On Fri, 23 Mar 2001 at 00:38:22, Q Branch [EMAIL PROTECTED]
wrote:
(Ref: [EMAIL PROTECTED])
In article [EMAIL PROTECTED], Richard
Zidlicky [EMAIL PROTECTED] writes
SNIP
Minerva supports the higher resolutions so I would think the Amiga emulators
will support them as soon as Minerva will run on
Hi all
I would like to be able to print Text87 documents in a chosen colour. It
should be possible to
send an ESC/P2 code from BASIC to the EPSON Colour Printer before one asks
T87 to print.
Does anyone know the codes to send?
Ian Pizer, 49 ch. Machery, 1292 Chambesy, Geneva.
e-mail [EMAIL
I'm getting puzzled now !
On QPC2v2, and with QLiberator 3.35 I am compiling an old program of mine
which just happens to be Screen Snatcher 2 - because Malcolm wants some
changes made for the new screen resolutions.
I cannot even compile the current working version of the source (unchanged
Two minutes after sending the email below, I realised that the problem was
because I didn't have the easy pointer apendix file for this application
loaded in memory. Its been a while :o)
Please ignore my previous pleas for help. (again !)
Thanks.
Norman.l
On 22 Mar 2001, at 16:46, Marcel Kilgus wrote:
I though you're speaking of data accesses.
The problem, as I'e encountered it, is as follows: You start a
QLiberated job. It hangs. Then you look at it with Jmon. You notice
that it hangs in an infinite loop, at some instrcution which says:
This could be because Qliberator is not able to run under SMSQ properly ; or
it could be because QPC2v2 doesn't like Qliberator; or
it could be both; or
it could be me being a complete idiot :o( ;or
something else altogether
but .
Start QPC2v2 and from a clean boot, (800 by 600 res, high
In article [EMAIL PROTECTED],
Norman Dunbar [EMAIL PROTECTED] writes
I've made my changes to allow Screen Snatcher to grab an entire screen
regardless (?) of the resolution, colour depth etc. Now when I run this
version, I get a 'Value out of range' error as follows :
Job 13 SS3 Line 2160
In article [EMAIL PROTECTED],
Norman Dunbar [EMAIL PROTECTED] writes
Some details snipped !
All of a sudden, I get a screenful of 'ambiguous name' errors. All relating
to Q_ERR_ON/Q_ERR_OFF/Q_ERR/QX etc. The problem stays if I reset the whole
plot, and reload everything as above - now I
This could be because Qliberator is not able to run under SMSQ properly ; or
it could be because QPC2v2 doesn't like Qliberator; or
it could be both; or
it could be me being a complete idiot :o( ;or
something else altogether
but .
Start QPC2v2 and from a clean boot, (800 by 600
- Original Message -
From: Norman Dunbar [EMAIL PROTECTED]
Subject: RE: [ql-users] QLiberator problems - any ideas ?
Two minutes after sending the email below, I realised that the problem was
because I didn't have the easy pointer apendix file for this application
loaded in memory.
Wolfgang Lenerz wrote:
On 20 Mar 2001, at 18:31, Mills wrote:
Dear QLers
Would people be prepared to pay for HB and if so how much, or would
you only use it if was freeware? Would it need certain features before
you would be prepared to buy it? As CSS1/CSS2/XSL are unlikely to be
This could be because Qliberator is not able to run under SMSQ
properly ; or
Unlikely, I never had a problem like this (I use it all the time)
it could be because QPC2v2 doesn't like Qliberator; or
I refer the honourable gentleman to the reply given above ;-)
it could be both; or
it could
Norman Dunbar wrote:
I've made my changes to allow Screen Snatcher to grab an entire
screen
regardless (?) of the resolution, colour depth etc. Now when I run
this
version, I get a 'Value out of range' error as follows :
Job 13 SS3 Line 2160 SCR_YLIM
value out of range
Retry Continue Abort
I would like to be able to print Text87 documents in a chosen colour. It
should be possible to
send an ESC/P2 code from BASIC to the EPSON Colour Printer before one asks
T87 to print.
ESC/P2 code??? I've never used T87 and so don't know how it prints.
Assuming it prints ASCII as opposed to
On 3/23/01 at 8:37 PM Richard Zidlicky wrote:
it seems things are a bit more complicated than a bit 31... UQLX did
support 256 MB years ago but I have turned it off almost immediately
because lots of software (including PE) didn't work with it.
Bye
Richard
Well, I was told that code and data
In article [EMAIL PROTECTED],
Norman Dunbar [EMAIL PROTECTED] writes
I've made my changes to allow Screen Snatcher to grab an entire screen
regardless (?) of the resolution, colour depth etc. Now when I run this
version, I get a 'Value out of range' error as follows :
Job 13 SS3 Line 2160
In article [EMAIL PROTECTED], Tony Firshman
[EMAIL PROTECTED] writes
On Fri, 23 Mar 2001 at 00:38:22, Q Branch [EMAIL PROTECTED]
wrote:
(Ref: [EMAIL PROTECTED])
In article [EMAIL PROTECTED], Richard
Zidlicky [EMAIL PROTECTED] writes
SNIP
Minerva supports the higher resolutions so I would think
17 matches
Mail list logo