[ovirt-users] jumbo frames inside vm best practices?
Hello, I'm testing an Oracle RAC with 2 Oracle Linux VMs inside a 4.0.6 environment. They run on two different hosts I would like to configure RAC intracluster communication with jumbo frames. At VM level network adapter is eth1 (mapped to a vlan 95 at oVirt hosts side) At oVirt side I configured a vm enabled vlan with mtu=9000 I verified that at hosts side I have vlan95: flags=4163 mtu 9000 ether 00:1c:c4:ab:be:ba txqueuelen 1000 (Ethernet) RX packets 61706 bytes 3631426 (3.4 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 258 (258.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 And able to do a ping -M do -s 8972 ip from each host to the other one In VMs I configure the same MTU=9000 in ifcfg-eth1 But actually inside VMs it works erratically: the same ping test is ok between the VMs but Oracle checks sometimes work and sometimes give error on communication. At initial cluster config, the second node fails to start the cluster. I tried 5-6 times and also tried then to set mtu=8000 inside the VMs, supposing some sort of inner overhead to consider (such as 2 times 28 bytes) but nothing. As soon as I set MTU=1500 at VM side, the cluster is able to form without any problem. I can survive without jumbo frames in this particular case, because this is only a test, but the question remains about eventual best practices to put in place if I want to use jumbo frames. One thing I see is that at VM side I see many drops when interface mtu was 9000, such as eth1 Link encap:Ethernet HWaddr 00:1A:4A:17:01:57 inet addr:192.168.10.32 Bcast:192.168.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:93046 errors:0 dropped:54964 overruns:0 frame:0 TX packets:26258 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:25726242 (24.5 MiB) TX bytes:33573207 (32.0 MiB) at host side I see drops at bond0 level only: [root@ovmsrv05 ~]# brctl show bridge namebridge idSTP enabledinterfaces ;vdsmdummy;8000.no vlan1008000.001cc446ef73nobond1.100 vlan658000.001cc446ef73nobond1.65 vnet0 vnet1 vlan958000.001cc4abbebanobond0.95 vnet2 bond0: flags=5187 mtu 9000 ether 00:1c:c4:ab:be:ba txqueuelen 1000 (Ethernet) RX packets 2855175 bytes 3126868334 (2.9 GiB) RX errors 0 dropped 11686 overruns 0 frame 0 TX packets 1012849 bytes 478702140 (456.5 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 bond0.95: flags=4163 mtu 9000 ether 00:1c:c4:ab:be:ba txqueuelen 1000 (Ethernet) RX packets 100272 bytes 27125992 (25.8 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 42355 bytes 40833904 (38.9 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 vlan95: flags=4163 mtu 9000 ether 00:1c:c4:ab:be:ba txqueuelen 1000 (Ethernet) RX packets 62576 bytes 3719175 (3.5 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 258 (258.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 vnet2: flags=4163 mtu 9000 inet6 fe80::fc1a:4aff:fe17:157 prefixlen 64 scopeid 0x20 ether fe:1a:4a:17:01:57 txqueuelen 1000 (Ethernet) RX packets 21014 bytes 24139492 (23.0 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 85777 bytes 21089777 (20.1 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 [root@ovmsrv05 ~]# cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: enp3s0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: enp3s0 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1c:c4:ab:be:ba Slave queue ID: 0 Slave Interface: enp5s0 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1c:c4:ab:be:bc Slave queue ID: 0 Any hint? Thanks in advance, Gianluca ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] [Call for feedback] did you install/update to 4.1.0?
