year ago) > > If I were youe, I'd just reinstall after 1.8 years. Updating is going > to take way, way more work. > > -- > Grant I was thinking the same thing. But I'll try first if its possible to upgrade.
Re: [gentoo-user] Upgrade an old system
On 12/14/2020 02:58 PM, Arve Barsnes wrote: > On Mon, 14 Dec 2020 at 22:20, wrote: >> Looking at this directory: >> https://github.com/gentoo/portage/releases/tag/portage-3.0.12 >> >> file: portage-portage-3.0.12.tar.gz has totally different structure >> If I run: tar xzf portage-portage-3.0.12.tar.gz -C /usr >> it will create directory /usr/portage-portage-3.0.12 > > That is a release of the portage *application*, you need snapshots of > the portage *tree*. > > I could find some a year old here: > https://mirrors.sohu.com/gentoo/snapshots/ > > You might need to look for even older ones, but worth a try. > > Regards, > Arve Moving forward like a snail. Unmerged portage to local directory and running: ./portage-portage-3.0.12/bin/emerge -1 portage gives me two blockers: [blocks B ]
[gentoo-user] nouveau: gr: failed to load firmware "gr/sw_nonctx"
I have "nouveau" build into kernel but it doesn't work: Fom dmesg: nouveau :08:00.0: NVIDIA GP107 (137000a1) nouveau :08:00.0: gr: failed to load firmware "gr/sw_nonctx" nouveau :08:00.0: gr: failed to load gr/sw_nonctx nouveau :08:00.0: DRM: failed to create kernel channel, -22 grep -i nouveau .config CONFIG_DRM_NOUVEAU=y # CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT is not set CONFIG_NOUVEAU_DEBUG=5 CONFIG_NOUVEAU_DEBUG_DEFAULT=3 # CONFIG_NOUVEAU_DEBUG_MMU is not set CONFIG_DRM_NOUVEAU_BACKLIGHT=y I have "linux-firmware" installed but there is a "?" mark beside it eix linux-firmware [?] sys-kernel/linux-firmware Installed versions: 20201022-r3
Re: [gentoo-user] nouveau: gr: failed to load firmware "gr/sw_nonctx"
On 12/13/2020 04:33 PM, Neil Bothwick wrote:
> On Sun, 13 Dec 2020 11:52:51 -0700, the...@sys-concept.com wrote:
>
>> I have "linux-firmware" installed but there is a "?" mark beside it
>>
>> eix linux-firmware
>> [?] sys-kernel/linux-firmware
>> Installed versions: 20201022-r3
>>
> It means the version you have installed is no longer in the tree. You
> should update to the latest.
>
Something is wrong, I just --sync and reinstall linux-firmware but the output
is still the same:
eix linux-firmware
[?] sys-kernel/linux-firmware
Available versions: 20200316^bsd 20200421^bsd 20200519^bsd 20200619^bsd
20200721^bsd 20200817^bsd 20200918^bsd 20201022-r2^bstd ***l^bstd
{initramfs +redistributable savedconfig unknown-license}
Installed versions: 20201022-r3^bst(05:30:05 PM
12/13/2020)(redistributable -initramfs -savedconfig -unknown-license)
Homepage:
https://git.kernel.org/?p=linux/kernel/git/firmware/linux-firmware.git
Description: Linux firmware files
[gentoo-user] grub-install: warning: File system `ext2' doesn't support embedding.
I removed "vfat" boot partition and created/change it to ext2 But now when i try to install grub: grub-install /dev/nvme0n1p2 Installing for i386-pc platform. grub-install: warning: File system `ext2' doesn't support embedding. grub-install: warning: Embedding is not possible. GRUB can only be installed in this setup by using blocklists. However, blocklists are UNRELIABLE and their use is discouraged.. grub-install: error: will not proceed with blocklists. Is it something that is going to create problem?
Re: [gentoo-user] grub-install: warning: File system `ext2' doesn't support embedding.
On 12/13/2020 08:15 PM, the...@sys-concept.com wrote: > I removed "vfat" boot partition and created/change it to ext2 > > But now when i try to install grub: > > grub-install /dev/nvme0n1p2 > Installing for i386-pc platform. > grub-install: warning: File system `ext2' doesn't support embedding. > grub-install: warning: Embedding is not possible. GRUB can only be installed > in this setup by using blocklists. However, blocklists are UNRELIABLE and > their use is discouraged.. > grub-install: error: will not proceed with blocklists. > > Is it something that is going to create problem? After rebooting, the system can not find boot disk. fstab: /dev/nvme0n1p2 /boot ext2noauto,noatime 1 2 /dev/nvme0n1p4 / ext4noatime 0 1 /dev/nvme0n1p3 noneswapsw 0 0 fdisk -l /dev/nvme0n1p12048 6143 40962M BIOS boot /dev/nvme0n1p26144 268287 262144 128M EFI System /dev/nvme0n1p3 26828813168631048576 512M Linux filesystem /dev/nvme0n1p4 1316864 3907027119 3905710256 1.8T Linux filesystem Do I need to go to "vfat" for /boot partition? Why isn't it working?
Re: [gentoo-user] nouveau: gr: failed to load firmware "gr/sw_nonctx"
On 12/13/2020 04:44 PM, Michael wrote: > On Sunday, 13 December 2020 18:52:51 GMT the...@sys-concept.com wrote: >> I have "nouveau" build into kernel but it doesn't work: >> >> Fom dmesg: >> >> nouveau :08:00.0: NVIDIA GP107 (137000a1) >> nouveau :08:00.0: gr: failed to load firmware "gr/sw_nonctx" >> nouveau :08:00.0: gr: failed to load gr/sw_nonctx >> nouveau :08:00.0: DRM: failed to create kernel channel, -22 >> >> grep -i nouveau .config >> CONFIG_DRM_NOUVEAU=y >> # CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT is not set >> CONFIG_NOUVEAU_DEBUG=5 >> CONFIG_NOUVEAU_DEBUG_DEFAULT=3 >> # CONFIG_NOUVEAU_DEBUG_MMU is not set >> CONFIG_DRM_NOUVEAU_BACKLIGHT=y > > I've never used NVIDIA cards with Gentoo, but in firmware terms you need to > specify in your kernel what firmware you want installed in it. Have a look > at > this guide: > > https://wiki.gentoo.org/wiki/Nouveau/en > > and this: > > https://wiki.gentoo.org/wiki/Linux_firmware > > You'll need to add the firmware the video card asks for here: > > Device Drivers ---> > Generic Driver Options ---> > Firmware loader ---> >-*- Firmware loading facility >() Build named firmware blobs into the kernel binary <== > > In this instance your card NVIDIA GP107 should need '/lib/firmware/nvidia/ > gp107', so the respective entry for it in the kernel config ought to be: > > CONFIG_EXTRA_FIRMWARE="nvidia/gp107" > > Someone more clued up on these cards can correct me or add to it. Thank you, but I've managed to install "nvidia" following: https://wiki.gentoo.org/wiki/NVIDIA/nvidia-drivers What confused me is the output from two kernels: linux-5.4.80-gentoo-r1 was installed with: genkernel --menuconfig all and "nouveau" was working OK on that kernel: grep CONFIG_EXTRA_FIRMWARE ../linux-5.4.80-gentoo-r1/.config showing: CONFIG_EXTRA_FIRMWARE="" The one below was compiled manually: grep CONFIG_EXTRA_FIRMWARE ../linux-5.4.72-gentoo/.config CONFIG_EXTRA_FIRMWARE="" Both had same output, so why one kernel was working the other didn't?
[gentoo-user] nvidia: loading out-of-tree module taints kernel
I'm loading nvidia via: /etc/modules-load.d/video.conf but when kernel boots, there is a error message: Failed to load nvidia dmesg |grep nvidia nvidia: loading out-of-tree module taints kernel. nvidia: module license 'NVIDIA' taints kernel. nvidia-nvlink: Nvlink Core is being initialized, major device number 246 nvidia :08:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms 455.28 Wed Sep 30 00:58:12 UTC 2020 [drm] [nvidia-drm] [GPU ID 0x0800] Loading driver [drm] Initialized nvidia-drm 0.0.0 20160202 for :08:00.0 on minor 0 nvidia-smi (1442) used greatest stack depth: 12624 bytes left caller _nv000708rm+0x1af/0x200 [nvidia] mapping multiple BARs Why this error message?
Re: [gentoo-user] how to control "forcefsck"
On 12/13/2020 05:56 PM, the...@sys-concept.com wrote: > > After running in "/" directory: > touch forcefsck > > The file is gone now, but every time I reboot the system the root > partition goes into force check: > > fstab: > /dev/nvme0n1p4/ ext4noatime 0 1 > If I'm not mistaken it should be: tune2fs -c -1 /dev/nvme0n1p4 but why was the setting reset when I run "touch forcefsck"
Re: [gentoo-user] nvidia: loading out-of-tree module taints kernel
On 12/13/2020 05:48 PM, the...@sys-concept.com wrote: > I'm loading nvidia via: /etc/modules-load.d/video.conf > > but when kernel boots, there is a error message: > > Failed to load nvidia > > dmesg |grep nvidia > nvidia: loading out-of-tree module taints kernel. > nvidia: module license 'NVIDIA' taints kernel. > nvidia-nvlink: Nvlink Core is being initialized, major device number 246 > nvidia :08:00.0: vgaarb: changed VGA decodes: > olddecodes=io+mem,decodes=none:owns=io+mem > nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms > 455.28 Wed Sep 30 00:58:12 UTC 2020 > [drm] [nvidia-drm] [GPU ID 0x0800] Loading driver > [drm] Initialized nvidia-drm 0.0.0 20160202 for :08:00.0 on minor 0 > nvidia-smi (1442) used greatest stack depth: 12624 bytes left > caller _nv000708rm+0x1af/0x200 [nvidia] mapping multiple BARs > > Why this error message? and yes, I run: emerge -1 @module-rebuild
[gentoo-user] how to control "forcefsck"
After running in "/" directory: touch forcefsck The file is gone now, but every time I reboot the system the root partition goes into force check: fstab: /dev/nvme0n1p4 / ext4noatime 0 1
Re: [gentoo-user] grub-install: warning: File system `ext2' doesn't support embedding.
On 12/13/2020 08:28 PM, the...@sys-concept.com wrote: > On 12/13/2020 08:15 PM, the...@sys-concept.com wrote: >> I removed "vfat" boot partition and created/change it to ext2 >> >> But now when i try to install grub: >> >> grub-install /dev/nvme0n1p2 Simple mistake it should be: grub-install /dev/nvme0n1
Re: [gentoo-user] Re: grub-install: warning: File system `ext2' doesn't support embedding.
On 12/13/2020 09:05 PM, Grant Edwards wrote: > On 2020-12-14, the...@sys-concept.com wrote: > >> I removed "vfat" boot partition and created/change it to ext2 >> >> But now when i try to install grub: >> >> grub-install /dev/nvme0n1p2 >> Installing for i386-pc platform. >> grub-install: warning: File system `ext2' doesn't support embedding. >> grub-install: warning: Embedding is not possible. GRUB can only be >> installed in this setup by using blocklists. However, blocklists are >> UNRELIABLE and their use is discouraged.. >> grub-install: error: will not proceed with blocklists. >> >> Is it something that is going to create problem? > > If you want to install grub in an ext2 partition, you'll need to use > the --force option to get grub2 to use blocklists. After you've done > that, you need to make the critical file immutable so that it can't be > altered or moved: > > # chattr +i /boot/grub/i386-pc/core.img > > If you ever need to update grub, you'll have to unlock that file using > 'chattr -i'. > > -- > Grant I don't think so. I just tried made typo. Instead of running: grub-install /dev/nvme0n1 I did: grub-install /dev/nvme0n1p2 It install without any errors. I've not done any installation for some time, a lot had changed. It is a good practice as next PC will be a production PC; so I know to stay away from "vfat" in boot partition.
Re: [gentoo-user] system won't boot - --no-bootloader set; Skipping bootloader update ...
On 12/11/2020 10:45 AM, Michael wrote: > On Friday, 11 December 2020 16:42:08 GMT tedheadster wrote: >> On Fri, Dec 11, 2020 at 9:27 AM wrote: >>> On 12/11/2020 07:07 AM, the...@sys-concept.com wrote: Now, when I boot I get a message: Block device UUID=d32946b3-2236-4998-80dd-68b7d78e0c7b is not a valid root device. >>> >>> This puzzles me. I cannot find the string "is not a valid root device" (or >> >> sub-strings) in the source code for the Linux kernel, GRUB2, and refind. It >> seems to me it should be in one of them. >> >> - Matthew > > The error is indicative of the kernel driver for the / block device missing. > If it is not built in-the-kernel, but as a module, then it should be in > initramfs. > > Copy the kernel image, System.map, .config and corresponding initramfs to the > /boot partition, then point your boot manager to the kernel to boot it. How do you copy/generate initramfs in /boot directory?
