Calling ahab_close cmd for the user to interact for confirmation.
This is not friendly usable when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron
---
arch/arm/mach-imx/imx8/ahab.c | 3 ++-
1 file
Calling ahab_close cmd force the user to interact for confirmation.
This is not user-friendly when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron
---
v2:
- Fix commit log
---
arch/arm/mach-imx/i
Hi Jagan
On Mon, 30 Sep 2019 at 17:48, Jagan Teki wrote:
>
> On Sat, Sep 28, 2019 at 2:54 AM Maxime Ripard
> wrote:
> >
> > Hi,
> >
> > On Fri, Sep 06, 2019 at 09:53:33AM +0200, Clément Péron wrote:
> > > Hi,
> > >
> > > On Sun, 25 A
Hi Andre,
On Wed, 12 Oct 2022 at 18:35, Andre Przywara wrote:
>
> The CherryPi F1C200s board is a small development board, featuring the
> F1C200s with 64MB of co-packaged DRAM. It comes with two USB-C sockets,
> of which one is connected to a USB-UART chip, that provides easy access
> to UART1.
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.
Signed-off-by: Clément Péron
---
arch/arm/mach-imx/parse-container.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-imx/parse-container.c
b/arch/arm
Hi,
I'm on top of U-Boot 2018.11-rc3 and try to boot using TFTP to load a
Kernel 4.9.130
My board is a custom SoCFPGA CycloneV with 512MiB and I try to load :
-zImage (kernel + rootfs) @ 0x100 (the size is around 29MiB kernel
is compressed with gzip)
-DeviceTree @ 0x1800
The SDRAM should
Hi Marek,
On Fri, 2 Nov 2018 at 14:23, Marek Vasut wrote:
>
> On 11/02/2018 02:10 PM, Clément Péron wrote:
> > Hi,
>
> Hi,
>
> > I'm on top of U-Boot 2018.11-rc3 and try to boot using TFTP to load a
> > Kernel 4.9.130
> > My board is a custom So
Hi,
I'm not an expert but regarding commit
b8790ebeec13c882979dc986947397738d9f38aa I think you should drop the
unit-address in its files.
"The DT spec demands a unit-address of a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not
Hi Valentin-catalin,
There is a typo in your commit title.
Regards,
Clement
On Tue, 30 Oct 2018 at 11:44, Valentin-catalin Neacsu
wrote:
>
> Print information about Aquantia firmware loaded on the phy
> Signed-off-by: Valentin Catalin Neacsu
> ---
> drivers/net/phy/aquantia.c | 21 +++
Hi,
On Thu, 1 Nov 2018 at 06:08, AKASHI Takahiro wrote:
>
> On Wed, Oct 31, 2018 at 09:54:14PM +0100, Heinrich Schuchardt wrote:
> > On 10/31/2018 01:22 PM, Alexander Graf wrote:
> > > On 10/31/2018 11:00 AM, Clément Péron wrote:
> > >> Hi,
> > >>
Hi,
Maybe check the GCC option "-mno-unaligned-access"
$>cat arch/arm/cpu/armv7/config.mk
#
# (C) Copyright 2002
# Gary Jennejohn, DENX Software Engineering,
#
# SPDX-License-Identifier: GPL-2.0+
#
# On supported platforms we set the bit which causes us to trap on unaligned
# memory access. Th
ot a maintainer but in this case I would have send a V3 if it's
not merged or send a separate patch if it's already merged.
If you send a V3, don't forget to add the "Reviewed-by" tags.
Regards,
Clement
>
> Regards,
> Philippe
>
>
> - Mail origin
ified.
Here, you introduce a new patch in your serie and Simon didn't review
it, so you should not add a "Reviewed-by' on this commit !
