On Wednesday 17 December 2003 08:28 pm, [EMAIL PROTECTED] wrote:
Get two 486s (cheep enough free anywhere you can find them)or a
little faster machine and set them up to dialup and use Echolink.
You can set it up to only accept connection from the other machine.
73
AC0Y
IRLP boxes can do
You might look into the commercial implementation of IRLP.
http://www.irlp.net/introduction.html It's point to point, IP based and uses
embedded hardware instead of standard PC's. All of these systems including
the NXU-2 boxes you mentioned contain a computer of some sort.
I would stay away
Anyone know if the tk-809 kenwood mobiles can be programmed thru the front
keys? if not anyone have a schematic of the correct programmer for this
little radio?
thanks
KF7NN
Yahoo! Groups Links
To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
To
--- george vagner [EMAIL PROTECTED] wrote:
Anyone know if the tk-809 kenwood mobiles can be
programmed thru the front
keys? if not anyone have a schematic of the correct
programmer for this
little radio?
thanks
KF7NN
It takes the same cable as the other Kenwood
commercial mobiles,
can pass it reliably enough. I have a couple of off brand boxes like the
multitechs that were $150 each. Net2Phone has a 2 port unit that would
require an account with them but, it would not cost to call from unit to
unit. It is $200 ea. here.
Pretty similar to a Cisco ata186. Our club
JOHN MACKEY wrote:
hmmm... I would have to check my books, but didn't the low band
motran use a different channel element than the low band motrac
on transmit? (Or did they BOTH use the TLN-1082?)
I ... hmmm ... I'll have to look. I did some research on that
specific issue some
The only way I have seen to do this is with CTCSS/DCS but, I am not
sure they
can pass it reliably enough. I have a couple of off brand boxes like
the
multitechs that were $150 each. Net2Phone has a 2 port unit that would
require an
account with them but, it would not cost to call from unit
Hi All,
Does anyone have a couple of UHF (suitable for 430Mhz) duplexers surplus to
requirements, and are willing to sell??
These are for a full duplex link at 9Mhz spacing on RX/TX
Please bare in mind the cost for postage as I will require them to be mailed
to New Zealand.
Also I am looking
Neil - Does this include the 12 channel UHF fully solid state
Motran? Which I believe was 16 watts output, called the T44MSN?
(it came with the solid state antenna switch which come people confused for a
duplexer)
Neil McKie [EMAIL PROTECTED] wrote:
SNIP
The UHF Motran uses the 'S'
[EMAIL PROTECTED] wrote:
is called latchup. That is what happens to an CMOS IC when you go
out of MAXIMUM specs on VCC.
This is the only CMOS IC I have had it happen on. Does it on all
varients, 202, 204, 22204 Mc141???.
Yahoo! Groups Links
To visit your group on the web, go to:
Here's the deal
We get about 100 attempted porn posts each week on this reflector. One
of my moderators banned this person and then inadvertently hit the
Approve message button instead of the Reject one. The buttons are
right beside one another and it is EASY to hit the wrong one. This
Hi Everybody!
I have a couple of our Club members that want to experiment with some linking and the RVS-8 voter. They want to play with some cross-banding radios to a few link receivers and then thevoter. After a long discussion I came up with a few questions that I want to ask the group:
1.
12 matches
Mail list logo