Re: [gentoo-user] system won't boot - --no-bootloader set; Skipping bootloader update ...
On 12/11/2020 11:39 AM, Michael wrote: > On Friday, 11 December 2020 18:24:27 GMT the...@sys-concept.com wrote: >> On 12/11/2020 10:45 AM, Michael wrote: >>> On Friday, 11 December 2020 16:42:08 GMT tedheadster wrote: On Fri, Dec 11, 2020 at 9:27 AM wrote: > On 12/11/2020 07:07 AM, the...@sys-concept.com wrote: >> Now, when I boot I get a message: >> >> Block device UUID=d32946b3-2236-4998-80dd-68b7d78e0c7b is not a valid >> root device. > > This puzzles me. I cannot find the string "is not a valid root device" > (or sub-strings) in the source code for the Linux kernel, GRUB2, and refind. It seems to me it should be in one of them. - Matthew >>> >>> The error is indicative of the kernel driver for the / block device >>> missing. If it is not built in-the-kernel, but as a module, then it >>> should be in initramfs. >>> >>> Copy the kernel image, System.map, .config and corresponding initramfs to >>> the /boot partition, then point your boot manager to the kernel to boot >>> it. >> How do you copy/generate initramfs in /boot directory? > > https://wiki.gentoo.org/wiki/Handbook:AMD64/Installation/Kernel > https://wiki.gentoo.org/wiki/Genkernel > > If you're using genkernel it will copy it to /boot. Besides the Handbook you > may find the following reference material on boot managers/loaders useful: > > For rEFInd see here: > > https://wiki.gentoo.org/wiki/Refind > > For GRUB see here: > > https://wiki.gentoo.org/wiki/GRUB2 > > For efibootmgr see here: > > https://wiki.gentoo.org/wiki/Handbook:AMD64/Installation/ > Bootloader#Alternative_2:_efibootmgr After I compile kernel I usually get this message (WHY?): * You will find the initramfs in '/boot/initramfs-5.4.72-gentoo.img'. * WARNING... WARNING... WARNING... * Additional kernel parameters that *may* be required to boot properly: * * With support for several ext* filesystems available, it may be needed to * add "rootfstype=ext3" or "rootfstype=ext4" to the list of boot parameters.
Re: [gentoo-user] system won't boot - --no-bootloader set; Skipping bootloader update ...
On 12/11/2020 10:45 AM, Michael wrote: > On Friday, 11 December 2020 16:42:08 GMT tedheadster wrote: >> On Fri, Dec 11, 2020 at 9:27 AM wrote: >>> On 12/11/2020 07:07 AM, the...@sys-concept.com wrote: Now, when I boot I get a message: Block device UUID=d32946b3-2236-4998-80dd-68b7d78e0c7b is not a valid root device. >>> >>> This puzzles me. I cannot find the string "is not a valid root device" (or >> >> sub-strings) in the source code for the Linux kernel, GRUB2, and refind. It >> seems to me it should be in one of them. >> >> - Matthew > > The error is indicative of the kernel driver for the / block device missing. > If it is not built in-the-kernel, but as a module, then it should be in > initramfs. > > Copy the kernel image, System.map, .config and corresponding initramfs to the > /boot partition, then point your boot manager to the kernel to boot it. grep -i initramfs .config (not showing anything) CONFIG_INITRAMFS_SOURCE="" After cofiguring kernel, I run: make && make modules_install make install grub-install --target=x86_64-efi --efi-directory=/boot Installing for x86_64-efi platform. Installation finished. No error reported. grub-mkconfig -o /boot/grub/grub.cfg I'm using kernel: System.map-5.4.72-gentoo ll /boot/ total 56547 drwxr-xr-x 4 root root 512 Dec 11 08:23 EFI -rwxr-xr-x 1 root root 4730365 Dec 11 11:01 System.map-5.4.72-gentoo -rwxr-xr-x 1 root root 4618921 Dec 11 08:57 System.map-5.4.72-gentoo-x86_64 -rwxr-xr-x 1 root root 4451817 Dec 11 10:16 System.map-5.4.80-gentoo-r1-x86_64 -rwxr-xr-x 1 root root 121805 Dec 11 11:01 config-5.4.72-gentoo -rwxr-xr-x 1 root root 212517 Dec 11 06:18 config-5.4.72-gentoo-x86_64 -rwxr-xr-x 1 root root 121783 Dec 11 09:48 config-5.4.72-gentoo.old drwxr-xr-x 5 root root 512 Dec 11 11:11 grub -rwxr-xr-x 1 root root 3573416 Dec 11 08:59 initramfs-5.4.72-gentoo-x86_64.img -rwxr-xr-x 1 root root 10521824 Dec 11 10:26 initramfs-5.4.80-gentoo-r1-x86_64.img -rwxr-xr-x 1 root root 9991040 Dec 11 11:01 vmlinuz-5.4.72-gentoo -rwxr-xr-x 1 root root 9831296 Dec 11 08:57 vmlinuz-5.4.72-gentoo-x86_64 -rwxr-xr-x 1 root root 9726336 Dec 11 10:17 vmlinuz-5.4.80-gentoo-r1-x86_64 Doesn't matter which kernel I boot, the login is: "This is (none). unknown domain (none) longin: I can login as user but not as root. It seems to me it didn't boot correctly. Don't now what else to try.
[gentoo-user] kernel support for: i211 - intel network driver
I have Asus X570-pro MB with Intel I211-AT network When I compiled into the kernel (not as module) the "IGB" network driver but the network is not recognized. lsmod |grep igb is not showing anything. I think the above commend only show anything if I compile it as a module, isn't it? If I compile it into the kernel, it will not show anything. Anyhow, what driver should I use. -- Thelma
[gentoo-user] duplicate gentoo system
I'm looking for an idea to duplicate my old gentoo system. I'm using old programs that require older version php, ( PHP Version 5.6) the program is not compatible with newer php. 7.4 and apache 2.2 Gentoo is install on 1TB SSD (/dev/sda) The new 2TB SSD is M.2 (so it has a strange name) 1.) Is my option only: dd if=/dev/sdX of=/dev/sdY bs=64K conv=noerror,sync If I duplicate the drive this way I'll end-up with two partitions, as I'll have 1TB free on a new drive. Or is there a way to resize partition on M.2 SSD 2.) Another options, I could dig-out the old programs from "attic", but that will not be an easy job. -- Thelma
Re: [gentoo-user] duplicate gentoo system
On 11/17/2020 11:26 AM, Michael wrote: > On Tuesday, 17 November 2020 17:47:09 GMT the...@sys-concept.com wrote: >> I'm looking for an idea to duplicate my old gentoo system. >> I'm using old programs that require older version php, ( PHP Version >> 5.6) the program is not compatible with newer php. 7.4 and apache 2.2 >> >> Gentoo is install on 1TB SSD (/dev/sda) >> The new 2TB SSD is M.2 (so it has a strange name) >> >> 1.) Is my option only: >> dd if=/dev/sdX of=/dev/sdY bs=64K conv=noerror,sync >> >> If I duplicate the drive this way I'll end-up with two partitions, as >> I'll have 1TB free on a new drive. Or is there a way to resize >> partition on M.2 SSD >> >> 2.) Another options, I could dig-out the old programs from "attic", but >> that will not be an easy job. > > You could go about this in a number of different ways. > > dd command will take forever, as it is copying every bit and byte from one > disk to the next, whether it contains data or not. > > I prefer to use a clonezilla liveUSB to copy a disk or selected partitions > between disks, which will take significantly less time as only blocks with > data get copied over. > > You can increase the partition size after you finish copying it onto the new > disk and then the filesystem size within it. Gparted can run both steps in a > single stroke. > > If you prefer a more manual and tedious way, you can create a partition as > large as you need it to be on the new disk, format it with a filesystem of > choice, then use rsync or tar to copy over the files you want and --exclude > anything you don't want copied over. Thanks for the input, will try on the weekend.
Re: [gentoo-user] duplicate gentoo system
On 11/17/2020 11:26 AM, Michael wrote: > On Tuesday, 17 November 2020 17:47:09 GMT the...@sys-concept.com wrote: >> I'm looking for an idea to duplicate my old gentoo system. >> I'm using old programs that require older version php, ( PHP Version >> 5.6) the program is not compatible with newer php. 7.4 and apache 2.2 >> >> Gentoo is install on 1TB SSD (/dev/sda) >> The new 2TB SSD is M.2 (so it has a strange name) >> >> 1.) Is my option only: >> dd if=/dev/sdX of=/dev/sdY bs=64K conv=noerror,sync >> >> If I duplicate the drive this way I'll end-up with two partitions, as >> I'll have 1TB free on a new drive. Or is there a way to resize >> partition on M.2 SSD >> >> 2.) Another options, I could dig-out the old programs from "attic", but >> that will not be an easy job. > > You could go about this in a number of different ways. > > dd command will take forever, as it is copying every bit and byte from one > disk to the next, whether it contains data or not. > > I prefer to use a clonezilla liveUSB to copy a disk or selected partitions > between disks, which will take significantly less time as only blocks with > data get copied over. > > You can increase the partition size after you finish copying it onto the new > disk and then the filesystem size within it. Gparted can run both steps in a > single stroke. > > If you prefer a more manual and tedious way, you can create a partition as > large as you need it to be on the new disk, format it with a filesystem of > choice, then use rsync or tar to copy over the files you want and --exclude > anything you don't want copied over. Manual approach might be confusing and prone to errors. I will try Gparted as you suggested but I was wondering if it will allow me to combine/join partitions. On most modern system I think there is: 1 - boot partiton 2 - swap if needed 3 - root partition (where home is as well) My current layout is old one: dev/sda1/boot ext2 /dev/sda3 / ext4 /dev/sda2 noneswap /dev/sda4 /home ext4 Is it possible with Gparted combine "/" and "home" partitions, or is it as simple as coping all file from "home" partition to "/" home folder.
[gentoo-user] duplicate gentoo system - errors
OK, I used Gparted (Bootable usb) to copy partition from: Western Digital driver, usually: /dev/sda1 etc to M.2 SSD /dev/ nvme0n1p1 etc I can boot M.2 drive, but the x-server doesn't work (even though I use same graphical card). Network is not working (easy fix, new driver needs to be compiled IN) but there is a bigger problem. Duplicating was easy, but when I try to recompile a kernel I get an error: make menuconfig HOSTCC script/kconfig/mconf.o : internal compiler error: Illegal instruction Even if I try to run: emerge --info I get: Illegal instruction In addition my fstab doesn't look correct (but it works) /dev/sda1/bootext2 It should be something like: /dev/nvme0n1p1 /boot ext2 -- Thelma
Re: [gentoo-user] duplicate gentoo system - errors
On 11/22/2020 05:25 PM, Michael wrote: > On Sunday, 22 November 2020 23:39:44 GMT the...@sys-concept.com wrote: >> OK, I used Gparted (Bootable usb) to copy partition from: >> Western Digital driver, usually: >> /dev/sda1 etc >> >> to M.2 SSD >> /dev/ nvme0n1p1 etc >> >> I can boot M.2 drive, but the x-server doesn't work (even though I use >> same graphical card). Network is not working (easy fix, new driver >> needs to be compiled IN) but there is a bigger problem. > > If you have cloned each partition from the old to the new disk, then the new > disk should work exactly as the old disk does. I mean, it should have the > same kernel, the same / filesystem, the same modules, etc. > > Since the new disk is an nvme drive, you will need additional drivers - > should > these not be available in the old kernel. > > >> Duplicating was easy, but when I try to recompile a kernel I get an error: >> >> make menuconfig >> HOSTCC script/kconfig/mconf.o >> : internal compiler error: Illegal instruction >> >> Even if I try to run: emerge --info I get: >> Illegal instruction >> >> In addition my fstab doesn't look correct (but it works) >> /dev/sda1/bootext2 >> >> It should be something like: >> /dev/nvme0n1p1 /boot ext2 > > Do you have both disks connected to the MoBo when you're trying to boot from > the new disk? Yes, they are both connected > Have you changed the UUIDs on the new partitions? Never used UUID in fstab. Do I just run: blkid|grep UUID and copy it to fstab. > Have you installed the boot manager on the new disk (if using MBR)? I just copied the whole MBR to a new disk and it worked, the system boots, but nothing can be compiled.
