Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread mugginsac
Robert, Thanks. At least it loaded right up as shown on the serial terminal. Now it is at least looking for the ext4 filesystem before loading the ext2 filesystem. Something that I read suggested that the journal-ing stuff on ext4 could shorten the life of the uSD card but that the ext4 has

Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread Robert Nelson
On Mon, Aug 21, 2017 at 4:56 PM, mugginsac wrote: > Here is what I am getting from trying to boot the uSD I built. Is it > possible that I have a bad uSD? > > U-Boot SPL 2017.05 (Aug 20 2017 - 08:57:37) > drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >

Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread Charles Steinkuehler
On 8/21/2017 5:59 PM, mugginsac wrote: > Charles, > > What terminal software are you using? > Is there any special setup required other than 115,200 baud and 8N1 > (data,parity, and stop bits)? > I can't get putty to work with the DE10 and I sometimes get those weird > single column scroll down

Re: [Machinekit] Re: machinekit post processor

2017-08-21 Thread 'Harley Engholm' via Machinekit
The problem appears to be a small amount of flex in the linear rods. I used 8mm rods thinking that the stresses wouldn't very much when used as a drag engraver. I will probably up size the rods to 12mm in the final design version. The 8mm rods would probably be fine for laser engraving. On

Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread mugginsac
Charles, What terminal software are you using? Is there any special setup required other than 115,200 baud and 8N1 (data,parity, and stop bits)? I can't get putty to work with the DE10 and I sometimes get those weird single column scroll down the right hand side with minicom. Alan --

Re: [Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread Charles Steinkuehler
On 8/21/2017 4:56 PM, mugginsac wrote: > Here is what I am getting from trying to boot the uSD I built. Is it > possible that I have a bad uSD? Your uSD is probably fine. There's a CRC error because you don't (yet) have a saved U-Boot environment on the A2 partition. Based on the output you

[Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread mugginsac
Here is what I am getting from trying to boot the uSD I built. Is it possible that I have a bad uSD? U-Boot SPL 2017.05 (Aug 20 2017 - 08:57:37) drivers/ddr/altera/sequencer.c: Preparing to start memory calibration drivers/ddr/altera/sequencer.c: CALIBRATION PASSED

[Machinekit] Re: Will DE0-Nano image work on a DE10-Nano board?

2017-08-21 Thread mugginsac
Taking a break from watching the progress of the solar eclipse. What I am trying to do is get to the point of building a system that will run with HDMI before I start trying to add MachineKit and the hm2 stuff. At the moment the build doesn't seem to run HDMI. I thought I was using the same