For starting up and shutting down my Raspberry Pi (a 3B+ running pCP
with LMS), I have set it up with one of the 'Pimoroni OnOff SHIMs'
(https://shop.pimoroni.com/products/onoff-shim). It looks as though you
can solder it directly to the GPIO pins and still fit a DAC HAT on top
(though I haven't
Squeezelite cannot start until the Bluetooth device is connected. So
you are in a catch22. You can initiate a connection from the pCP web
interface, that would start squeezelite automatically.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Now it works!
THANKS! :)
imi11's Profile: http://forums.slimdevices.com/member.php?userid=70855
View this thread: http://forums.slimdevices.com/showthread.php?t=108410
___
unix
Jeff07971 wrote:
> Use a 38Khz type IR Receiver, Examples being TSOP38238 and TSOP38438
> (There are other types that work fine) I personally use the TSOP38438
>
> https://www.vishay.com/search?searchChoice=part=tsop38438
>
> Wire this to 0V (Pin 20), +3v3 (Pin17) and GPIO25 (Pin 22) and then
Cured wrote:
>
> I already did some research on the web and found out that the
> GPIO-connectors could be of some help. I already bought a normally open
> button (I already soldered two female GPIO-wires to it) but I dont know
> how to connect it to the Allo Boss which is on top of the
imi11 wrote:
> Which receiver should I use?
Use a 38Khz type IR Receiver, Examples being TSOP38238 and TSOP38438
(There are other types that work fine) I personally use the TSOP38438
https://www.vishay.com/search?searchChoice=part=tsop38438
Wire this to 0V (Pin 20), +3v3 (Pin17) and GPIO25
paul- wrote:
> The Squeezebox remote should have worked without modifications.
Which receiver should I use?
imi11's Profile: http://forums.slimdevices.com/member.php?userid=70855
View this thread:
Hello,
Im completely new here and have little technical knowledge. I
recently bought a Raspberry Pi with an Allo Boss 1.2 DAC. I managed to
get it running with PiCorePlayer and LMS. I was so proud!
Currently I use the webinterface of PiCorePlayer to shut it down and
then power it off by
eldrik wrote:
> Thx, figured it out how to use bluetooth.cgi for achieving it :)
>
> Regards
> Eldrik
I'd be grateful if you could you explain how you did this, as I would
like to do something similar?
Thanks, Anthony
Hi,
I use Squeezelite with my sound bar shared with my TV.
When I start my TV, bluetooth is disconnected from Squeezelite... Is
there a way to connect my sound bar on each Squeezelite start (from LMS)
?
Thx.
llaumgui's
The Squeezebox remote should have worked without modifications.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Please 'donate'
That's perfect - just what I needed - thanks!
Squeezebox Radio using LMS 8.0.0 running under piCorePlayer
6.1.0
AlecSp's Profile: http://forums.slimdevices.com/member.php?userid=42763
View this thread:
I have this kind of pc remote:
https://www.aliexpress.com/item/32768227947.html
imi11's Profile: http://forums.slimdevices.com/member.php?userid=70855
View this thread:
Hello,
I use picoreplayer with jivelite. I use universal pc remote.
The player works with this remote with jivelite and with lirc ir setup
either.
BUT I would like to use my original squeezebox touch remote and I'm not
able to set it up.
1. Is the linked remote's usb receiver good to receive
Nothing should have changed. Is the card being detected?
You might need to check the volume setting. You will have to do that
through an ssh session and Alsa mixer. There are basic instructions on
the card control page.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage:
Hi, I have built a weather resistant pCP for a covered patio, all good.
A little fiddling was required to get the Output settings and the Alsa
ttable map to work but achieved using the web gui.
However adding in the 10 band eq removes the mono setting.
Has anybody got any experience they are
16 matches
Mail list logo