Re: [gentoo-user] duplicate gentoo system - errors
On 11/22/2020 06:16 PM, Jack wrote: > On 2020.11.22 20:09, the...@sys-concept.com wrote: >> On 11/22/2020 05:25 PM, Michael wrote: >> > On Sunday, 22 November 2020 23:39:44 GMT the...@sys-concept.com wrote: >> >> OK, I used Gparted (Bootable usb) to copy partition from: >> >> Western Digital driver, usually: >> >> /dev/sda1 etc >> >> >> >> to M.2 SSD >> >> /dev/ nvme0n1p1 etc >> >> >> >> I can boot M.2 drive, but the x-server doesn't work (even though I use >> >> same graphical card). Network is not working (easy fix, new driver >> >> needs to be compiled IN) but there is a bigger problem. >> > >> > If you have cloned each partition from the old to the new disk, then >> the new >> > disk should work exactly as the old disk does. I mean, it should >> have the >> > same kernel, the same / filesystem, the same modules, etc. >> > >> > Since the new disk is an nvme drive, you will need additional >> drivers - should >> > these not be available in the old kernel. >> > >> > >> >> Duplicating was easy, but when I try to recompile a kernel I get an >> error: >> >> >> >> make menuconfig >> >> HOSTCC script/kconfig/mconf.o >> >> : internal compiler error: Illegal instruction >> >> >> >> Even if I try to run: emerge --info I get: >> >> Illegal instruction >> >> >> >> In addition my fstab doesn't look correct (but it works) >> >> /dev/sda1 /boot ext2 >> >> >> >> It should be something like: >> >> /dev/nvme0n1p1 /boot ext2 >> > >> > Do you have both disks connected to the MoBo when you're trying to >> boot from >> > the new disk? >> >> Yes, they are both connected >> >> > Have you changed the UUIDs on the new partitions? >> >> Never used UUID in fstab. Do I just run: blkid|grep UUID >> and copy it to fstab. >> >> > Have you installed the boot manager on the new disk (if using MBR)? >> >> I just copied the whole MBR to a new disk and it worked, the system >> boots, but nothing can be compiled. > I would confirm that you are really booted from the new disk and not the > old one. It is possible that the MBR from the new disk was used to > boot, but if /etc/fstab says /boot is mounted from /dev/sda1 then that > does seem wrong. I almost always put an empty file in the root of each > partition named for the disk/partition just so I can be sure what's > actually mounted. Is /etc/fstab identical on both disks? What does > fstab say about where / is mounted from? You are absolutely correct. I was booting the whole time the Western Digital (old drive). :-/ My mistake, once I removed the WD drive the new M.2 SSD doesn't even boot. I think the easiest way would be to re-install the Getnoo from scratch and dig out the old programs I need from "attic". Mixing/moving SSD (sda) and M2.2 (nvme0n1) and transferring partitions might not be as easy.
[gentoo-user] locating non utf-8 characters
I'm using sql-ledger and while making backup it uses stardard gzip program: $gzip = "gzip -S .gz"; The backup works with some dataset but one data set us giving me an error while trying to perform backup: Wide character in print at SL/AM.pm line 2044. Content-Type: application/file; Content-Disposition: attachment; filename=dataset_3-3.2.6-20201101.sql.gz ãù&ü_1604265628.dataset_3-3.2.6-20201101.sqlÏ\Yo;ñ~œØ – Since sql-ledger file are standard utf-8 files, I was thinking using: grep -axv '.*' file would find all not utf-8 characters. And it did. I use "nano" to remove them but I'm still getting the same error while performing backup. Any ideas? -- Thelma
[gentoo-user] Apache 2.4 can not access server subdirectory
After installing apache 2.4 I can not access server subdirectory: server/admin/index.html Forbiden You don't have permission to access /admin/index.html on this server I can access index.html in a directory below /admin (server/index.html) but not the server/admin/index.html I even change the permission on the index file: -rwxrwxrwx 1 apache apache 428 Oct 28 16:44 index.html I removed .htaccess from server/admin (it doesn't help) In apache.conf Options FollowSymLinks AllowOverride None Require all denied AllowOverride None Require all granted Options FollowSymLinks AllowOverride None Require all granted -- Thelma
Re: [gentoo-user] Apache 2.4 can not access server subdirectory
On 10/30/2020 04:31 AM, Michael wrote: [snip] >> >> This is from apache.conf >> >> >> Options FollowSymLinks >> AllowOverride None >> Require all denied >> >> >> >> AllowOverride None >> Require all granted >> >> >> >> Options FollowSymLinks >> AllowOverride All >> Require all granted >> >> >> I just search all server .htaccess files for "AllowOverride" but none is >> active in these files. >> grep -Rnw '/var/www/html/catalog/' -e 'AllowOverride' > > You wouldn't find "AllowOverride" within an .htaccess file. This is a > directive placed in the main /etc/apache2 configuration files to determine if > directives contained in local filesystem .htaccess files will be processed or > not. An 'AllowOverride None' will ignore .htaccess directives and make the > server speedier in responding to requests. TBH .htaccess are typically used > locally, when you are not allowed to make changes to the main apache > configuration files. Note, if you changed the name of ".htaccess" with the > 'AccessFileName' directive, you may end up missing it. > > Another thing to check is any changes to the default 'DirectoryIndex' types, > for the particular subdirectory. If you have removed index.html or > index.html.var in this directive then apache won't serve index files when a > directory like admin/ is requested. > > Finally, you could increase the log verbosity to debug level and see if more > information is revealed as to the cause of this problem. I have a bigger problem. The apache 2.4 doesn't read configuration files. In apache2.conf I have: # Include the virtual host configurations: IncludeOptional sites-enabled/*.conf So it should read read every *config file in sites-enabled/ In that directory I have: ll sites-enabled/ lrwxrwxrwx 1 root root 35 Oct 27 21:15 000-default.conf -> ../sites-available/000-default.conf -rw-r--r-- 1 root root 3420 Oct 29 18:03 vhosts.conf vhosts.conf - define my web-site, but I commented everything out in that file (it is empty) and restarted apache: /etc/init.d/apache2 restart And I can still display my web page. How is it possible???
Re: [gentoo-user] Apache 2.4 can not access server subdirectory
On 10/29/2020 06:21 AM, Remco Rijnders wrote: > On Wed, Oct 28, 2020 at 10:36:12PM -0600, thelma wrote in > <7b3d3416-77b0-02eb-ad05-f717fdf0b...@sys-concept.com>: >> After installing apache 2.4 I can not access server subdirectory: >> server/admin/index.html >> >> Forbiden >> You don't have permission to access /admin/index.html on this server >> >> I can access index.html in a directory below /admin (server/index.html) >> but not the server/admin/index.html > > That seems to suggest that either the permissions or ownership of > admin/index.html are different from admin/server/index.html, or that > there is a > difference of that kind between the directories admin/ and admin/server. > Are > they? Here are the permissions: index on server/ -rw-r--r-- 1 root root19078 Jan 14 2011 index.php index on server/admin/ drwxr-xr-x 6 root root 4096 Oct 28 22:08 admin -rwxrwxrwx 1 apache apache 428 Oct 28 16:44 index.html It works on Apache 2.2 but not Apache 2.4
Re: [gentoo-user] Apache 2.4 can not access server subdirectory
On 10/30/2020 11:55 AM, Michael wrote: > On Friday, 30 October 2020 16:27:05 GMT the...@sys-concept.com wrote: > >> I have a bigger problem. >> The apache 2.4 doesn't read configuration files. >> In apache2.conf I have: >> >> # Include the virtual host configurations: >> IncludeOptional sites-enabled/*.conf >> >> So it should read read every *config file in sites-enabled/ >> In that directory I have: >> >> ll sites-enabled/ >> lrwxrwxrwx 1 root root 35 Oct 27 21:15 000-default.conf -> >> ../sites-available/000-default.conf >> -rw-r--r-- 1 root root 3420 Oct 29 18:03 vhosts.conf > > I have different configuration files, one for each website. This makes it > easier to know where to look and what to edit when I want to make changes. > > >> vhosts.conf - define my web-site, but I commented everything out in that >> file (it is empty) and restarted apache: >> /etc/init.d/apache2 restart >> >> And I can still display my web page. >> How is it possible??? > > I would assume it is possible to still display your website because the main > apache2.conf and/or ./sites-available/000-default.conf contain some default > settings which specify the DocumentRoot where your website filesystem resides. > > Your approach to start from first principles by commenting out individual > configurations is sound, because you can check in this way what works and > what > does not. I check all configuration files for "DocumentRoot" and all the files have DocumentRoot commented out (so nothing is active) grep -Rnw '/etc/apache2/' -e 'DocumentRoot' Restarted apache 2.4 and the web-page is still loading :-/
[gentoo-user] Apache 2.4 .htaccess allows access
My server box ip is 10.0.0.109 In my .htaccess file I've tried Require all denied /RequireAll> I can still access the server I tried: Require all denied No difference, it allow me to access the server, and I know apache reads the .htaccess file -- Thelma
Re:[SOLVED] [gentoo-user] Apache 2.4 can not access server subdirectory
On 10/30/2020 12:34 PM, Michael wrote: [snip] vhosts.conf - define my web-site, but I commented everything out in that file (it is empty) and restarted apache: /etc/init.d/apache2 restart And I can still display my web page. How is it possible??? >>> >>> I would assume it is possible to still display your website because the >>> main apache2.conf and/or ./sites-available/000-default.conf contain some >>> default settings which specify the DocumentRoot where your website >>> filesystem resides. >>> >>> Your approach to start from first principles by commenting out individual >>> configurations is sound, because you can check in this way what works and >>> what does not. >> >> I check all configuration files for "DocumentRoot" and all the files >> have DocumentRoot commented out (so nothing is active) >> grep -Rnw '/etc/apache2/' -e 'DocumentRoot' >> >> Restarted apache 2.4 and the web-page is still loading :-/ > > ServerRoot specified somewhere? Increase log verbosity and see what it > reports, otherwise I'm out of ideas! Solved. For some reason or another in my /etc/hosts file I had: 10.0.0.112 server.ca And apache was accessing my production box1 box1 - production box2 - work in progress I changed in hosts to: 10.0.0.112 www.server.ca And apache was resolving accessing box2 only. Strange.
Re: [gentoo-user] Apache 2.4 can not access server subdirectory
On 10/29/2020 10:53 AM, Michael wrote: > On Thursday, 29 October 2020 14:10:07 GMT the...@sys-concept.com wrote: >> On 10/29/2020 06:21 AM, Remco Rijnders wrote: >>> On Wed, Oct 28, 2020 at 10:36:12PM -0600, thelma wrote in >>> >>> <7b3d3416-77b0-02eb-ad05-f717fdf0b...@sys-concept.com>: >>>> After installing apache 2.4 I can not access server subdirectory: >>>> server/admin/index.html >>>> >>>> Forbiden >>>> You don't have permission to access /admin/index.html on this server >>>> >>>> I can access index.html in a directory below /admin (server/index.html) >>>> but not the server/admin/index.html >>> >>> That seems to suggest that either the permissions or ownership of >>> admin/index.html are different from admin/server/index.html, or that >>> there is a >>> difference of that kind between the directories admin/ and admin/server. >>> Are >>> they? >> >> Here are the permissions: >> >> index on server/ >> -rw-r--r-- 1 root root19078 Jan 14 2011 index.php > > The above is a .php file. Yes, it is and I can read that file. The files that I can not access are in: server/admin/index.html > > >> index on server/admin/ >> drwxr-xr-x 6 root root 4096 Oct 28 22:08 admin >> -rwxrwxrwx 1 apache apache 428 Oct 28 16:44 index.html > > You shouldn't need apache:apache or 0777 ownership of this file which is very > insecure, unless apache is meant to be editing it live. Normally root:root > and 0755 is what is used. Yes, I'll change that. I just use it temporarily as I run out of ideas to try :-/ > > Is 'server/' a subdirectory of '/var/www/'? Yes > .htaccess won't work if you have disabled it with 'AllowOverride None'. Thank you for the pointer. I just change this directive in apache.conf for /var/www/ and restarted apache but there is no difference. I still can not access /server/admin/ directory from apache. server = /var/www/html/catalog/ This is from apache.conf Options FollowSymLinks AllowOverride None Require all denied AllowOverride None Require all granted Options FollowSymLinks AllowOverride All Require all granted I just search all server .htaccess files for "AllowOverride" but none is active in these files. grep -Rnw '/var/www/html/catalog/' -e 'AllowOverride' > >> It works on Apache 2.2 but not Apache 2.4 > > Directives changed on version 2.4. It would be worth familiarising yourself > with the latest: > > https://httpd.apache.org/docs/2.4/upgrading.html >
[gentoo-user] x2go server - Connection failed. /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db:
I just installed x2goserver-4.1.0.2 (fuse sqlite -postgres) and I'm getting an error trying to connect to the server: Connection failed. /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db: syntax error in expression (error token is "::SQLite::db") Unable to find free display port or insert new session into database; parameters: port (50), hostname (syscon7) and session name (). The server starts without any errors but client can not connect to it.