> Reviewed-by: Clément Péron
Also I don't gave you my "Reviewed-by" tag, only made a comment about
the its format, so you should no
Hi Thomas,
On Fri, 21 Sep 2018 at 19:09, Dalon L Westergreen
wrote:
>
> On Thu, 2018-09-20 at 09:25 -0400, Thomas Epperson wrote:
> > I've done some troubleshooting on warm resets and determined that the
> > ocramis
> > not being set correctly for warm reset to run properly (it hangs
> > thepro
Hi Ansuel,
I made the ipq4018 works (with ethernet and spi) on 2017.07.
there is a more recent version of U-boot for ipq806x here :
https://source.codeaurora.org/quic/qsdk/oss/boot/u-boot-2016/
Regards,
Clement
2018-02-02 1:03 GMT+01:00 Ansuel Smith :
> I have source of an old version of uboo
Hi,
I'm working on a dev board the SoC is Broadcom Cygnus with 256MiB of RAM
Booting a Kernel and device tree works fine.
But booting a Kernel with initramfs and a device tree make a strange behavior.
Don't want to say stupid things but It seems that the Kernel didn't
find the device tree and try
Replying to myself
2018-02-21 17:16 GMT+01:00 Clément Péron :
> Hi,
>
> I'm working on a dev board the SoC is Broadcom Cygnus with 256MiB of RAM
> Booting a Kernel and device tree works fine.
> But booting a Kernel with initramfs and a device tree make a strange behavior.
&
Hi,
Is it possible to have one kernel entry in a FIT image with two
different load/entry point.
I have 2 boards which share the same kernel but doesn't have the same
entry/load point.
Thanks,
Clement
___
U-Boot mailing list
U-Boot@lists.denx.de
https:/
Hi Peter,
> Not sure if it does exactly what you need but the pine64 board supports
> multiple boards with different device trees for each board in the fit image.
>
> Peter
No it's not why I need, I was looking to do something like this but
without doubling the size :
kernel-bcm {
> I think what you want is to use kernel_noload and then load/entry values
> are ignored and we use the kernel in-place.
Yes, I will try that
Thanks,
Clement
___
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
The signature/hash information are displayed for images but nor for
configurations.
Add subnodes printing in fit_conf_print() like it's done in fit_image_print()
---
common/image-fit.c | 11 +++
1 file changed, 11 insertions(+)
diff --git a/common/image-fit.c b/common/image-fit.c
index 4
Hi,
I try to update my u-boot with the latest version 2017.07.
My board is an Altera SocFPGA CycloneV and I have a mv88e61xx switch.
My board is working fine except I got an issue with the new switch driver.
If autoneg is set to enable, negotation never complete and i got a timeout.
If I let the
the reset flag should be written without
other bits set. Writing the current state will lead to restoring the
state of the PHY (e.g. Powerdown), which is not what is expected from
a software reset."
Regards,
Clement
2017-08-31 11:12 GMT+02:00 Clément Péron :
> Hi,
>
> I
Hi Chris,
> Does that mean with this commit reverted your board is working?
Yes, it's fixed the auto negotiation.
> I have some older boards using a 88e6097 (compatible with 88e61xx).
> I've been looking for an excuse to get them working against the latest
> u-boot. Last time I tried the new 88e6
Hi,
I got also somme issue with my QSPI on CycmoneV and u-boot 2017.07
I cherry-picked commits from Jason Rush :
b90ce1c29023abe730d2b4174294bdc09acef3e0
836a0278476be94c95ff084f81c2302fc5c0265c
b0eac7e0d1e4817388543b58d30b322d0bac49a8
Also i forgot to put the
"u-boot,dm-pre-reloc;" in my device
Sorry these are my local commits you can find them here :
https://patchwork.ozlabs.org/patch/765992/
https://patchwork.ozlabs.org/patch/765996/
https://patchwork.ozlabs.org/patch/765997/
https://patchwork.ozlabs.org/patch/765998/
2017-09-22 14:12 GMT+02:00 Clément Péron :
> Hi,
>
> I
Hi,
I write a script on u-boot but i found 2 strange behaviors.
