@redrun
"But, if you want to access mysb.com from LMS, you can enter your
username and password into LMS, so that the transition back and forth
(mysb<>LMS) is transparent. So, I think, if you have your mysb.com pw
issue sorted, you should be good."
OK. If I open LMS and go to "May account", and
lemmy999 wrote:
> I am 99% sure that it is NOT in the Community Built Firmware.
Then I would think that POMdev should have a separate thread for
wlanpoke
Tony
SBTouch SBRadio
Tony T's Profile:
Tony T wrote:
> Is wlanpoke now included in the Community Built Firmware (so no need to
> install wlanpoke if using it?)
I am 99% sure that it is NOT in the Community Built Firmware.
lemmy999's Profile:
Tony T wrote:
> FWIW, I've been running 3 Vonets for 18mo with the SB Power Supply.
> The VAP11G-3OO can run on 5v, so you can use a PS smaller than 15v if
> you want to power it with a dedicated PS
> (The Vonets has a wide spec of 5VDC to 15VDC, so might be able to handle
> an add'l 3v
I disassembled the radio today to see if I could find the problem. I
found that one of the pins inside the RJ45 jack was slightly bent. I
was able to straighten it enough to get it working again.
The RJ45 jack appears to be a Suyin 101110FS160M474ZA, but I couldn't
find a data sheet for it.
slartibartfast wrote:
> At the moment the Tune in stream only updates the track info if I
> restart it and to confuse things it has reverted to the previous track
> info after displaying the correct info.
>
That is pretty much what I am experiencing. As the track info does
change and show
Tony T wrote:
> Is wlanpoke now included in the Community Built Firmware (so no need to
> install wlanpoke if using it?)
No, I'm pretty sure wlanpoke is *NOT* included in the Community Build
firmware, the Changelog for the build is linked to from this page:
Is wlanpoke now included in the Community Built Firmware (so no need to
install wlanpoke if using it?)
Tony
SBTouch SBRadio
Tony T's Profile: http://forums.slimdevices.com/member.php?userid=34544
View this thread:
lemmy999 wrote:
> I am having some success with wlanpoke, but I tried to play music and
> after about 8 hours I got the red wifi symbol again. I checked the logs
> and during an attempt to reset the wifi, it showed the message "wlanpoke
> exiting" or something like that. ...
> POMDev had
Answer to questions from
'Simplified-instructions-for-Squeezebox-Radio-Wi-Fi-fix'
(https://forums.slimdevices.com/showthread.php?114775-Simplified-instructions-for-Squeezebox-Radio-Wi-Fi-fix-(wlanpoke)=1039680=1#post1039680)
lemmy999 wrote:
> I am having some success with wlanpoke, but I tried
lemmy999 wrote:
> I am having some success with wlanpoke, but I tried to play music and
> after about 8 hours I got the red wifi symbol again. I checked the logs
> and during an attempt to reset the wifi, it showed the message "wlanpoke
> exiting" or something like that. ...
This "wlanpoke
lemmy999 wrote:
> Thanks. I got my Vonets vap11g-300 working so far. But you are correct
> that the instructions leave a lot to be desired. I wanted it to just be
> a bridge, but their instructions result in a bridge and also a wifi
> repeater. Thankfully I found the place to turn off the
Solved I think.
- Rebooted into Max2Play and then downgraded the server to 9.2.
- Installed Patch server and installed version patch to all radios
- Changed VirginMedia box into modem mode
- Set all SB Radios to fixed IP addresses and set to high priority on
Deco mesh system
So
13 matches
Mail list logo