Re: [gentoo-user] x2go server - Connection failed. /usr/lib64/x2go/x2gocheckport: line 131: DBD::SQLite::db:
On 12/30/2020 02:10 PM, the...@sys-concept.com wrote: > I just installed x2goserver-4.1.0.2 (fuse sqlite -postgres) and I'm > getting an error trying to connect to the server: I've missed the find print: x2godbadmin --createdb
[gentoo-user] x2goserver - very slow
The current x2goserver-4.1.0.2 is very, very slow. I am still runing older x2goserver-4.0.1.22 and the speed is OK but the current one 4.1.0.2 is very slow over local LAN regardless of the setting I use.
Re: [gentoo-user] Apache 2.4 - set SecStatusEngine to On
Thelma On 1/3/21 9:02 AM, Michael wrote: > On Saturday, 2 January 2021 04:46:58 GMT the...@sys-concept.com wrote: >> Status engine is currently disabled, enable it by set SecStatusEngine to On. >> >> How to enable "SecStatusEngine to On" in Apache 2.4 >> >> From my log file: >> [Fri Jan 01 19:44:52.649498 2021] [core:notice] [pid 14152] AH00094: >> Command line: '/usr/sbin/apache2 -D DEFAULT_VHOST -D INFO -D SSL -D >> SSL_DEFAULT_VHOST -D LANGUAGE -D PHP -D SECURITY -d /usr/lib64/apache2 >> -f /etc/apache2/httpd.conf' >> [Fri Jan 01 21:10:26.781254 2021] [mpm_prefork:notice] [pid 14152] >> AH00169: caught SIGTERM, shutting down >> [Fri Jan 01 21:10:27.871561 2021] [:notice] [pid 16586] ModSecurity for >> Apache/2.9.3 (http://www.modsecurity.org/) configured. >> [Fri Jan 01 21:10:27.871577 2021] [:notice] [pid 16586] ModSecurity: APR >> compiled version="1.7.0"; loaded version="1.7.0" >> [Fri Jan 01 21:10:27.871579 2021] [:notice] [pid 16586] ModSecurity: >> PCRE compiled version="8.44 "; loaded version="8.44 2020-02-12" >> [Fri Jan 01 21:10:27.871581 2021] [:notice] [pid 16586] ModSecurity: >> LIBXML compiled version="2.9.10" >> [Fri Jan 01 21:10:27.871582 2021] [:notice] [pid 16586] ModSecurity: >> Status engine is currently disabled, enable it by set SecStatusEngine to On. > > I would think you set it on in the config file for your vhost. I don't use > this function, but there are instructions how to configure it here: > > https://github.com/SpiderLabs/ModSecurity/wiki > > HTH. Adding: SecStatusEngine On to: 79_mod_security.conf solved the problem, the error message went away, but I'm puzzled why these messages appear in file: error_log these are not error logs just information.
Re: [gentoo-user] Thunderbird - Unable to save your message as a draft.
On 1/5/21 1:16 PM, antlists wrote: > On 04/01/2021 20:18, the...@sys-concept.com wrote: >> With Thunderbird-78.6.0 I'm getting an error message when composing messages: >> >> Unable to save your message as a draft. >> Sending of the message failed. >> >> What is the solution? I've run onto few of them but they are mostly for >> Windows users not really applicable to Linux. >> > Is your drafts folder on a network? Is the network available? I've hit that > problem a few times. > > Cheers, > Wol No, it was on a local computer. I restore emails from old computer (lost one day of emails) and now it is working. But I don't know what had happened. I've tried to restore only specific folders "Drafts" from old computer but it did not help, so it must have had something to do with other configuration. I've notices others had similar issues but solution is not standard across as TB has different menu layout through out platforms and versions. They are making it hard to configure it. As an example is a line wrapping, and old version of TB had this under "Option" menu (I think); now they hide it it some obscure configuration menu under "Edit --> Preferences --> General)
Re: [gentoo-user] resizing and moving home directory to new partition on save drive
On 1/10/21 3:46 PM, antlists wrote: > On 10/01/2021 21:42, the...@sys-concept.com wrote: >> I want to move /home directory to a new partition (save drive). >> >> I have 1-SSD drive: >> Filesystem Size Used Avail Use% >> /dev/sda4 916G 405G 464G 47% / >> >> >> Home directory is on it taking about 360GB >> >> I was planning doing it in stages. >> >> Stage-1 >> Using Gparted to resize "/" portion shirk it to about 450GB >> create new ext4 partition for /home /dev/sda5 >> >> Boot-strap the PC with live-gentoo >> mv /home /home.org >> mkdir /home >> mount ext4 /dev/sda5 /home/ >> >> cp -rp /home.org/* /home/ >> >> edit fstab: >> /dev/sda5 /home ext4 default 0 0 >> reboot and test home >> >> Am I missing something? > > Couple of things. > > Firstly, why use a gentoo live disk? Just log in as root. > > Secondly, why rename home? Just mount sda5 on /mnt to do the move, then add > it to fstab to mount on /home. > > And a little bit you might have missed - DON'T put root's home on a mounted > disk - if it's currently in /home, move it to /. Don't forget to edit > /etc/passwd if you have to move it. Can you elaborate pls.? My current "home" is in "/"; so why move it there, it is already there. I don't have extra disk around, but I could copy /home over network to another PC. I was planning to move "home" to another partition as I plan to wipe old installation (it is impossible for me to upgrade); it will be easier to reinstall. My old installation is: Portage 2.3.24 (python 3.5.4-final-0, default/linux/amd64/17.0/desktop, gcc-6.4.0, glibc-2.25-r10, 4.9.72-gentoo x86_64) Since, old installation has home or "/" (root) partition, if I wipe the root, home will be gone as well. So I was planning on moving "home" to another partition, this way all data will be there. So, after moving "home" to another partition "sda5" I can wipe the "sda4" and re-install gentoo. "home" data would not be touched by upgrade.
Re: [gentoo-user] resizing and moving home directory to new partition on save drive
On 1/10/21 6:57 PM, Wols Lists wrote: > On 11/01/21 00:31, the...@sys-concept.com wrote: >> On 1/10/21 3:46 PM, antlists wrote: >>> On 10/01/2021 21:42, the...@sys-concept.com wrote: I want to move /home directory to a new partition (save drive). I have 1-SSD drive: Filesystem Size Used Avail Use% /dev/sda4 916G 405G 464G 47% / Home directory is on it taking about 360GB I was planning doing it in stages. Stage-1 Using Gparted to resize "/" portion shirk it to about 450GB create new ext4 partition for /home /dev/sda5 Boot-strap the PC with live-gentoo mv /home /home.org mkdir /home mount ext4 /dev/sda5 /home/ cp -rp /home.org/* /home/ edit fstab: /dev/sda5/homeext4default 0 0 reboot and test home Am I missing something? >>> >>> Couple of things. >>> >>> Firstly, why use a gentoo live disk? Just log in as root. >>> >>> Secondly, why rename home? Just mount sda5 on /mnt to do the move, then add >>> it to fstab to mount on /home. >>> >>> And a little bit you might have missed - DON'T put root's home on a mounted >>> disk - if it's currently in /home, move it to /. Don't forget to edit >>> /etc/passwd if you have to move it. >> >> Can you elaborate pls.? >> My current "home" is in "/"; so why move it there, it is already there. >> I don't have extra disk around, but I could copy /home over network to >> another PC. > > Are you logging in as root?! THAT'S DANGEROUS! > > Probably not, you are probably misunderstanding me. > > I've just checked, on my system, root's home is /root, which is as it > should be. Is your home /home/username, or is it /username? You make it > sound like it's /username, which I don't think is what you mean ... >> >> I was planning to move "home" to another partition as I plan to wipe old >> installation (it is impossible for me to upgrade); it will be easier to >> reinstall. >> My old installation is: >> Portage 2.3.24 (python 3.5.4-final-0, default/linux/amd64/17.0/desktop, >> gcc-6.4.0, glibc-2.25-r10, 4.9.72-gentoo x86_64) >> >> Since, old installation has home or "/" (root) partition, if I wipe the >> root, home will be gone as well. So I was planning on moving "home" to >> another partition, this way all data will be there. >> So, after moving "home" to another partition "sda5" I can wipe the "sda4" >> and re-install gentoo. "home" data would not be touched by upgrade. >> >> > Ahh ... you didn't say that! That changes everything! > > Okay. I would look to free about 380GB (just enough) at the end of the > disk to create sda5 which will be (at least temporarily) your new /home. > LOGGED IN AS ROOT just mount that on /mnt, and copy the contents of > /home into it. > > Now using your gentoo install disk delete sda4 and split it into two - > your new sda4 for your new gentoo, and a new sda5 (AT LEAST as big as > one you created in the last step), which will shunt the partition you > just created into sda6. Install your new gentoo. > > Now you've got sda4 (/), sda5 (which will be /home), and sda6 (where > you've just copied your old /home). Mount sda6 on /mnt again, and copy > it to /home (sda5). > > Finally, delete sda6, extend sda5 to use the space you've just freed, > and expand the filesystem on /home to use the full size of the extended > partition. > > That'll probably leave you with a 150GB /root, but that'll be plenty I > expect (and a 760GB /home). > > Cheers, > Wol > Thank you, that will work too!
[gentoo-user] resizing and moving home directory to new partition on save drive
I want to move /home directory to a new partition (save drive). I have 1-SSD drive: Filesystem Size Used Avail Use% /dev/sda4 916G 405G 464G 47% / Home directory is on it taking about 360GB I was planning doing it in stages. Stage-1 Using Gparted to resize "/" portion shirk it to about 450GB create new ext4 partition for /home /dev/sda5 Boot-strap the PC with live-gentoo mv /home /home.org mkdir /home mount ext4 /dev/sda5 /home/ cp -rp /home.org/* /home/ edit fstab: /dev/sda5 /home ext4default 0 0 reboot and test home Am I missing something? If everything works, remove /home.org Stage-2: With Gparted resize both root and home portion, giving root about 200GB and rest to /home (dev/sda5)
Re: [gentoo-user] resizing and moving home directory to new partition on same drive
On 1/10/21 9:26 PM, Adam Carter wrote: >> >> Can I use "nano" to edit /etc/password file >> > > Yes, but it's generally safest to use usermod. When I try to use usermod -d /mnt/home/thelma -m thelma I get: usermod: user thelma is currently used by process 3037 Do I need to boot strap for this to work?
Re: [gentoo-user] resizing and moving home directory to new partition on same drive
On 1/10/21 3:46 PM, antlists wrote: > And a little bit you might have missed - DON'T put root's home on a mounted > disk - if it's currently in /home, move it to /. Don't forget to edit > /etc/passwd if you have to move it. Can I use "nano" to edit /etc/password file all I need to change is the user:x:1000:1000::/home/user:/bin/bash to: user:x:1000:1000::/mnt/home/user:/bin/bash Or I need to use: "vipw -s"
Re: [gentoo-user] network transfer speed
On 1/15/21 9:55 AM, Jack wrote: [snip] I don't know where does the file he sync from. If you sync a file from a server in other city, for a 20 to 22MB/s speed is very normal. But if in home, that is not good. And for ftp and rsync. ftp is better for transferring a single large file once. rsync is better for a long-term, incremental synchronization. The file verification of rsync may take a lot of time for first sync. >>> There is a theoretical network speed as already mentioned. There is a >>> protocol speed, which may limit throughput if it has e.g. heavy encryption/ >>> compression and the CPU is anaemic. Finally, there is a MoBo bus >>> (SCSI/SATA/ >>> USB) and the media storage limit. If using USB 1.1 or 2.0 and/or the disks >>> are slow or experience write amplification, you'll find this will constrain >>> the final transfer speed significantly. >> The computers on this network are 2-meters apart and they both use SSD Drive >> (so USB limitation doesn't come under consideration). >> Like I said, on my home network when I transfer the 24GB file I get about >> 110MiBps transfer, so I was expecting the same in remote location). >> Some units are connected to a router Ausus RT-AC66U B1 but these ports are >> gigabit too. > When you say the computers are remote, is it possible the file is passing > through your local computer on the way between the two remote machines? > Where are you actually running the rsync command? The fact that I'm logged via ssh over VPN to a remote network should not have any influence over network speed. I just made a loop: Network A ==> Internet ==> Network B ssh back to Network A over internet and run "rsync" I got same speed (as if I run the command locally) on Network A 112MB/s So the limiting factor is somewhere else.
