Re: [pfSense] WRAP 1D Cases

a metal case for the 1D, Any suggestions? Thanks, Cheyenne ___ List mailing list List@lists.pfsense.org https://lists.pfsense.org/mailman/listinfo/list -- Richard Lussier *inter-node.com* réseaux numériques évolutifs cuivre – sans-fil – fibre

Re: [pfSense] successor to ALIX is here

___ List mailing list List@lists.pfsense.org https://lists.pfsense.org/mailman/listinfo/list -- Richard Lussier *inter-node.com* réseaux numériques évolutifs cuivre – sans-fil – fibre optique t. 514.316.1623 c. 514.574.5111 ___ List mailing list

Re: [pfSense] upgrade dual ALIX netgate box?

On Tue, May 6, 2014 at 3:16 PM, Vick Khera vi...@khera.org mailto:vi...@khera.org wrote: APU2 boards That should be APU1, obviously. APU boards need a heatsink from the bottom. In alix enclosures, the spacing is right for the aluminium block supplied. You will have to check to have

[pfSense] Option 99 : Embedded version or full

Hi, I am installing on a 64bit machine with vga port and keyboard from memstick. I want to use only serial port when installation is finished. Do I have to install embedded version on hard disk to use com port only after install ? What are the differences in performance in the two installs ?

[pfSense] secure management access on transparent bridge firewall

Hi, We are providing Internet access to coop housing (50 units) We have a transit access to the exchange via Fiber and a /26 public IPV4 addresses. I purchased a Netgate C2758 router to be able to do limiter and traffic shaping at rush hour. I did set-up a transparent bridge and everything

Re: [pfSense] secure management access on transparent bridge firewall

Hi Chris, Do you mean to redirect the vpn to the management vlan ? Thank you Richard On 2014-12-08 13:12, Chris L wrote: Management VLAN. On Dec 8, 2014, at 9:08 AM, Richard Lussier richard.luss...@inter-node.com wrote: Hi, We are providing Internet access to coop housing (50 units) We

Re: [pfSense] secure management access on transparent bridge firewall

in the right network. Make sure your bridge has: Block any source BRIDGE0 net dest MGMT net Block any source BRIDGE0 net dest (all pfsense IP addresses) port webmgmt and ssh ports etc... On Dec 8, 2014, at 11:10 AM, Richard Lussier richard.luss...@inter-node.com wrote: Hi Chris, Do you mean

Re: [pfSense] Multi-site openvpn + remote access config challenge

Hi, Sorry for the noise, I found the answer : For the benefit of the list users : A route had to be pushed on each server for the other server's Tun address That is it !! Regards Richard On 2016-02-26 11:53, Richard Lussier wrote: Hi, I already installed a multi-site vpn, 1 server, 4

[pfSense] Multi-site openvpn + remote access config challenge

Hi, I already installed a multi-site vpn, 1 server, 4 clients. Each site can communicate with each other fine. Now I need to give remote access to this network. I installed a remote access server on the site whete the other server is (main site) I can now have access from remote to the server

[pfSense] openvpn site to site clients not communicating ??

Hi, I have a multi site setup with 1 server and 4 clients. v 2.2.6 release The clients have to reach each other. Clients cannot see each others. My wans are set to 1.1.1.2 thru 1.1.1.6 in a simple switch The server is set as described in the pfsense book 21draft : - Local and remote networks

Re: [pfSense] openvpn site to site clients not communicating ??

Hi, This option is not available on a site to site ssl/tls server On 2016-02-18 13:15, Doug Lytle wrote: On Feb 18, 2016, at 1:01 PM, Richard Lussier richard.luss...@inter-node.com wrote: each client connects well to server but wont reach other clients.. any ideas ? On the OpenVPN Server did

Re: [pfSense] openvpn site to site clients not communicating ??

Hi, This option is not available on a site to site ssl/tls server If it's a fully routed network, my next step would be to use traceroute on both ends to see where it's getting hung up at. Doug Got it Doug On the server side, the rule on openvpn destination had to be to "any" instead of