On Sun, Dec 21, 2014 at 10:14:46PM +0100, Wolfram Sang wrote:
This platform_driver does not need to set an owner, it will be populated by
the
driver core.
Applied, thanks.
signature.asc
Description: Digital signature
Hi Roger,
On Friday 19 December 2014 05:35 PM, Roger Quadros wrote:
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.
Due to Errata i783 SATA Lockup After SATA DPLL Unlock/Relock
we can't allow SATA DPLL to be
Hi Vivek,
On 25/11/14 12:48, Vivek Gautam wrote:
On Sat, Nov 22, 2014 at 8:42 PM, Kukjin Kim kg...@kernel.org wrote:
On 11/22/14 17:40, Kishon Vijay Abraham I wrote:
On Friday 21 November 2014 08:41 PM, Felipe Balbi wrote:
...
I took dwc3 driver patches.
I took the phy patches.
On 20 December 2014 at 00:07, NeilBrown ne...@suse.de wrote:
One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.
To make it possible for omap_hsmmc (and maybe others) to be converted
to
On Tue, Dec 16, 2014 at 10:10:28AM +0800, Sneeker Yeh wrote:
Synopsis DesignWare USB3 IP Core integrated with a config-free
phy needs special handling during device disconnection to avoid
the host controller dying.
This quirk makes sure PORT_CSC is cleared after the disable slot
command
Hi,
On Tue, Dec 16, 2014 at 10:10:27AM +0800, Sneeker Yeh wrote:
This patch adds support for Synopsis DesignWare USB3 IP Core found
on Fujitsu Socs.
Signed-off-by: Sneeker Yeh sneeker@tw.fujitsu.com
---
.../devicetree/bindings/usb/fujitsu-dwc3.txt | 25 +++
On Fri, Dec 19, 2014 at 12:40:15PM +0530, Amit Virdi wrote:
When scatter gather is used, multiple TRBs are prepared from one DWC3 request.
Hence, we must set the 'last' flag when the SG is last as well as the TRB is
last. The current implementation uses list_is_last to check if the
On Fri, Dec 19, 2014 at 12:40:16PM +0530, Amit Virdi wrote:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The driver must stop preparing TRBs when the max TRBs have been prepared. The
code was missing break
The omap1's debug-macro.S is similar to the generic 8250 code. Compared to
the 8520 code the omap1 macro automatically determines what UART to use
based on breadcrumbs left by the bootloader and automatically copes with
the eccentric register layout on OMAP7XX.
This patch drops both these
On Thu, Dec 11, 2014 at 11:42:48AM +0100, Marek Szyprowski wrote:
On 2014-12-11 10:29, Russell King - ARM Linux wrote:
On Wed, Dec 10, 2014 at 10:42:33AM +0100, Marek Szyprowski wrote:
I assume that now it won't be possible to get l2c patches back to -next,
so I will resend them (again...)
* Russell King - ARM Linux li...@arm.linux.org.uk [141222 09:06]:
On Thu, Dec 11, 2014 at 11:42:48AM +0100, Marek Szyprowski wrote:
On 2014-12-11 10:29, Russell King - ARM Linux wrote:
On Wed, Dec 10, 2014 at 10:42:33AM +0100, Marek Szyprowski wrote:
I assume that now it won't be possible
On Mon, Dec 22, 2014 at 11:04 AM, Russell King - ARM Linux
li...@arm.linux.org.uk wrote:
Nishanth - can we push OMAP over to using the generic DT L2C
initialisation (the one from init_IRQ in arch/arm/kernel/irq.c) and
kill the SoC specific stuff in arch/arm/mach-omap2/omap4-common.c ?
From
On Mon, Dec 22, 2014 at 11:12:42AM -0600, Nishanth Menon wrote:
On Mon, Dec 22, 2014 at 11:04 AM, Russell King - ARM Linux
li...@arm.linux.org.uk wrote:
That only leaves the non-DT stuff to worry about this, and from what I
understand, that's going to be removed soon. If we're going to keep
By converting a few drivers to modules because they
won't be needed during boot anyways, we can shave off
about 700KiB of text.
Note that while at that, and after discussions with Tony
Lindgren, a few extra drivers were either removed because
they weren't needed, or added because they're useful
On Mon, Dec 22, 2014 at 12:05:35PM -0600, Felipe Balbi wrote:
By converting a few drivers to modules because they
won't be needed during boot anyways, we can shave off
about 700KiB of text.
Note that while at that, and after discussions with Tony
Lindgren, a few extra drivers were either
On Thu, Dec 04, 2014 at 09:24:39AM -0600, Felipe Balbi wrote:
From: Dave Gerlach d-gerl...@ti.com
Hook dcdc2 as the cpu0-supply.
Signed-off-by: Dave Gerlach d-gerl...@ti.com
Signed-off-by: Felipe Balbi ba...@ti.com
btw, before sending this, I tested on my AM437x Starter Kit, so
The AM437x Industrial Development Kit (IDK) is
an application development platform targeted at
industrial communication and control applications.
It comes with a 3-phase motor driver, PROFINET,
PROFIBUS and a few other industrial communication
interfaces.
The board has 1GiB of DDR3 RAM, QSPI NOR
Hi Felipe,
On 12/22/14 20:05, Felipe Balbi wrote:
[...]
CONFIG_SCSI_SCAN_ASYNC=y
-CONFIG_ATA=y
-CONFIG_SATA_AHCI_PLATFORM=y
-CONFIG_MD=y
+CONFIG_ATA=m
+CONFIG_SATA_AHCI_PLATFORM=m
Isn't this needed for the rootfs on SATA devices?
CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_ARC is not
18 matches
Mail list logo