The first one is when I try to do a mask from a memory address and
store it to an env variable.
=> setexpr toto *{loadaddr} & 0xFF
syntax error
=> setexpr toto *{loadaddr} & 0x3F
syntax error
=> setexpr toto 0x3F & *{loadaddr}
synt
Dear Wolfgang Denk,
Thanks a lot for your explanations !
Clement
> I'm tempted to rephrase: you made some errors :-)
>> The first one is when I try to do a mask from a memory address and
>> store it to an env variable.
>>
>> => setexpr toto *{loadaddr} & 0xFF
>> syntax error
>> => setexpr toto
Hi Simon,
> Disable the data cache tooI change the "compatible" string of the flash chip
from "n25q00" to "spi-flash".
Yes, missed to mention these steps.
Did you also test the saveenv and sf unlock ?
Did you get some strange behaviors after a "warm reboot" from linux ?
A week that i'm using a n
Hi,
My issue is with the eMMC after the boot from linux 3.12 and a warm reboot.
The eMMC is stuck in an infinite loop after CMD8 small trace of the
eMMC cmds sent:
Sending CMD0
Sending CMD8
dwmci_send_cmd: Response Timeout.
Sending CMD55
dwmci_send_cmd: Response Timeout.
Sending CMD0
Sending CMD1
> I think this is fine, but can you please re-post with a Signed off by
> line? Thanks!
> --
> Tom
Yes I will, and also missed to substitute "image" by "configuration" in the
comments,
Thanks,
Clement
___
U-Boot mailing list
U-Boot@lists.denx.de
https
Got same issue recently and sent the explanation :
https://lists.denx.de/pipermail/u-boot/2018-February/321060.html
You can try to enable early_printk and confirm if it's the same issue,
Regards,
Clément
Le lun. 30 avr. 2018 à 16:15, josh phelps a
écrit :
> Hello All,
> Im booting Linux on arm6
Hi,
I'm looking to add the public key for the FitImage signature in my dts.
Do you know if there is a script to add the pubkey in the .dts and not in
the .dtb ?
Actually I "decompile" the .dtb to get those values, but maybe there is an
easier way.
Looking to generate something like this from th
Hi Andre,
On Tue, 18 Jun 2019 at 09:50, Jagan Teki wrote:
>
> On Thu, May 16, 2019 at 6:56 AM Andre Przywara wrote:
> >
> > Hi,
> >
> > this series enables USB support on the H6 boards. This is mostly just
> > adding some missing pieces here and there, the actual controller and PHY
> > are very
Hi,
On Thu, 16 May 2019 at 03:27, Andre Przywara wrote:
>
> The first USB controller on the H6 SoC shares a PHY with the OTG
> controller. Reportedly to avoid problems with the VBUS regulator under
> Linux, we don't link OHCI0/EHCI0 to the USB PHY in the H6 .dtsi file.
>
> However on boards which
Hi,
On Thu, 16 May 2019 at 03:27, Andre Przywara wrote:
>
> The USB PHY used in the Allwinner H6 SoC has some pecularities (as usual),
Checkpatch warning:
WARNING: 'pecularities' may be misspelled - perhaps 'peculiarities'?
> which require a small addition to the USB PHY driver:
> In this case
On Tue, 18 Jun 2019 at 19:08, Clément Péron wrote:
>
> Hi Andre,
>
> On Tue, 18 Jun 2019 at 09:50, Jagan Teki wrote:
> >
> > On Thu, May 16, 2019 at 6:56 AM Andre Przywara
> > wrote:
> > >
> > > Hi,
> > >
> > > this series enab
Hi André,
On Wed, 19 Jun 2019 at 03:04, André Przywara wrote:
>
> On Tue, 18 Jun 2019 19:22:34 +0200
> Clément Péron wrote:
>
> Hi,
>
>
> > On Tue, 18 Jun 2019 at 19:08, Clément Péron wrote:
> > >
> > > Hi Andre,
> > >
> &
Hi Andre,
On Wed, 19 Jun 2019 at 03:12, Andre Przywara wrote:
>
> The Eachlink H6 Mini is a modestly priced TV box, using the Allwinner H6
> SoC. It comes with 4GB of DRAM (3GB usable) and 32GB of eMMC in the
> typical TV box enclosure.
