Joerg Reisenweber <[EMAIL PROTECTED]> writes:
> Please note:
> 1) Openmoko does NOT recommend to do this, nor is it usually necessary when
> using the OM-charger or a standard powered host at PC.
> It's a hack for non-OM wallchargers only.
I assume it would also be valid for car chargers like
ht
Hi Andy,
Thanks for a feedback -- I just want to mention again that those are
pure qtopia images -- both kernel and rootfs and without any consecutive
opkg upgrades, so I guess there should be no way I could add any
modules, unless they are in the shipped qtopia image, thus should be
addressed
Jim wrote:
>
> Read the Wiki: http://wiki.openmoko.org/wiki/Booting_from_SD
>
> Make sure the kernel you're using has ext3 built into it. Using ext2 has
> been suggested for the microSD because it will wear it less. In that case
> be sure ext2 is in the kernel. I know the kernel from 7-22-
Read the Wiki: http://wiki.openmoko.org/wiki/Booting_from_SD
Make sure the kernel you're using has ext3 built into it. Using ext2 has
been suggested for the microSD because it will wear it less. In that case
be sure ext2 is in the kernel. I know the kernel from 7-22-2008 has ext2
support in it
Alishams Hassam wrote:
>
>
> Hey, I would try extracting the rootfs from the jffs2 file and placing
> that on the sd card. Instructions here:
> http://wiki.openmoko.org/wiki/Userspace_root_image#Mounting_the_JFFS2_image_on_a_loop_back_device_.28Block_Memory_MTD_Emulation.29
>
>
No luck. Fai
Also to note:
I found the Freerunner not charging (actually it was discharging because it
was on) when it was attached to a USB port on the dock station of a laptop.
I moved the connection to a USB on the laptop and it started charging. I
think some USB ports have lower power or maybe next to non
On Tue, Jul 29, 2008 at 7:17 PM, Joerg Reisenweber <[EMAIL PROTECTED]>wrote:
> Please note:
> 1) Openmoko does NOT recommend to do this, nor is it usually necessary when
> using the OM-charger or a standard powered host at PC.
> It's a hack for non-OM wallchargers only.
> 2) there already is such
Hey, I would try extracting the rootfs from the jffs2 file and placing that on
the sd card. Instructions here:
http://wiki.openmoko.org/wiki/Userspace_root_image#Mounting_the_JFFS2_image_on_a_loop_back_device_.28Block_Memory_MTD_Emulation.29
> "mmcblk0p2" is the ext3 partition on the SD card
Charles Hill wrote:
>> I've used it too, and I'd like to post some notes too (well, isn't there
>> a bugzilla?).
>>
>> However I've found these bugs:
>>
>> - Contacts unfilterable (The keyboard should pop-up like in ASU)
>
> Do you mean by name? Because you can go into the Options menu and limi
Niccolo Rigacci wrote:
>
> I got the same problem, solved flashing a kernel image via the
> U-Boot menu. Here my notes (in Italian, sorry):
> http://www.rigacci.org/wiki/doku.php/doc/appunti/hardware/freerunner#flashing_del_kernel
>
> I got the missing kernel image (uImage-.bin) from the
> ht
Please note:
1) Openmoko does NOT recommend to do this, nor is it usually necessary when
using the OM-charger or a standard powered host at PC.
It's a hack for non-OM wallchargers only.
2) there already is such an app. Please search the wiki for it!
/jOERG
Am Di 29. Juli 2008 schrieb Angus Ain
> e. I was going
> to tabulate the controls, but haven't got to grips with the mediawiki table
> markup yet. I'm open to suggestions!
>
>
>
I was unaware of the cool ALSA mapping, but tried to start a mapping here:
http://wiki.openmoko.org/wiki/Neo_alsamixer
Change it or nuke it as you please.
___
Joerg Reisenweber wrote:
>
> When you plug in charger, Neo *has* to boot up. Then it will charge.
> That's been discussed really exhausting now.
yes, but don't rely so much on the ML, it is quite hard to get
consistent information from here. If I understand well, the situation is
summarized here:
Hi Steven,
i'm sorry, Steven is right.
The headset-plug seem's to have a weird configuration.