Re: [gentoo-user] network transfer speed
On 1/15/21 1:11 AM, Raffaele BELARDI wrote: >> -Original Message- >> From: the...@sys-concept.com >> Sent: Friday, January 15, 2021 07:57 >> To: Gentoo mailing list >> Subject: [gentoo-user] network transfer speed >> >> >> On both of my systems the network card speed is showing 1000 >> cat /sys/class/net/enp4s0/speed 1000 >> >> but when I do rsync larage file I only see about: 20 to 22MB/s On my home >> network I get about 110MB/s between PC's >> >> Both PC's have SSD and the swith is Gigabit (I think). >> How to find a the bottleneck? > > If the PCs attached to the switch show 1000 then the switch _is_ gigabit. > > On my 1Gb home network I have an FTP transfer speed between Gentoo PCs A and > B of almost 900Mbps, the other way round is almost half of that. One > difference between the two systems is the disk, A uses SATA-2 disk while B > has SATA-3. > > Does the 'B' in 110MB/s stand for byte? If so you have 880Mbps which is not > bad, the problem probably lies somewhere else. Otherwise you could check the > switch error count (if you have a managed switch) or the network card error > count, just to ensure you don't have a cabling/connector problem. > > Have you tried other transfer methods just for comparison? I think FTP is > still the fastest way to transfer files, though insecure or inconvenient as > it might be. I have no experience with rsync. > > raffaele On a remote network I run ethtool on both cards and I got both 1000Mb/s speed 1.) ethtool net0 Settings for net0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on MDI-X: on (auto) 2.) ethtool enp4s0 Settings for enp4s0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: on (auto)
Re: [gentoo-user] network transfer speed
On 1/19/21 12:46 AM, Raffaele BELARDI wrote: >> -Original Message- >> From: the...@sys-concept.com >> Sent: Monday, January 18, 2021 20:13 >> To: gentoo-user@lists.gentoo.org >> Subject: Re: [gentoo-user] network transfer speed >> >> What switch would you folks recommend? >> I'm planning getting to the bottom of it including replacing switch and >> cable if >> I have to. > > At home I'm using Netgear GS305E/GS308E with no particular issue. The 'E' > stands for managed, I never use management features except for checking the > port status (nice to have, but LEDs give the same information) and in some > particular, business-related configuration, to enable port mirroring. I > haven't tried yet to set up a VLAN or configure QoS parameters, which I think > would be the main reason to prefer a managed over a non-managed. > Since I always used Netgear I can't say if they are better than others. > I think you are already aware that unless all cable patches are at least > CAT5e you're not going to get 1Gb speed. The 'e' here makes a real difference > over the plain CAT5. > > Raffaele That is a good hint, I need to check if it is CAT5 or CAT5e
Re: [gentoo-user] app-emulation/docker with Linode kernel
On 1/20/21 7:53 PM, Matt Connell (Gmail) wrote: > I use docker, on a Gentoo system, running on a Linode-hosted VPS, with > their kernel. I rely heavily on docker, with ~10 containers providing > various services at any given time. > > Lately, I've had a couple of incidents of the system becoming > unresponsive, and I believe it is docker-related. > > When I emerge docker, portage gives me the following warnings/errors: > >> * CONFIG_RT_GROUP_SCHED: is not set when it should be. >> * CONFIG_IPVLAN: is not set when it should be. >> * CONFIG_OVERLAY_FS_REDIRECT_DIR: should not be set. But it is. > > Could these complaints be a portent of what is causing the system to > become unresponsive? Is there anything I can do to resolve this when I > am using Linode's kernels? > > I know what to do when I am configuring and building my own kernel, but > on this system I'd prefer to avoid this if possible, since it is > Someone Else's Computer, after all. > > Any input is appreciated. Do you have access to their kernel .config file? If so just compile them IN and test it, make a backup of the current /boot kernel. I would say these should be compiled into the kernel. The first two are not compiled into my kernel and the third option is missing (no I'm not using docker)
Re: [gentoo-user] merged on \${HOST} with notice"
On 1/17/21 12:59 PM, Hogren wrote:
>
> On 17/01/2021 19:18, the...@sys-concept.com wrote:
>> I have in a new machine (as on all other boxes) in make.conf
>> PORTAGE_ELOG_MAILSUBJECT="package \${PACKAGE} merged on \${HOST} with notice"
>>
>> In /etc/conf.d/hostname
>> hostname="syscon3"
>>
>> But when a package is emerge I receive via email notice as in subject line:
>> "...merged on localhost.localdomain"
>> eg: package dev-vcs/git-2.26.2 merged on localhost.localdomain with notice
>>
>> Which file define "${HOST}"
>>
> Hello,
>
> I suppose you had already rebooted after modify the file ?
>
> Do you have Systemd ?
>
>
> Regards,
>
> Hogren
No, I did not rebooted the system. Do I need to?
I can not pin it down which file/setting it is.
When I receive emerge notice from my new system, both of them have "...merged
on localhost.localdomain" instead of "hostname" eg. syscon3 syscon7 etc.
Re: [gentoo-user] merged on \${HOST} with notice"
On 1/17/21 12:59 PM, Hogren wrote:
>
> On 17/01/2021 19:18, the...@sys-concept.com wrote:
>> I have in a new machine (as on all other boxes) in make.conf
>> PORTAGE_ELOG_MAILSUBJECT="package \${PACKAGE} merged on \${HOST} with notice"
>>
>> In /etc/conf.d/hostname
>> hostname="syscon3"
>>
>> But when a package is emerge I receive via email notice as in subject line:
>> "...merged on localhost.localdomain"
>> eg: package dev-vcs/git-2.26.2 merged on localhost.localdomain with notice
>>
>> Which file define "${HOST}"
>>
> Hello,
>
> I suppose you had already rebooted after modify the file ?
>
> Do you have Systemd ?
I forgot to mention, I use openrc
Re: [gentoo-user] merged on \${HOST} with notice"
On 1/17/21 2:04 PM, David Haller wrote:
> Hello,
>
> On Sun, 17 Jan 2021, the...@sys-concept.com wrote:
>> I have in a new machine (as on all other boxes) in make.conf
>> PORTAGE_ELOG_MAILSUBJECT="package \${PACKAGE} merged on \${HOST} with notice"
> [..]
>> Which file define "${HOST}"
>
> /etc/hosts
> [..]
> # IP-Address Full-Qualified-Hostname Short-Hostname
>
> 127.0.0.1 syscon3.domain.tld syscon3 localhost
> ::1 syscon3.domain.tld syscon3 localhost
>
>
> Use 'localdomain' as domain.tld if you don't have a domain.
>
> HTH,
> -dnh
THANK YOU! It is working.
Does placement of the name make a difference?
eg:
127.0.0.1 syscon3.domain.tld syscon3 localhost
vs.
127.0.0.1 localhost syscon3 syscon3.domain.tld
[gentoo-user] depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol
I'm compiling VirtualBox support into the latest kernel-5.4.80-gentoo-r1 [*] Virtualization ---> <*> Kernel-based Virtual Machine (KVM) support <*> KVM for AMD processors support And I get an error when compiling the kernel: make && make modules_install DEPMOD 5.4.80-gentoo-r1 depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_mmap depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_manager_func depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_device_release depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_kunmap depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_del_sub_from_lru depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_device_init depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_init_mm depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_dma_acc_size depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_tt_init depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_kmap depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_add_to_lru depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_init depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_validate depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_move_to_lru_tail depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_put depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_tt_fini depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol ttm_bo_eviction_valuable
Re: [gentoo-user] network transfer speed
On 1/15/21 9:00 PM, Adam Carter wrote: >> On a remote network I run ethtool on both cards and I got both 1000Mb/s >> speed >> >> > As the 20 odd MB/s you're getting is above what is possible on 100M > ethernet, you can rule out any ethernet interfaces at 100M. 1.) One Gentoo PC (that is about 20-30meters away from the switch) negotiated the speed of only 100 despite being capable of doing 1000. I'll have to buy a new switch and make a new CAT5e cable to test it. But but it will take some time. > Can you describe the network between the two systems with the slow transfer? 2.) The two Gentoo PC that are meters away from the switch are my concern firs. One is a server, another small PC run 24/7 and both negotiated speed of 1000 with the switch. I have to re-test the transfer speed between these to boxes first, and check to light on the switch if it is green and/or orange > If there is a fast WAN from one side of the globe to the other it could be > latency related. OpenSSH used to have a fixed internal window size that > made it slow on high bandwidth high latency links, and I notice the hpn USE > flag still exists in the openssh ebuild, which implies the issue with > openssh still exists. Rsync can use either ssh or its own protocol, so if > there's a high latency link between the two boxes and rsync is using ssh, > you could investigate rebuilding openssh with +hpn. > > What does ping show the latency as? > > Otherwise i'd be thinking about packet loss. First place to start for that > is on the endpoint interfaces; > ifconfig enp35s0f0 | grep err > RX errors 0 dropped 0 overruns 0 frame 0 > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 I'll test the above for errors tomorrow.
Re: [gentoo-user] network transfer speed
On 1/16/21 11:55 AM, Michael wrote: > On Friday, 15 January 2021 22:43:36 GMT the...@sys-concept.com wrote: > >> The fact that I'm logged via ssh over VPN to a remote network should not >> have any influence over network speed. > > It may influence speed if you're trying to push a large file through the > tunnel. TCP over TCP tends to choke due to retransmissions: > > http://sites.inka.de/bigred/devel/tcp-tcp.html > > Is the VPN you mention using a TCP or UDP tunnel? The VPN is using UDP tunnel. > >> I just made a loop: >> Network A ==> Internet ==> Network B >> ssh back to Network A over internet and run "rsync" I got same speed (as if >> I run the command locally) on Network A 112MB/s >> >> So the limiting factor is somewhere else. > > I'm sorry, but I fail to understand with any clarity what runs where and how > when you test things locally, Vs remotely. I mean: What I did is log-in to a remote network over ssh, from remote network I logged back to my network PC using ssh and tested the transfer speed. > - Network topology; > - Network Protocols; > - Applications & application protocols; > - Relevant services on each peer; > - Actions on each peer; > - Results per action. > > As already mentioned iperf or netcat/telnet results will confirm if this is > purely a network issue, ISPs performing deep packet inspection/throttling > affecting throughput asymmetrically, etc. > > SSDs are typically faster than spinning disks, but not always as fast as > ramdisks/tmpfs, especially if write amplification takes place, TRIM kicks in, > > etc. > > Stacking network + application protocols can also have an adverse effect. > Applications like rsync which compare file names, sizes, hashes and what not, > do not offer a reliable speed comparison. > > Methodically testing each component of the transmission system should get you > an answer at the end. On a remote network there are 5-pcs - two of them are Windows PC - 3-pcs are Gentoo I was just testing Getnoo PC's One small PC is about 20-30meters away from the switch and connected by CAT5 (or CAT5e) that PC is network card is capable of 1000-speed according to "ethtool" but negotiated the speed of 100 according to: /sys/class/net/enp4s0/speed The 2-PCs closer to the switch, negotiated the speed of 1000 according to: /sys/class/net/enp/speed I have to check (this week) if they are both connected directly to a switch and or firewall Ausus RT-AC66U and the light on the switch. I'll check out/investigate the use of "net-misc/iperf" to check the speed.
[gentoo-user] new installation - ERROR: dev-lang/rust-1.47.0-r2::gentoo failed (compile phase)
trace.