> This adds a basic device tree and defconfig for it.
>
> It
HI André,
On Wed, 19 Jun 2019 at 12:03, Andre Przywara wrote:
>
> On Wed, 19 Jun 2019 10:57:14 +0200
> Clément Péron wrote:
>
> Hi,
>
> > On Wed, 19 Jun 2019 at 03:04, André Przywara wrote:
> > >
> > > On Tue, 18 Jun 2019 19:22:34 +0200
Hi André,
On Thu, 20 Jun 2019 at 23:18, André Przywara wrote:
>
> On 20/06/2019 19:01, Clément Péron wrote:
>
> Hi Clément,
>
> thanks for trying that!
> ...
>
> > On Wed, 19 Jun 2019 at 12:03, Andre Przywara wrote:
> >>
> >> On Wed, 19 J
Hi,
On Fri, 12 Apr 2019 at 15:36, Jagan Teki wrote:
>
> On Mon, Apr 8, 2019 at 10:11 PM Clément Péron wrote:
> >
> > There is only one muxing avalaible for each MMC controller.
> >
> > Move this pinmux to the SOC dtsi.
>
> Sync all dts(i) changes in one
This serie introduce the Beelink GS1 board with a patch for
the reset on Allwinner H6.
Thanks to Jagan Teki most of the Beelink GS1 device-tree is
taken from the Orange Pi boards.
Changes with v1:
- Add bus-width for mmc2 node
- Add sha1 in the sync dts commit
Clément Péron (3):
arm: dts
armv8' compatible
string
Signed-off-by: Clément Péron
---
arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 --
arch/arm/dts/sun50i-h6-pine-h64.dts | 4
arch/arm/dts/sun50i-h6.dtsi | 16 ++--
3 files changed, 10 insertions(+), 12 deletions(-)
diff --git a/arch/arm/dts
(RTL8222BS)
Signed-off-by: Clément Péron
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +
configs/beelink_gs1_defconfig | 15 ++
3 files changed, 200 insertions(+)
create mode 100644 arch/arm/dts/sun50i-h6
WDOG is broken for some H6 rev. The board is not
reseted correctly.
Use the R_WDOG instead.
Signed-off-by: Clément Péron
---
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
arch/arm/mach-sunxi/board.c | 9 +++--
2 files changed, 8 insertions(+), 2 deletions
Hi,
On Sun, 14 Apr 2019 at 19:29, Jagan Teki wrote:
>
> On Fri, Apr 12, 2019 at 7:45 PM Clément Péron wrote:
> >
> > Beelink GS1 is an Allwinner H6 based TV box,
> > which support:
> > - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> > - GPU Mali-T720
th v2:
- Add myself in sunxi MAINTAINERS file
- Update with Jagan Teki's rsync patch
- Change to complete DTS same as linux
- Add linux sha1 to the commit log
Changes with v1:
- Add bus-width for mmc2 node
- Add sha1 in the sync dts commit
Clément Péron (2):
arm: dts: h6: Add Beelink G
(RTL8222BS)
Introduced in Linux with commit :
089bee8dd119 arm64: dts: allwinner: h6: Introduce Beelink GS1 board
Signed-off-by: Clément Péron
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 260 +
board/sunxi/MAINTAINERS
WDOG is broken for some H6 rev. The board is not
reseted correctly.
Use the R_WDOG instead.
Signed-off-by: Clément Péron
---
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
arch/arm/mach-sunxi/board.c | 9 +++--
2 files changed, 8 insertions(+), 2 deletions
cription"
(sha1: 59a9c39544cd1e5952c2a33028d71aa8180648f8)
Part of the sync initiated by 'Clément Péron'.