https://bugzilla.redhat.com/show_bug.cgi?id=1419352 Done. *** Dr. Arman Khalatyan eScience -SuperComputing Leibniz-Institut für Astrophysik Potsdam (AIP) An der Sternwarte 16, 14482 Potsdam, Germany *** On Sun, Feb 5, 2017 at 8:55 PM, Nir Soffer wrote: > On Sun, Feb 5, 2017 at 9:39 PM, Arman Khalatyan wrote: > >> All upgrades are went smoothly! Thanks for the release. >> There is an minor problem I saw: >> After upgrading from 4.0.6 to 4.1 the GUI dialog for moving the disks >> from one Storage to another is not rendered correctly when multiple >> disks(>8) are selected for move. >> please see the attachment: >> >> > > Thanks for reporting this, would you file a bug? > https://bugzilla.redhat.com/enter_bug.cgi?product=ovirt-engine > > >> >> >> *** >> >> Dr. Arman Khalatyan eScience -SuperComputing >> Leibniz-Institut für Astrophysik Potsdam (AIP) >> An der Sternwarte 16, 14482 Potsdam, Germany >> >> *** >> >> On Sat, Feb 4, 2017 at 5:08 PM, Martin Perina wrote: >> >>> >>> >>> On Fri, Feb 3, 2017 at 9:24 AM, Sandro Bonazzola >>> wrote: >>> On Fri, Feb 3, 2017 at 9:14 AM, Yura Poltoratskiy < yurapolt...@gmail.com> wrote: > I've done an upgrade of ovirt-engine tomorrow. There were two > problems. > > The first - packages from epel repo, solved by disable repo and > downgrade package to an existing version in ovirt-release40 repo (yes, > there is info in documentation about epel repo). > > The second (and it is not only for current version) - run the > engine-setup always not complete successfully because cat not start > ovirt-engine-notifier.service after upgrade, and the error in notifier is > that there is no MAIL_SERVER. Every time I am upgrading engine I have the > same error. Than I add MAIL_SERVER=127.0.0.1 to > /usr/share/ovirt-engine/services/ovirt-engine-notifier/ovirt-engine-notifier.conf > and start notifier without problem. Is it my mistake? > >>> Please never change anything in /usr/share/ovirt-engine, those files >>> are always overwritten during upgrade. If you need change any option in >>> ovirt-engine-notifier, please create new configuration file in >>> /etc/ovirt-engine/notifier/notifier.conf.d directory. For example if >>> you need to set MAIL_SERVER please create >>> /etc/ovirt-engine/notifier/notifier.conf.d/99-custom.conf >>> with following content: >>> >>> MAIL_SERVER=127.0.0.1 >>> >>> After saving the file please restart ovirt-engine-notifier service: >>> >>> systemctl restart ovirt-engine-notifier >>> >>> Adding Martin Perina, he may be able to assist you on this. > And one more question. In Events tab I can see "User vasya@internal > logged out.", but there are no message that 'vasya' logged in. Could > someone tell me how to debug this issue? > >>> Please share complete log to analyze this, but this user may be logged >>> in before upgrade and we just clean its session after upgrade. >>> >>> >>> Martin can probably help as well here, adding also Greg and Alexander. > > 02.02.2017 14:19, Sandro Bonazzola пишет: > > Hi, > did you install/update to 4.1.0? Let us know your experience! > We end up knowing only when things doesn't work well, let us know it > works fine for you :-) > > If you're not planning an update to 4.1.0 in the near future, let us > know why. > Maybe we can help. > > Thanks! > -- > Sandro Bonazzola > Better technology. Faster innovation. Powered by community > collaboration. > See how it works at redhat.com > > > ___ > Users mailing > listUsers@ovirt.orghttp://lists.ovirt.org/mailman/listinfo/users > > > > ___ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > > -- Sandro Bonazzola Better technology. Faster innovation. Powered by community collaboration. See how it works at redhat.com >>> >>> >>> ___ >>> Users mailing list >>> Users@ovirt.org >>> http://lists.ovirt.org/mailman/listinfo/users >>> >>> >> >> ___ >> Users mailing list >> Users@ovirt.org >> http://lists.ovirt.org/mailman/listinfo/users >> >> > ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] [Call for feedback] did you install/update to 4.1.0?