___|___|___|__>
1234
1: GND
2: Channel left (right)
3: Channel right (left)
4: mic / switch
Correct me if I'm wrong, but this is incompatible to common stereo jacks.
regar
Hi Karthik,
this sounds like a mechanical issue to me.
Seems like on the phone-jack side only one channel delivers a sound signal.
If you pull it out this one contact connects to both channels of your
earphone.
The result is, that you hear mono-sound on both sides of your earphone.
Try to chang
The thing is, that's not a stereo jack. It's a headset jack. They
have a different number of "rings". It sounds like you don't have the
right plug on your speakers.
-Steven
On Tue, Jul 29, 2008 at 3:59 PM, Karthik Kumar <[EMAIL PROTECTED]> wrote:
> Hi,
>
> I noticed that pushing the stereo jac
Marco Trevisan (Treviño) wrote:
> leonardo wrote:
> > given this, I'd like to know if there is, somewhere, a finger-based
>> (qwerty) keyboard that can be easily used, for example to send sms or
>> write urls. I've found this [1] page which presents something as I
>> whish, but could not find any
Hi,
I noticed that pushing the stereo jack in until there isn't a visible
connector gap doesn't output any sound at all. Playing with alsamixer
won't help as well. I need to pull the connector a few mm back
(typically 2-3mm) to get it to work on both speakers. Do other device
owners have this prob
Al Johnson wrote:
>
> There are 2 reasons for that. First it's work in progress - I haven't worked
> out where everything is yet. Second there is some difficulty adding controls
> that are logical entities in the digital blocks to the picture. I was going
> to tabulate the controls, but haven't
Charles Hill writes:
>
> For some reason I'm not seeing the Screenshot app when using the Software
> Packages app and pointing it at the qtopia.net/packages/feed/4.3.2/neo/
> repository. I see all the other apps, just not Screenshot.
>
> Does anyone have this working? Any ideas?
ok, it should
"Marco Trevisan (Treviño)" writes:
> Charles Hill wrote:
>> I'm currently running Qtopia on my FreeRunner.
>> Version: 4.3.2 snapshot 07221045 Submitted Date 2008/7/24
>
> I've used it too, and I'd like to post some notes too (well, isn't there
> a bugzilla?).
Yes. http://www.trolltech.com/deve
Dan Leinir Turthra Jensen writes:
> Tuesday 29 July 2008 Charles Hill wrote:
>> For some reason I'm not seeing the Screenshot app when using the Software
>> Packages app and pointing it at the qtopia.net/packages/feed/4.3.2/neo/
>> repository. I see all the other apps, just not Screenshot.
>>
>>
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| * Andy Green <[EMAIL PROTECTED]> [2008-07-29 20:42 +0200]:
|> |
|> | When it happens, the (Linux) host won't recognize the Neo as a network
|> | device, and -- more annoying -- the Neo won't fast-charge.
|>
On Tuesday 29 July 2008, H. Rosmanith wrote:
> > >> and if configured correctly, which is:
> > >>> If the PGA and mux are configured, it should work OK.
> > >>
> > >> then /dev/dsp will output PCM data?
> > >
> > > woah, I finally got it to work. I change DAI Mode from "DAI 0"
> > > to "DAI 1" - an
* Andy Green <[EMAIL PROTECTED]> [2008-07-29 20:42 +0200]:
> |
> | When it happens, the (Linux) host won't recognize the Neo as a network
> | device, and -- more annoying -- the Neo won't fast-charge.
> |
> | The only solution I have found is to reboot the FR (and sometimes it
> | isn't enough, las
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| Hi there,
|
| I noticed several times a problem when connecting the FR to a host PC.
|
| When it happens, the (Linux) host won't recognize the Neo as a network
| device, and -- more annoying -- the Neo won't
Hi there,
I noticed several times a problem when connecting the FR to a host PC.
When it happens, the (Linux) host won't recognize the Neo as a network
device, and -- more annoying -- the Neo won't fast-charge.
The only solution I have found is to reboot the FR (and sometimes it
isn't enough, la
>I've used it too, and I'd like to post some notes too (well, isn't there
>a bugzilla?).