Traceback (most recent call last):
File "./x.py", line 11, in
bootstrap.main()
File
"/var/tmp/portage/dev-lang/rust-1.47.0-r2/work/rustc-1.47.0-src/src/bootstrap/bootstrap.py",
line 1009, in main
bootstrap(help_triggered)
File
"/var/tmp/portage/dev-lang/rust-1.47.0-r2/work/rustc-1.47.0-src/src/bootstrap/bootstrap.py",
line 995, in bootstrap
run(args, env=env, verbose=build.verbose)
File
"/var/tmp/portage/dev-lang/rust-1.47.0-r2/work/rustc-1.47.0-src/src/bootstrap/bootstrap.py",
line 143, in run
raise RuntimeError(err)
RuntimeError: failed to run:
/var/tmp/portage/dev-lang/rust-1.47.0-r2/work/rustc-1.47.0-src/build/bootstrap/debug/bootstrap
dist -vv
--config=/var/tmp/portage/dev-lang/rust-1.47.0-r2/work/rustc-1.47.0-src/config.toml
-j8
* ERROR: dev-lang/rust-1.47.0-r2::gentoo failed (compile phase):
* (no error message)
*
* Call stack:
* ebuild.sh, line 125: Called src_compile
* environment, line 3644: Called die
* The specific snippet of code:
* env $(cat "${S}"/config.env) RUST_BACKTRACE=1 "${EPYTHON}" ./x.py dist
-vv --config="${S}"/config.toml -j$(makeopts_jobs) || die )
--
Thelma
Re: [gentoo-user] fstab mount /home by default
On 1/17/21 1:22 AM, the...@sys-concept.com wrote: > On one of my system I have in fstab: > /dev/sda4 /home ext4noatime 0 1 > and /home is mounted by default > > On my new installation, I have in my fstab: > /dev/sda5 /home ext4noatime 0 1 > > but on new installation /home doesn't mount by default, why? > > On new installation, I created a user without "-m" > useradd -G users,wheel,audio -s /bin/bash thelma > > added to fstab: > /dev/sda5 /home ext4noatime 0 1 > > but it doesn't mount by default. > xfce4 created new entry in /home /thelma > so I deleted the entry /thelma but manual mounting: mount /dev/sda5 /home > does not create directory /thelma manually under /home > > When I mount manually /dev/sda5 /home all data is there but but trying login > as user "X" gets a black screen now. > How to get back "X" > > When I ssh and try to start it manually I get: > Fatal server error: > (EE) xf86OpenConsole: Cannot open virtual console 8 (Permission denied) Spelling :-/ It should be: dev/sda5/home ext4defaults 0 1
[gentoo-user] fstab mount /home by default
On one of my system I have in fstab: /dev/sda4 /home ext4noatime 0 1 and /home is mounted by default On my new installation, I have in my fstab: /dev/sda5 /home ext4noatime 0 1 but on new installation /home doesn't mount by default, why? On new installation, I created a user without "-m" useradd -G users,wheel,audio -s /bin/bash thelma added to fstab: /dev/sda5 /home ext4noatime 0 1 but it doesn't mount by default. xfce4 created new entry in /home /thelma so I deleted the entry /thelma but manual mounting: mount /dev/sda5 /home does not create directory /thelma manually under /home When I mount manually /dev/sda5 /home all data is there but but trying login as user "X" gets a black screen now. How to get back "X" When I ssh and try to start it manually I get: Fatal server error: (EE) xf86OpenConsole: Cannot open virtual console 8 (Permission denied)
Re: [gentoo-user] depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs unknown symbol
On 1/17/21 5:43 PM, the...@sys-concept.com wrote: > I'm compiling VirtualBox support into the latest kernel-5.4.80-gentoo-r1 > > [*] Virtualization ---> > <*> Kernel-based Virtual Machine (KVM) support > <*> KVM for AMD processors support > > And I get an error when compiling the kernel: make && make modules_install > > DEPMOD 5.4.80-gentoo-r1 > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_mmap > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_manager_func > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_device_release > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_kunmap > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_del_sub_from_lru > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_device_init > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_init_mm > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_dma_acc_size > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_tt_init > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_kmap > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_add_to_lru > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_init > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_validate > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_move_to_lru_tail > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_put > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_tt_fini > depmod: WARNING: /lib/modules/5.4.80-gentoo-r1/misc/vboxvideo.ko needs > unknown symbol ttm_bo_eviction_valuable In kernel-5.4.80-gentoo-r1 CONFIG_DRM_VBOXVIDEO is not set need to be set for VirtualBox. The strange part is that this setting is not enable in: kernel-5.4.72-gentoo x86_64 and VirtualBox is working and I never got any error messages like this when compiling kernel-5.4.72-gentoo
Re: [gentoo-user] network transfer speed
On 1/18/21 4:41 AM, bobwxc wrote: > 在 2021/1/18 下午6:19, J. Roeleveld 写道: >> On Monday, January 18, 2021 10:58:24 AM CET Raffaele BELARDI wrote: -Original Message- From: J. Roeleveld Sent: Monday, January 18, 2021 09:47 To: gentoo-user@lists.gentoo.org Subject: Re: [gentoo-user] network transfer speed Some cheaper switches fail-over to hub-mode when the traffic exceeds what it can manage. >>> Interesting, do you have pointers to such switches' specs? Or is it from >>> experience? > That's true. > Some cheap switches may become like a network cable when it fails or exceeds > network flow. And there is also no log to check, will cause some strange > problems. > > Actually , some business machines also have such a policy that they become > straight through or completely blocked in case of failure. But they have a > fail log for review. >> This is from experience, also 1 of the reasons why I switched to managed >> switches. >> >> -- >> Joost What switch would you folks recommend? I'm planning getting to the bottom of it including replacing switch and cable if I have to.
[gentoo-user] Failed to load vboxpci
emerge --info Portage 3.0.13 (python 3.8.6-final-0, default/linux/amd64/17.1/desktop, gcc-9.3.0, glibc-2.32-r5, 5.4.80-gentoo-r1 x86_64) This is new installation. cat /etc/modules-load.d/virtualbox.conf vboxdrv vboxnetadp vboxnetflt vboxpci All modules are loading OK except "vboxpci" modprobe vboxpci modprobe: FATAL: Module vboxpci not found in directory /lib/modules/5.4.80-gentoo-r1
Re: [gentoo-user] Failed to load vboxpci
On 1/18/21 2:12 PM, tastytea wrote: > On 2021-01-18 14:04-0700 the...@sys-concept.com wrote: > >> emerge --info >> Portage 3.0.13 (python 3.8.6-final-0, >> default/linux/amd64/17.1/desktop, gcc-9.3.0, glibc-2.32-r5, >> 5.4.80-gentoo-r1 x86_64) >> >> This is new installation. >> cat /etc/modules-load.d/virtualbox.conf >> vboxdrv >> vboxnetadp >> vboxnetflt >> vboxpci >> >> All modules are loading OK except "vboxpci" >> >> modprobe vboxpci >> modprobe: FATAL: Module vboxpci not found in directory >> /lib/modules/5.4.80-gentoo-r1 > > app-emulation/virtualbox-modules does not install vboxpci.ko here. I > guess the information in the wiki is outdated. > > $ equery files app-emulation/virtualbox-modules | grep '\.ko$' > /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxdrv.ko > /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetadp.ko > /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetflt.ko > > Kind regards, tastytea I have the same output: # equery files app-emulation/virtualbox-modules | grep '\.ko$' /lib/modules/5.4.80-gentoo-r1/misc/vboxdrv.ko /lib/modules/5.4.80-gentoo-r1/misc/vboxnetadp.ko /lib/modules/5.4.80-gentoo-r1/misc/vboxnetflt.ko What is missing is in 5.4.80-gentoo-r1 is: vboxpci.ko In my old kernel it was there: /lib/modules/5.4.72-gentoo/misc/vboxpci.ko
Re: [gentoo-user] Failed to load vboxpci
On 1/18/21 2:31 PM, the...@sys-concept.com wrote: > On 1/18/21 2:12 PM, tastytea wrote: >> On 2021-01-18 14:04-0700 the...@sys-concept.com wrote: >> >>> emerge --info >>> Portage 3.0.13 (python 3.8.6-final-0, >>> default/linux/amd64/17.1/desktop, gcc-9.3.0, glibc-2.32-r5, >>> 5.4.80-gentoo-r1 x86_64) >>> >>> This is new installation. >>> cat /etc/modules-load.d/virtualbox.conf >>> vboxdrv >>> vboxnetadp >>> vboxnetflt >>> vboxpci >>> >>> All modules are loading OK except "vboxpci" >>> >>> modprobe vboxpci >>> modprobe: FATAL: Module vboxpci not found in directory >>> /lib/modules/5.4.80-gentoo-r1 >> >> app-emulation/virtualbox-modules does not install vboxpci.ko here. I >> guess the information in the wiki is outdated. >> >> $ equery files app-emulation/virtualbox-modules | grep '\.ko$' >> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxdrv.ko >> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetadp.ko >> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetflt.ko >> >> Kind regards, tastytea > > I have the same output: > > # equery files app-emulation/virtualbox-modules | grep '\.ko$' > /lib/modules/5.4.80-gentoo-r1/misc/vboxdrv.ko > /lib/modules/5.4.80-gentoo-r1/misc/vboxnetadp.ko > /lib/modules/5.4.80-gentoo-r1/misc/vboxnetflt.ko > > What is missing is in 5.4.80-gentoo-r1 is: vboxpci.ko > > In my old kernel it was there: > /lib/modules/5.4.72-gentoo/misc/vboxpci.ko It seems to me this driver is no longer needed/used.
[gentoo-user] BIOS can not find boot partition
I'm missing something as system can not find boot device fdisk /dev/nvme0n1 Disklabel type: gpt Device StartEndSectors Size Type /dev/nvme0n1p1 2048 6143 4096 2M BIOS boot /dev/nvme0n1p2 6144 268287 262144 128M EFI System /dev/nvme0n1p326828813168631048576 512M Linux swap /dev/nvme0n1p4 1316864 315889663 314572800 150G Linux filesystem I don't want to use EFI. /boot = dev/nvme0n1p2 (ext4) file system When I run: grub-install /dev/nvme0n1p2 Installing for x86_64-efi platform. grub-install: error: cannot find EFI directory. but there is /boot/grub Running: grub-mkconfig -o /boot/grub/grub.cfg is OK (no errors) fstab: /dev/nvme0n1p2 /boot ext4noauto,noatime 1 2 The BIOS has CSM compatibly mode enable. When I try to boot, system can not find bootable partition. Am I suppose to put any file system on /dev/nvme0n1p1 (2Mb partition) the installation manual did not mention anything.
Re: [gentoo-user] Failed to load vboxpci
On 1/18/21 2:46 PM, Neil Bothwick wrote: > On Mon, 18 Jan 2021 14:31:49 -0700, the...@sys-concept.com wrote: > >> On 1/18/21 2:12 PM, tastytea wrote: >>> On 2021-01-18 14:04-0700 the...@sys-concept.com wrote: >>> emerge --info Portage 3.0.13 (python 3.8.6-final-0, default/linux/amd64/17.1/desktop, gcc-9.3.0, glibc-2.32-r5, 5.4.80-gentoo-r1 x86_64) This is new installation. cat /etc/modules-load.d/virtualbox.conf vboxdrv vboxnetadp vboxnetflt vboxpci All modules are loading OK except "vboxpci" modprobe vboxpci modprobe: FATAL: Module vboxpci not found in directory /lib/modules/5.4.80-gentoo-r1 >>> >>> app-emulation/virtualbox-modules does not install vboxpci.ko here. I >>> guess the information in the wiki is outdated. >>> >>> $ equery files app-emulation/virtualbox-modules | grep '\.ko$' >>> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxdrv.ko >>> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetadp.ko >>> /lib/modules/5.4.80-gentoo-r1-x86_64/misc/vboxnetflt.ko >>> >>> Kind regards, tastytea >> >> I have the same output: >> >> # equery files app-emulation/virtualbox-modules | grep '\.ko$' >> /lib/modules/5.4.80-gentoo-r1/misc/vboxdrv.ko >> /lib/modules/5.4.80-gentoo-r1/misc/vboxnetadp.ko >> /lib/modules/5.4.80-gentoo-r1/misc/vboxnetflt.ko >> >> What is missing is in 5.4.80-gentoo-r1 is: vboxpci.ko >> >> In my old kernel it was there: >> /lib/modules/5.4.72-gentoo/misc/vboxpci.ko > > Your old kernel could have it from an older installation of > virtualbox-modules, that module is no longer installed > > % qlist virtualbox-modules > /lib/modules/5.4.80-gentoo-r1/misc/vboxnetflt.ko > /lib/modules/5.4.80-gentoo-r1/misc/vboxnetadp.ko > /lib/modules/5.4.80-gentoo-r1/misc/vboxdrv.ko > /etc/modprobe.d/vboxdrv.conf > /usr/lib/modules-load.d/virtualbox.conf > > And the virtualbox.conf file contains > > vboxdrv > vboxnetflt > vboxnetadp > > No mention of vboxpci. > > Does VirtualBox work? Yes, it works. Gentoo wiki did not get updated, in addition I was copying configuration from previous kernel that I just installed a month ago or so. It is hard o catch all the changes during updates.
