Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

Hi, In the beginning i was using 2 dishes on each side. They are ubiquiti 2x2 dual polarized dishes and i connected the chains of station in the same way as AP and i still had issues. After that i thought the problem might be because this card uses mimo multipath and AP ch0 should talk

Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

This is long distance, 5km with 4 dishes on each side. They are all vertical and all chains have signal range -60 to -65. I don't have omni antennas. Is there a problem that i am using dishes? On Wed, Sep 25, 2019 at 5:11 PM +0200, "Ben Greear" wrote: Is this short distance

Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

Hello, Today i managed to connect the station wds at 80MHz channel. Signal is -56 and i have very low datarates. I have attached a photo.  When station was ddwrt and AP openwrt the datarates were 866/433. TX won't do more than VHT-NSS 1 although RX it's not good either because it's a 4 chain

Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

Hi Ben, When do you think you might be able to make those changes to your driver? Thanks, Klevis. On 2019-09-20 13:00, Ben Greear wrote: On 9/20/19 12:55 PM, Vincent Wiemann wrote: Hi Klevis, have you tried it with a short distance? If you did you should better ask Ben Greear directly.

Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

Hi Ben, When do you think you can port those changes to your firmware? Thank you for your support. Klevis. On Fri, Sep 20, 2019 at 10:01 PM +0200, "Ben Greear" wrote: On 9/20/19 12:55 PM, Vincent Wiemann wrote: > Hi Klevis, > > have you tried it wi

Re: [OpenWrt-Devel] QCA9994 outdoor 13km link

Hi Vincent, I have tried short distance with ddwrt and i get 1733/1733 datarates and about 1Gbps real traffic using iperf. Ubiquiti and MikroTik have 80MHz outdoor radios and they work good. I don't want to use 160MHz which is very wide and there are lot of 20MHz channels within that will

[OpenWrt-Devel] QCA9994 outdoor 13km link

Hello everyone, I am trying to setup a custom made outdoor link with Apu2d2 board devices and QCA9994 cards from compex. After i installed openwrt and ath10k ct driver, kmod ath10k and board-2.bin the device can run a 80MHz channel in WDS AP. The problem is that it won't run as station or

Re: [OpenWrt-Devel] [PATCH CC 25/32] ar71xx: compex wpj531 fix setting mac address on ethernet

Do you reckon the same issue is affecting the wpj344? On Tue, 2016-03-01 at 04:06 +0100, Matthias Schiffer wrote: > Signed-off-by: Christian Mehlis > > Backport of r46282 > --- > target/linux/ar71xx/files/arch/mips/ath79/mach-wpj531.c | 11 +-- > > 1 file changed,

Re: [OpenWrt-Devel] 15.05.1 - Chaos Calmer

tifd, procd, uci, rpcd, ubox & uhttpd > * Driver updates > - ledtrig-netdev: fix possible deadlock > - bcm47xxpart: fix bcm53xx booting on NAND with badblocks > - brcmfmac: fix getting/setting TX power, add stations dumping > and > support beamforming >

Re: [OpenWrt-Devel] [PATCH v4 1/2] Add ubnt_hsr platform flag and enable for UniFi Outdoor Plus

The ubnt pro and outdoor+ have a different factory TFTP firmware. Let me know if you need that, however you should be able to recover with the openwrt one. Still digging through the commit loggs for trunk, can't see the patch. Am I missing something? Cheers, A On Mon, 2015-12-14 at 12:54 +0100,