>
>However I've found these bugs:
>
> - Contacts unfilterable (The keyboard should pop-up like in ASU)
Do you mean by name? Because you can go into the Options menu and limit the
contacts by Group, as well
> >> and if configured correctly, which is:
> >>> If the PGA and mux are configured, it should work OK.
> >> then /dev/dsp will output PCM data?
> > woah, I finally got it to work. I change DAI Mode from "DAI 0"
> > to "DAI 1" - and suddenly the dsp-device spits out tons o' data.
> >
>
> sweet!
h
>> and if configured correctly, which is:
>>> If the PGA and mux are configured, it should work OK.
>> then /dev/dsp will output PCM data?
> woah, I finally got it to work. I change DAI Mode from "DAI 0"
> to "DAI 1" - and suddenly the dsp-device spits out tons o' data.
>
sweet!
;
--
Jay Vaughan
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| by the way, when reading from dsp with od and changing the
| settings (DAI 0 -> DAI 1), od would zombie and never release
| the device.
|
| a "dmesg" shows why:
|
| Unable to handle kernel NULL pointer deref
Hi,
Am Freitag, den 25.07.2008, 09:49 +0200 schrieb Yorick Moko:
> the body of the messages worked for me in 2007.2
> i could also see the date it was sent, but not the time... very annoying
If you are able to compile your own openmoko-messages, you can find a
patch for that on
http://git.nomeata
Tuesday 29 July 2008 Charles Hill wrote:
> For some reason I'm not seeing the Screenshot app when using the Software
> Packages app and pointing it at the qtopia.net/packages/feed/4.3.2/neo/
> repository. I see all the other apps, just not Screenshot.
>
> Does anyone have this working? Any ideas?
Charles Hill wrote:
> I'm currently running Qtopia on my FreeRunner.
> Version: 4.3.2 snapshot 07221045 Submitted Date 2008/7/24
I've used it too, and I'd like to post some notes too (well, isn't there
a bugzilla?).
However I've found these bugs:
- Contacts unfiltrable (The keyboard should po
by the way, when reading from dsp with od and changing the
settings (DAI 0 -> DAI 1), od would zombie and never release
the device.
a "dmesg" shows why:
Unable to handle kernel NULL pointer dereference at virtual address
pgd = c0004000
[] *pgd=
Internal error: Oops: 0 [#
> and if configured correctly, which is:
> > If the PGA and mux are configured, it should work OK.
> then /dev/dsp will output PCM data?
woah, I finally got it to work. I change DAI Mode from "DAI 0"
to "DAI 1" - and suddenly the dsp-device spits out tons o' data.
that was quite some trial and er
For some reason I'm not seeing the Screenshot app when using the Software
Packages app and pointing it at the qtopia.net/packages/feed/4.3.2/neo/
repository. I see all the other apps, just not Screenshot.
Does anyone have this working? Any ideas?
--
View this message in context:
http://n2.nab
I'm currently running Qtopia on my FreeRunner.
Version: 4.3.2 snapshot 07221045 Submitted Date 2008/7/24
1. Question: When going into the System Info on the phone it says Qtopia
Version 4.3.3, built by lpotter@ on July 22. Which is it, 4.3.2 or 4.3.3?
2. Bug: Speed Dial has no visual feedback o
Hello Andy,
> Somebody in the thread at some point said:
>
> | So, what is required to make the dsp-device delive audio-data?
> |
> | Q: The hardware does support this, right?
>
> Yeah.
>
> | Q: Is it a audio-driver problem, e.g. the alsa-device-driver for the chip
> |doesnt support audio c
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| So, what is required to make the dsp-device delive audio-data?
|
| Q: The hardware does support this, right?
Yeah.
| Q: Is it a audio-driver problem, e.g. the alsa-device-driver for the chip
|doesnt s
hello,
I've got my brandnew neo freefrunner just yesterday, and
have a question about it.
I logged into the ... device via ssh and copied some file
to the audio device, like "dd if=/dev/urandom of=/dev/dsp bs=1k count=100"
This will produce some noise, as expected.
Now I'd like to copy some da
Hello,
Does anyone know if gsmd can be ported to other phones/platforms ?