Re: [gentoo-user] new installation - ERROR: dev-lang/rust-1.47.0-r2::gentoo failed (compile phase)
On 1/17/21 4:18 AM, Michael wrote: > On Sunday, 17 January 2021 11:04:17 GMT Peter Humphrey wrote: >> On Saturday, 16 January 2021 20:59:17 GMT the...@sys-concept.com wrote: >>> Reinstalling Gentoo on one box (I wiped the root partition, so it is a >>> clean install) and I'm getting this error >> >> --->8 >> >> Have you thought of using rust-bin instead of rust? "emerge -1 rust-bin" It >> saves prodigious amounts of compiling here. Of course, you can't do that if >> you need to set particular USE flags. >> >> There was a discussion here a month or two ago. Either rust or rust-bin will >> satisfy virtual/rust. > > > Rust uses up tonnes of RAM in compiling, so unless enough RAM and perhaps > SWAP > is available, it could fail. Increasing resources and/or reducing the make > job number should improve the situation. I think that might have been the case, I run emerge second time and it compiled just fine. Maybe I will switch to "rust-bin", thanks for suggestion. Why do we need it, is it part of "system-bootstrap"?
[gentoo-user] network transfer speed
On both of my systems the network card speed is showing 1000 cat /sys/class/net/enp4s0/speed 1000 but when I do rsync larage file I only see about: 20 to 22MB/s On my home network I get about 110MB/s between PC's Both PC's have SSD and the swith is Gigabit (I think). How to find a the bottleneck?
Re: [gentoo-user] network transfer speed
On 1/15/21 6:26 AM, Hogren wrote: > > On 15/01/2021 09:34, Raffaele BELARDI wrote: >> >> ST Restricted >> >>> -Original Message- >>> From: Hogren >>> Sent: Friday, January 15, 2021 08:50 >>> To: gentoo-user@lists.gentoo.org >>> Subject: Re: [gentoo-user] network transfer speed >>> >>> >>> On 15/01/2021 07:56, the...@sys-concept.com wrote: >>> Hello On both of my systems the network card speed is showing 1000 cat /sys/class/net/enp4s0/speed 1000 but when I do rsync larage file I only see about: 20 to 22MB/s On my home network I get about 110MB/s between PC's Both PC's have SSD and the swith is Gigabit (I think). How to find a the bottleneck? >>> 20MB = 80Mb so it sounds like your network is a 100Mb network. What is the >>> perfs of your switch(s) between your systems ? >> I disagree, /sys/class/net/enp4s0/speed shows the speed negotiated by the >> network card with the switch, it cannot be 1000 if the switch is a only a >> 10/100. I think we can safely assume the network is a gigabit one. >> >> raffaele > > Yes, I thought about that after. But may be he has several switchs between > the two systems. > > Hogren I just checked the remote location and there are two swiches: - D-link Green Technology (I think it is DSG-1005D - Trident Gigabit Switch - TEG-S80g They are both Gigabit switches.
Re: [gentoo-user] network transfer speed
On 1/15/21 2:58 AM, Michael wrote: > On Friday, 15 January 2021 08:42:16 GMT bobwxc wrote: >> 在 2021/1/15 下午4:27, Raffaele BELARDI 写道: -Original Message- From: bobwxc Sent: Friday, January 15, 2021 08:57 To: gentoo-user@lists.gentoo.org Subject: Re: [gentoo-user] network transfer speed 在 2021/1/15 下午2:56, the...@sys-concept.com 写道: > On both of my systems the network card speed is showing 1000 > cat /sys/class/net/enp4s0/speed 1000 > > but when I do rsync larage file I only see about: 20 to 22MB/s On my > home network I get about 110MB/s between PC's > > Both PC's have SSD and the swith is Gigabit (I think). > How to find a the bottleneck? 1000Mbps network card's maximum theoretical speed is about 125MiB/s. It only works in short distances. >>> >>> Correct but that's the line speed that you'll never reach, when you take >>> into account Ethernet frame overhead, IP (and possibly TCP) header >>> overhead and application ( rsync, FTP, SMB, NFS) overhead you get lower >>> figures. In my experience 900Mbps (110MiBps) on a 1000Mbps line is more >>> realistic for 'normal' transfers. >> Yes, you are right. So it is just *theoretical* speed :-) >> >> I don't know where does the file he sync from. >> If you sync a file from a server in other city, for a 20 to 22MB/s speed >> is very normal. But if in home, that is not good. >> >> And for ftp and rsync. >> ftp is better for transferring a single large file once. >> rsync is better for a long-term, incremental synchronization. The >> file verification of rsync may take a lot of time for first sync. > > There is a theoretical network speed as already mentioned. There is a > protocol speed, which may limit throughput if it has e.g. heavy encryption/ > compression and the CPU is anaemic. Finally, there is a MoBo bus (SCSI/SATA/ > USB) and the media storage limit. If using USB 1.1 or 2.0 and/or the disks > are slow or experience write amplification, you'll find this will constrain > the final transfer speed significantly. The computers on this network are 2-meters apart and they both use SSD Drive (so USB limitation doesn't come under consideration). Like I said, on my home network when I transfer the 24GB file I get about 110MiBps transfer, so I was expecting the same in remote location). Some units are connected to a router Ausus RT-AC66U B1 but these ports are gigabit too.
Re: [gentoo-user] network transfer speed
On 1/15/21 9:55 AM, Jack wrote: > On 1/15/21 11:51 AM, the...@sys-concept.com wrote: >> On 1/15/21 2:58 AM, Michael wrote: >>> On Friday, 15 January 2021 08:42:16 GMT bobwxc wrote: 在 2021/1/15 下午4:27, Raffaele BELARDI 写道: >> -Original Message- >> From: bobwxc >> Sent: Friday, January 15, 2021 08:57 >> To: gentoo-user@lists.gentoo.org >> Subject: Re: [gentoo-user] network transfer speed >> >> 在 2021/1/15 下午2:56, the...@sys-concept.com 写道: >>> On both of my systems the network card speed is showing 1000 >>> cat /sys/class/net/enp4s0/speed 1000 >>> >>> but when I do rsync larage file I only see about: 20 to 22MB/s On my >>> home network I get about 110MB/s between PC's >>> >>> Both PC's have SSD and the swith is Gigabit (I think). >>> How to find a the bottleneck? >> 1000Mbps network card's maximum theoretical speed is about 125MiB/s. >> It only works in short distances. > Correct but that's the line speed that you'll never reach, when you take > into account Ethernet frame overhead, IP (and possibly TCP) header > overhead and application ( rsync, FTP, SMB, NFS) overhead you get lower > figures. In my experience 900Mbps (110MiBps) on a 1000Mbps line is more > realistic for 'normal' transfers. Yes, you are right. So it is just *theoretical* speed :-) I don't know where does the file he sync from. If you sync a file from a server in other city, for a 20 to 22MB/s speed is very normal. But if in home, that is not good. And for ftp and rsync. ftp is better for transferring a single large file once. rsync is better for a long-term, incremental synchronization. The file verification of rsync may take a lot of time for first sync. >>> There is a theoretical network speed as already mentioned. There is a >>> protocol speed, which may limit throughput if it has e.g. heavy encryption/ >>> compression and the CPU is anaemic. Finally, there is a MoBo bus >>> (SCSI/SATA/ >>> USB) and the media storage limit. If using USB 1.1 or 2.0 and/or the disks >>> are slow or experience write amplification, you'll find this will constrain >>> the final transfer speed significantly. >> The computers on this network are 2-meters apart and they both use SSD Drive >> (so USB limitation doesn't come under consideration). >> Like I said, on my home network when I transfer the 24GB file I get about >> 110MiBps transfer, so I was expecting the same in remote location). >> Some units are connected to a router Ausus RT-AC66U B1 but these ports are >> gigabit too. > When you say the computers are remote, is it possible the file is passing > through your local computer on the way between the two remote machines? > Where are you actually running the rsync command? I ssh over VPN to remote computers and run "rsync" there. Will it effect the speed?
[gentoo-user] merged on \${HOST} with notice"
I have in a new machine (as on all other boxes) in make.conf
PORTAGE_ELOG_MAILSUBJECT="package \${PACKAGE} merged on \${HOST} with notice"
In /etc/conf.d/hostname
hostname="syscon3"
But when a package is emerge I receive via email notice as in subject line:
"...merged on localhost.localdomain"
eg: package dev-vcs/git-2.26.2 merged on localhost.localdomain with notice
Which file define "${HOST}"
[gentoo-user] Apache - prevent local ip from log files
Trying to prevent local local IP from appearing in log files.
I have in modules.d/00_mod_log_config.conf
DeflateFilterNote Input instream
DeflateFilterNote Output outstream
DeflateFilterNote Ratio ratio
LogFormat '"%h %l %u %t \"%r\" %{outstream}n/%{instream}n (%{ratio}n%%)' deflate
SetEnvIf Remote_Addr "127\.0\.0\.1" dontlog
SetEnvIf Remote_Addr "10\.0\.0\.109" dontlog
CustomLog /var/log/apache2/access_log common env=!dontlog
This setting worked in Apache 2.2 but Apache 2.4 is still logging all my
localhost IP's.
Re: [gentoo-user] thunderbird - 78.6.0 disable line wrap
On 1/2/21 2:55 AM, Remco Rijnders wrote: > On Fri, Jan 01, 2021 at 09:40:59PM -0700, thelma wrote in > <4047b613-de75-3eeb-46cf-df4895577...@sys-concept.com>: >> I was using old version of thunderbird and line wrap was in "Option" menu; >> but in new version "line wrap On/Off" disappeared. >> >> How to disable line wrap? > > They make this really impossible to find... Anyways, go to the menu Edit --> > Preferences, then scroll down go to the bottom option in the window that shows > "Config Editor...". Click to accept the risk and void your warranty. In the > search bar, enter "wrap". I think the settings you'll want are > mail.wrap_long_lines and/or plain_text.wrap_long_lines. Double click to change > the values. The changed settings should take effect immediately. > > I hope this helps. > > Kind regards, > > Remco Yes, I found it. They keep changing these settings; I don't know why. Changing: "mailnews.wraplength" value "72" to "0" Solved the problem thanks
[gentoo-user] Apache 2.4 - set SecStatusEngine to On
Status engine is currently disabled, enable it by set SecStatusEngine to On. How to enable "SecStatusEngine to On" in Apache 2.4 From my log file: [Fri Jan 01 19:44:52.649498 2021] [core:notice] [pid 14152] AH00094: Command line: '/usr/sbin/apache2 -D DEFAULT_VHOST -D INFO -D SSL -D SSL_DEFAULT_VHOST -D LANGUAGE -D PHP -D SECURITY -d /usr/lib64/apache2 -f /etc/apache2/httpd.conf' [Fri Jan 01 21:10:26.781254 2021] [mpm_prefork:notice] [pid 14152] AH00169: caught SIGTERM, shutting down [Fri Jan 01 21:10:27.871561 2021] [:notice] [pid 16586] ModSecurity for Apache/2.9.3 (http://www.modsecurity.org/) configured. [Fri Jan 01 21:10:27.871577 2021] [:notice] [pid 16586] ModSecurity: APR compiled version="1.7.0"; loaded version="1.7.0" [Fri Jan 01 21:10:27.871579 2021] [:notice] [pid 16586] ModSecurity: PCRE compiled version="8.44 "; loaded version="8.44 2020-02-12" [Fri Jan 01 21:10:27.871581 2021] [:notice] [pid 16586] ModSecurity: LIBXML compiled version="2.9.10" [Fri Jan 01 21:10:27.871582 2021] [:notice] [pid 16586] ModSecurity: Status engine is currently disabled, enable it by set SecStatusEngine to On.
[gentoo-user] thunderbird - 78.6.0 disable line wrap
I was using old version of thunderbird and line wrap was in "Option" menu; but in new version "line wrap On/Off" disappeared. How to disable line wrap?
[gentoo-user] sound not working
I have: lspci | grep -i audio 08:00.1 Audio device: NVIDIA Corporation GP107GL High Definition Audio Controller (rev a1) 0a:00.4 Audio device: Advanced Micro Devices, Inc. [AMD] Starship/Matisse HD Audio Controller Kernel (seems like correct driver) grep -i snd_hda_intel .config CONFIG_SND_HDA_INTEL=y # CONFIG_SND_HDA_INTEL_DETECT_DMIC is not set User is in "audio" group. alsamixer is showing only: Card: PulseAudio Chip: PulseAudio Shouldn't it be showing some kind of Nvidia audio?