Signed-off-by: Clément Péron
Signed-off-by: Jagan Teki
---
arch/arm/dts/sun50i-h6-orangepi.dtsi | 62 +++-
arch/arm/dts/sun50i-h6-pine-h64.dts| 88 -
arch/arm/dts/sun50
Hi,
+Chen-Yu Tsai for test and +Icenowy because she try to contact AW
about this issue.
On Wed, 17 Apr 2019 at 19:41, Clément Péron wrote:
>
> WDOG is broken for some H6 rev. The board is not
> reseted correctly.
>
> Use the R_WDOG instead.
The issue is real except on Pine H64
Hi,
On Fri, 19 Apr 2019 at 10:24, Jagan Teki wrote:
>
> On Fri, Apr 19, 2019 at 1:23 PM Clément Péron wrote:
> >
> > Hi,
> >
> > +Chen-Yu Tsai for test and +Icenowy because she try to contact AW
> > about this issue.
> >
> > On Wed, 17 Apr 2019
Hi Jagan,
FYI the patch on ATF has been merged just now. It has been tested by
André Przywara on A64, H5 and H6.
https://github.com/ARM-software/arm-trusted-firmware/commit/523ab5be1a84e9aa15fb62c3a15a6338b01d3961
Thanks,
Clement
On Fri, 19 Apr 2019 at 11:19, Clément Péron wrote:
>
&
(RTL8222BS)
Signed-off-by: Clément Péron
---
This is based on Jagan Teki works for the OrangePi One Plus.
This board is closed source and some regulators may be wrong.
The sys_config.fex is available here: https://pastebin.com/TdnfRMJL
U-Boot bootlog is available here: https://pastebin.com
Hi,
Please Ignore this patch I will resend a new serie.
Thanks,
Clement
On Mon, 1 Apr 2019 at 16:23, Clément Péron wrote:
>
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3
This serie introduce the Beelink GS1 board with a patch for
the reset on Allwinner H6.
Thanks to Jagan Teki most of the Beelink GS1 device-tree is
taken from the Orange Pi boards.
Clément Péron (4):
arm: dts: h6: move MMC pinctrl to soc
arm: dts: h6: Add Beelink GS1 initial support
arm
There is only one muxing avalaible for each MMC controller.
Move this pinmux to the SOC dtsi.
Signed-off-by: Clément Péron
---
arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 --
arch/arm/dts/sun50i-h6-pine-h64.dts | 4
arch/arm/dts/sun50i-h6.dtsi | 4
3 files changed, 4
There are some minor differences between U-Boot and Linux.
Sync only the minor changes.
Signed-off-by: Clément Péron
---
arch/arm/dts/sun50i-h6.dtsi | 12 ++--
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi
index
(RTL8222BS)
Signed-off-by: Clément Péron
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 183 +
configs/beelink_gs1_defconfig | 15 ++
3 files changed, 199 insertions(+)
create mode 100644 arch/arm/dts/sun50i-h6
WDOG in H6 is broken so the reset is actually not working.
Use the R_WDOG instead.
Signed-off-by: Clément Péron
---
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
arch/arm/mach-sunxi/board.c | 9 +++--
2 files changed, 8 insertions(+), 2 deletions(-)
diff --git
+Chen-Yu.
I would like to fix the reset using the R_WDOG instead of WDOG.
What do you think?
If it's acceptable I will propose a similar patch on ATF.
Regards,
Clement
On Mon, 8 Apr 2019 at 18:41, Clément Péron wrote:
>
> WDOG in H6 is broken so the reset is actually not working.
Hi,
On Mon, 8 Apr 2019 at 18:47, Clément Péron wrote:
>
> +Chen-Yu.
>
> I would like to fix the reset using the R_WDOG instead of WDOG.
>
> What do you think?