Regards,
Abdul Hakeem
_
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Martin Walshe
Sent: 20 July 2008 19:37
To: Support for Openmoko Device Owners
Subject: Re: One-sided GSM calls
On Sat, Jul 1
Someone reported the error when saving a screenshot:
"Error saving screenshot: Value for PNG text chunk CREATOR cannot
be converted to ISO-8859-1 encoding"
I got the same error on a FreeRunner OM2007.2 upgraded yesterday.
The screen capture porgram (gpe-scap) fails to open /lib/libc.so,
so I so
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| When performing a 'nand erase rootfs' I get the following:
|
|
| GTA02v5 # nand erase rootfs
|
| NAND erase: device 0 offset 0x96, size 0xf6a
| Skipping bad block at
| 0x
Hey Bob,
When I first installed the matchbox keyboard, I had to go find the
updated libfreetype6 on the web. If you google it you should be able to
find it for our phone with no problem. You'll have to install it
manually, but that would be
opkg install force-update libfreetype6 (i think that's
When performing a 'nand erase rootfs' I get the following:
GTA02v5 # nand erase rootfs
NAND erase: device 0 offset 0x96, size 0xf6a
Skipping bad block at
0x0ff8
Skipping bad block at
0x0ffa
Hi,
I got it done. thanks a lot.
Thanks
Bijoy
> - Original Message -
> From: bijoy franco
> Sent: 29/07/08 12:10 pm
> To: support, Openmoko, sparkymat, Ajith, [EMAIL PROTECTED],
> community, openmoko
> Subject: Flashing Qtopia using Windows XP SP2.
>
>
> Hi,
>
>
>
>
>
Hi Sparky
Am Sonntag, den 27.07.2008, 10:28 +0530 schrieb sparky mat:
> Has someone tried the SettingsGUI on the Freerunner?
I am porting it to the FreeRunner and FSO right now.
> I keep getting the following error:
>
> valueError: invalid literal for int() with base 10: 'on\n'
The error is
Rene Horn wrote:
> Is there a Freerunner/Qtopia package out there somewhere for qpeGPS?
>
> I've been searching for a while now because I really like Qtopia, but
> I've found none--well, at least the package in their download section
> doesn't seem to be compatible with opkg. I'm not even sure
Is there a Freerunner/Qtopia package out there somewhere for qpeGPS?
I've been searching for a while now because I really like Qtopia, but I've
found none--well, at least the package in their download section doesn't
seem to be compatible with opkg. I'm not even sure if that one is even
compatibl
for gtk+ installation i got following errors
/
**configure: error: Package requirements (glib-2.0 >= 2.7.1 atk >= 1.0.1
pango >= 1.9.0 cairo >= 0.9.2) **were not met.Consider adjusting the
PKG_CONFIG
for gtk+ installation i got following errors
/
**configure: error: Package requirements (glib-2.0 >= 2.7.1 atk >= 1.0.1
pango >= 1.9.0 cairo >= 0.9.2) **were not met.Consider adjusting the
PKG_CONFIG
Aaron Sowry wrote:
> I am looking at starting development of a few simple apps in Qt, however
> until the other builds are more stable I would prefer to use the
> Trolltech Qtopia image to test and develop on. However I'm slightly
> concerned that if I do this then these apps won't work on FSO w
On Mon, Jul 28, 2008 at 04:38:25PM -0700, casaubon wrote:
>
> NAND read: device 0 offset 0x8 size 0x20
> 2097152 bytes read:OK
> booting image at 3200
> bad magic number
It seems that the new kernel-image-2.6.24 package does not
contain the actual kernel image (it is just 1.1 kb), so
Hey,
Don't set console to USB. Keep it plugged in, and restart. At the
menu, don't do anything. That worked for me
On Tue, Jul 29, 2008 at 12:10 PM, bijoy franco <[EMAIL PROTECTED]> wrote:
> Hi,
>
> Thanks a lot to all of you guys for helping on this...especially Ajith and
> Rakshat
>
> I have do
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Somebody in the thread at some point said:
| trying the most recent qtopia images (without any additional fixes). On
| boot I mentioned some kernel oopses... here is one (phone was attached
| via usb on boot to the laptop... and now remains attached al
56 matches
Mail list logo