[gentoo-user] Thunderbird - Unable to save your message as a draft.
With Thunderbird-78.6.0 I'm getting an error message when composing messages: Unable to save your message as a draft. Sending of the message failed. What is the solution? I've run onto few of them but they are mostly for Windows users not really applicable to Linux.
Re: [gentoo-user] preventing some IP's from from being logged in apache
On 1/11/21 11:32 PM, J. Roeleveld wrote: [snip] > If you blocked the IP in the firewall, it shouldn't show in the log. > > Add iptables to the webserver and block that IP. > Personally, I would block the whole range (45.93.201.0/24), which is either > linked to Cyprus or Russia (according to whois) > > Any block in the apache-config might fail due to a bug or new configuration. > > -- > Joost Asus routers don't have capabilities to block external IP's (I need to find a better router). Blocking that IP range in apache works, all the IPs I blocked are getting 403 error (regardless what they type) but you might be right, apache 2.4 SetEnvIf Remote_Addr "45\.93\.201\.104" dontlog (does not work). I wish they design blocking by country easier.
Re: [gentoo-user] sound not working
On 1/2/21 10:45 PM, the...@sys-concept.com wrote: > I have: > lspci | grep -i audio > 08:00.1 Audio device: NVIDIA Corporation GP107GL High Definition Audio > Controller (rev a1) > 0a:00.4 Audio device: Advanced Micro Devices, Inc. [AMD] Starship/Matisse HD > Audio Controller > > Kernel (seems like correct driver) > grep -i snd_hda_intel .config > CONFIG_SND_HDA_INTEL=y > # CONFIG_SND_HDA_INTEL_DETECT_DMIC is not set > > User is in "audio" group. > alsamixer is showing only: > Card: PulseAudio > Chip: PulseAudio > > Shouldn't it be showing some kind of Nvidia audio? I was able to make it to work by compiling some additional codec in kernel but I can not store the alsa letting: alsamixer XDG_RUNTIME_DIR (/run/user/1000) is not owned by us (uid 0), but by uid 1000! (This could e.g. happen if you try to connect to a non-root PulseAudio as a root user, over the native protocol. Don't do that.) What to do with it?
Re: [gentoo-user] ssh Connection reset by port 22
On 12/15/2020 11:35 PM, the...@sys-concept.com wrote: [snip] > > tail -f /var/log/auth.log (on the server) > does not show any log-in attempt > > only: > sshd: Server listening on 0.0.0.0 port 22 > sshd: Server listening on :: port 22 Solved by reinstalling openssh.
Re: [gentoo-user] [SOLVED] fsck.fat 4.1 - File system couldn't be fixed [SOLVED]
On 12/13/2020 06:33 AM, Victor Ivanov wrote: [snip] > > Out of curiosity, do you have the "sys-fs/dosfstools" package installed? > > This is the package that provides the fsck.fat binary. It's not a > dependency of commonly installed system packages so unless you install > it manually it's probably missing which might explain why fsck is > exiting with an error code. > > - Victor Yes, I had this packaged installed, but it did not help. I got hit by this bug. I'm surprised that it hasn't been discovered earlier.
[gentoo-user] fsck.fat 4.1 - File system couldn't be fixed
I wipe the /boot, reinstall kernel, initframes, grub. The system boots, I can login as root but X is not running, the command is displaying: "(none) /#" When I try to start the network I get: fsck.fat 4.1 (2017-01-24) open: no such file or directory Filesystems couldn't be fixed ERROR: fsck failed to start It seems to me "/" file system mount in "read only" mode. When I try to emerge anything I get: /var/log/emerge.log Read-only file system.
[gentoo-user] spam - different IP's
I'm perplex with this entry in apache log. I'm sure it was done by same person as the timing is very sequential and same file-name request, but how they were able to lunch an attack from a different IP's different geographical locations. Can they spoof an IP? 173.201.196.206 - - [03/Feb/2021:19:17:47 -0700] "GET /wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 195.70.43.234 - - [03/Feb/2021:19:18:24 -0700] "GET /wordpress/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 198.38.92.110 - - [03/Feb/2021:19:21:18 -0700] "GET /new/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 50.62.208.141 - - [03/Feb/2021:19:21:20 -0700] "GET /en/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 64.62.206.242 - - [03/Feb/2021:19:21:34 -0700] "GET /web/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 184.168.46.171 - - [03/Feb/2021:19:22:11 -0700] "GET /home/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 50.63.196.23 - - [03/Feb/2021:19:23:41 -0700] "GET /www/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 203.205.21.159 - - [03/Feb/2021:19:23:57 -0700] "GET /staging/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 66.113.226.191 - - [03/Feb/2021:19:25:42 -0700] "GET /news/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 148.72.232.107 - - [03/Feb/2021:19:26:06 -0700] "GET /news/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 35.208.134.190 - - [03/Feb/2021:19:26:22 -0700] "GET /shop/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 160.153.153.30 - - [03/Feb/2021:19:26:50 -0700] "GET /main/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 192.241.230.24 - - [03/Feb/2021:19:27:50 -0700] "GET /v2/wp-includes/wlwmanifest.xml HTTP/1.1" 403 199 66.113.221.43 - - [03/Feb/2021:19:28:37 -0700] "GET /website/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 2.50.180.72 - - [03/Feb/2021:19:28:48 -0700] "GET /portal/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 104.236.82.97 - - [03/Feb/2021:19:29:39 -0700] "GET /2019/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 50.63.197.91 - - [03/Feb/2021:19:30:46 -0700] "GET /1/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 103.27.61.222 - - [03/Feb/2021:19:30:57 -0700] "GET /store/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 184.168.152.18 - - [03/Feb/2021:19:31:14 -0700] "GET /wp2/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 184.168.193.129 - - [03/Feb/2021:19:31:24 -0700] "GET /blogs/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196
Re: [gentoo-user] spam - different IP's
On 2/3/21 10:22 PM, the...@sys-concept.com wrote: > I'm perplex with this entry in apache log. > I'm sure it was done by same person as the timing is very sequential and same > file-name request, but how they were able to lunch an attack from a different > IP's different geographical locations. > Can they spoof an IP? > > 173.201.196.206 - - [03/Feb/2021:19:17:47 -0700] "GET > /wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 195.70.43.234 - - [03/Feb/2021:19:18:24 -0700] "GET > /wordpress/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 198.38.92.110 - - [03/Feb/2021:19:21:18 -0700] "GET > /new/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 50.62.208.141 - - [03/Feb/2021:19:21:20 -0700] "GET > /en/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 64.62.206.242 - - [03/Feb/2021:19:21:34 -0700] "GET > /web/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 184.168.46.171 - - [03/Feb/2021:19:22:11 -0700] "GET > /home/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 50.63.196.23 - - [03/Feb/2021:19:23:41 -0700] "GET > /www/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 203.205.21.159 - - [03/Feb/2021:19:23:57 -0700] "GET > /staging/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 66.113.226.191 - - [03/Feb/2021:19:25:42 -0700] "GET > /news/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 148.72.232.107 - - [03/Feb/2021:19:26:06 -0700] "GET > /news/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 35.208.134.190 - - [03/Feb/2021:19:26:22 -0700] "GET > /shop/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 160.153.153.30 - - [03/Feb/2021:19:26:50 -0700] "GET > /main/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 192.241.230.24 - - [03/Feb/2021:19:27:50 -0700] "GET > /v2/wp-includes/wlwmanifest.xml HTTP/1.1" 403 199 > 66.113.221.43 - - [03/Feb/2021:19:28:37 -0700] "GET > /website/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 2.50.180.72 - - [03/Feb/2021:19:28:48 -0700] "GET > /portal/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 104.236.82.97 - - [03/Feb/2021:19:29:39 -0700] "GET > /2019/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 50.63.197.91 - - [03/Feb/2021:19:30:46 -0700] "GET > /1/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 103.27.61.222 - - [03/Feb/2021:19:30:57 -0700] "GET > /store/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 184.168.152.18 - - [03/Feb/2021:19:31:14 -0700] "GET > /wp2/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 > 184.168.193.129 - - [03/Feb/2021:19:31:24 -0700] "GET > /blogs/wp-includes/wlwmanifest.xml HTTP/1.1" 404 196 Correction: should be "launch"
Re: [gentoo-user] lightdm - can not login
On 6/11/21 2:17 AM, Michael wrote: > On Thursday, 10 June 2021 22:42:10 BST the...@sys-concept.com wrote: >> On 6/10/21 2:38 PM, Michael wrote: >>> On Thursday, 10 June 2021 21:22:12 BST the...@sys-concept.com wrote: On 6/10/21 1:19 PM, the...@sys-concept.com wrote: > I'm trying to use the default "lightdm" for login but whenever I type-in > the password it it puts me back to login screen (asking for password) I > changed/updated the password and the system accept it but I still can > not > log-in. I switched to "sddm" and it works, but it is "ugly". >>> >>> There are some themes you could choose from, or make your own to improve >>> the aesthetics of its default appearance. Access to themes may be >>> available via your desktop environment's settings, or by setting them >>> manually in sddm.conf.> How to enable "num-lock" with sddm? I have "num-lock" in default run-level and it turns on when system is booting but when the "sddm" starts the num-lock is OFF again. >>> >>> The default /usr/share/sddm/sddm.conf.d/00default.conf has: >>> >>> # Initial NumLock state. Can be on, off or none. >>> # If property is set to none, numlock won't be changed >>> # NOTE: Currently ignored if autologin is enabled. >>> Numlock=none >>> >>> You can change this in yours to 'on' and see if it makes any difference. >> >> In: /usr/share/sddm/sddm.conf.d/00default.conf >> I change to >> Numlock=on >> >> It makes no difference, when system boots the "Numlock" is still off. > > By "... when system boots" you mean when sddm starts, or when the xfce4 > desktop loads? > > Is it actually off, or is the corresponding LED failing to illuminate, but > the > keyboard responds correctly? > > https://forum.xfce.org/viewtopic.php?id=3270 > > > I do not have numlock enabled via openrc on the default runlevel and I have > not installed numlockx. I copied the numlock configuration snippet into /etc/ > sddm.conf and set it to 'on'. Restarting enabled the numlock function and > turned on the LED too, once sddm was running. After login into a desktop > finished (Plasma) the numlock remained on. So on this machine it works as > advertised with sddm and a Plasma DE. > > xfce4 has a desktop setting, under Settings > Keyboard where you can enable > numlock - without depending on the display manager. > > >> There >> is no default user login either and some kind of "Consoll log for..." on >> the lower right hand corner (that user don't need to see). > > This is not what I see here of a number of different PCs. There are avatars > for each linux user and there is no log showing on the sddm panel. Do you > have missing components like e.g. elogind, policykit? > > If the OS have only one user then this user's avatar will be selected to > login > with. With more than one user, the last user who logged in will be selected. > > >> Previously I did not use any log-in manager, I start X from >> .bash_profile >> if [[ -z $DISPLAY ]] && [[ $(tty) = /dev/tty1 ]]; then exec startx; fi >> >> .xinitrc >> exec startxfce4 > > Have you looked at this page - it describes bashrc as an option: > > https://wiki.gentoo.org/wiki/X_without_Display_Manager > > >> but I'm not sure if it runs/starts in VT=7 >> How to check or force X to VT=7 > > Ctrl+Alt+Fn to discover which virtual terminal your Xsession is running on. I'm back on "LightDM" login manager, the login works. It was as simple as selecting, in top right hand corner (on "setting") during Login "Xfce" instead of "Xsession" that is using "twm" which I don't have it even installed. Xfce4 is the only desktop I have so it should be a default one. As for numlock it still not ON. The solution I think is to install: "x11-misc/numlockx" and point to it the configuration file. I but I have "numlock" in default run-level and during start up the Numlock key turn ON but as soon as the "LightDM" starts, the Numlock light goes OFF. Installing another application just to turn it ON is pointless.
Re: [gentoo-user] MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to open display ":0"
On 6/11/21 7:12 PM, the...@sys-concept.com wrote: > After installing and logging via LightDM > When I try to login over X2GO I get: > > Connection failed. Invalid MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to > open display ":0" Invalid MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to > open display ":0" The reason, why I'm getting this error is that "LightDM" as automatic logout. Anybody know how to prevent it?
[gentoo-user] MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to open display ":0"
After installing and logging via LightDM When I try to login over X2GO I get: Connection failed. Invalid MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to open display ":0" Invalid MIT-MAGIC-COOKIE-1 keyxwininfo: error: unable to open display ":0"