Adding information about the issue as explained on ATF:
"
There seems to have a HW errata in the new revision of
Hi,
On Mon, 8 Apr 2019 at 18:41, Clément Péron wrote:
>
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - 16GB eMMC
> - AXP805 PMIC
> - 1Gbps GMAC via RTL821
Hi Jagan,
Is there anything you need to merge this patch?
Thanks,
Clément
On Mon, 29 Apr 2019 at 22:28, Clément Péron wrote:
>
> Hi Jagan,
>
> FYI the patch on ATF has been merged just now. It has been tested by
> André Przywara on A64, H5 and H6.
>
> https://github
On Sun, 12 May 2019 at 20:23, Jagan Teki wrote:
>
> On Fri, Apr 19, 2019 at 2:49 PM Clément Péron wrote:
> >
> > Hi,
> >
> > On Fri, 19 Apr 2019 at 10:24, Jagan Teki wrote:
> > >
> > > On Fri, Apr 19, 2019 at 1:23 PM Clément Péron
> > >
Hi Jagan,
On Tue, 14 May 2019 at 15:49, Jagan Teki wrote:
>
> On Wed, Apr 17, 2019 at 11:11 PM Clément Péron wrote:
> >
> > WDOG is broken for some H6 rev. The board is not
> > reseted correctly.
> >
> > Use the R_WDOG instead.
>
> Can you describe
Hi Jonas,
On Tue, 14 May 2019 at 17:41, Jonas Smedegaard wrote:
>
> I notice that the patch to initially support Beelink GS1 was proposed
> before git commit f89d613 changing location of CONFIG_SPL_TEXT_BASE but
> was applied _after_ that commit.
>
> This is similar to the introduction of Olimex
Hi Jagan,
On Mon, 20 May 2019 at 18:34, Jagan Teki wrote:
>
> On Tue, May 14, 2019 at 11:56 PM wrote:
> >
> > From: Clément Péron
> >
> > SPL_TEXT_BASE has been moved to Kconfig with commit:
> > f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
>
Hi Jagan,
On Mon, 20 May 2019 at 18:38, Jagan Teki wrote:
>
> On Mon, May 20, 2019 at 10:07 PM Clément Péron wrote:
> >
> > Hi Jagan,
> >
> > On Mon, 20 May 2019 at 18:34, Jagan Teki wrote:
> > >
> > > On Tue, May 14, 2019 at 11:5
Hi Marcus,
On Sun, 26 May 2019 at 16:57, wrote:
>
> From: Marcus Cooper
>
> The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receive
Sync Kernel DTS for Allwinner H6 boards.
commit Linux 5.3-rc4
Signed-off-by: Clément Péron
---
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++
arch/arm/dts/sun50i-h6-pine-h64.dts| 12
arch/arm/dts/sun50i-h6.dtsi| 43 ++-
3 files changed
Hi
On Sun, 11 Aug 2019 at 22:42, Clément Péron wrote:
>
> Sync Kernel DTS for Allwinner H6 boards.
>
> commit Linux 5.3-rc4
>
> Signed-off-by: Clément Péron
> ---
> arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++
> arch/arm/dts/sun
Sync Kernel DTS for Allwinner H6 boards.
Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
commit Linux 5.3-rc4
Signed-off-by: Clément Péron
---
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++
arch/arm/dts/sun50i-h6-pine-h64.dts| 12
arch/ar
Hi,
On Sun, 25 Aug 2019 at 18:04, Clément Péron wrote:
>
> Sync Kernel DTS for Allwinner H6 boards.
This sync avoid the random mac on the beelink GS1.
Could you check if it's ok for you ?
Thanks,
Clément
>
> Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
Hi,
On Mon, 11 Mar 2024 at 11:38, Kamil Kasperski wrote:
>
> Hello Andre,
> Thanks for your reply and thanks for pointing some stuff out.
>
> > What is "mbox"? Do you have any more information about this vendor?
>
> "MBOX" refers to the "Model" string from system properties.
> The problem is that
76 matches
Mail list logo