On Sun, Feb 5, 2017 at 9:39 PM, Arman Khalatyan wrote: > All upgrades are went smoothly! Thanks for the release. > There is an minor problem I saw: > After upgrading from 4.0.6 to 4.1 the GUI dialog for moving the disks from > one Storage to another is not rendered correctly when multiple disks(>8) > are selected for move. > please see the attachment: > > Thanks for reporting this, would you file a bug? https://bugzilla.redhat.com/enter_bug.cgi?product=ovirt-engine > > > *** > > Dr. Arman Khalatyan eScience -SuperComputing > Leibniz-Institut für Astrophysik Potsdam (AIP) > An der Sternwarte 16, 14482 Potsdam, Germany > > *** > > On Sat, Feb 4, 2017 at 5:08 PM, Martin Perina wrote: > >> >> >> On Fri, Feb 3, 2017 at 9:24 AM, Sandro Bonazzola >> wrote: >> >>> >>> >>> On Fri, Feb 3, 2017 at 9:14 AM, Yura Poltoratskiy >> > wrote: >>> I've done an upgrade of ovirt-engine tomorrow. There were two problems. The first - packages from epel repo, solved by disable repo and downgrade package to an existing version in ovirt-release40 repo (yes, there is info in documentation about epel repo). The second (and it is not only for current version) - run the engine-setup always not complete successfully because cat not start ovirt-engine-notifier.service after upgrade, and the error in notifier is that there is no MAIL_SERVER. Every time I am upgrading engine I have the same error. Than I add MAIL_SERVER=127.0.0.1 to /usr/share/ovirt-engine/services/ovirt-engine-notifier/ovirt-engine-notifier.conf and start notifier without problem. Is it my mistake? >>> >> Please never change anything in /usr/share/ovirt-engine, those files are >> always overwritten during upgrade. If you need change any option in >> ovirt-engine-notifier, please create new configuration file in >> /etc/ovirt-engine/notifier/notifier.conf.d directory. For example if you >> need to set MAIL_SERVER please create >> /etc/ovirt-engine/notifier/notifier.conf.d/99-custom.conf >> with following content: >> >> MAIL_SERVER=127.0.0.1 >> >> After saving the file please restart ovirt-engine-notifier service: >> >> systemctl restart ovirt-engine-notifier >> >> >>> Adding Martin Perina, he may be able to assist you on this. >>> >>> >>> And one more question. In Events tab I can see "User vasya@internal logged out.", but there are no message that 'vasya' logged in. Could someone tell me how to debug this issue? >>> >> Please share complete log to analyze this, but this user may be logged >> in before upgrade and we just clean its session after upgrade. >> >> >> >>> >>> Martin can probably help as well here, adding also Greg and Alexander. >>> >>> >>> >>> 02.02.2017 14:19, Sandro Bonazzola пишет: Hi, did you install/update to 4.1.0? Let us know your experience! We end up knowing only when things doesn't work well, let us know it works fine for you :-) If you're not planning an update to 4.1.0 in the near future, let us know why. Maybe we can help. Thanks! -- Sandro Bonazzola Better technology. Faster innovation. Powered by community collaboration. See how it works at redhat.com ___ Users mailing listUsers@ovirt.orghttp://lists.ovirt.org/mailman/listinfo/users ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users >>> >>> >>> -- >>> Sandro Bonazzola >>> Better technology. Faster innovation. Powered by community collaboration. >>> See how it works at redhat.com >>> >> >> >> ___ >> Users mailing list >> Users@ovirt.org >> http://lists.ovirt.org/mailman/listinfo/users >> >> > > ___ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > > ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] [Call for feedback] did you install/update to 4.1.0?
All upgrades are went smoothly! Thanks for the release. There is an minor problem I saw: After upgrading from 4.0.6 to 4.1 the GUI dialog for moving the disks from one Storage to another is not rendered correctly when multiple disks(>8) are selected for move. please see the attachment: *** Dr. Arman Khalatyan eScience -SuperComputing Leibniz-Institut für Astrophysik Potsdam (AIP) An der Sternwarte 16, 14482 Potsdam, Germany *** On Sat, Feb 4, 2017 at 5:08 PM, Martin Perina wrote: > > > On Fri, Feb 3, 2017 at 9:24 AM, Sandro Bonazzola > wrote: > >> >> >> On Fri, Feb 3, 2017 at 9:14 AM, Yura Poltoratskiy >> wrote: >> >>> I've done an upgrade of ovirt-engine tomorrow. There were two problems. >>> >>> The first - packages from epel repo, solved by disable repo and >>> downgrade package to an existing version in ovirt-release40 repo (yes, >>> there is info in documentation about epel repo). >>> >>> The second (and it is not only for current version) - run the >>> engine-setup always not complete successfully because cat not start >>> ovirt-engine-notifier.service after upgrade, and the error in notifier is >>> that there is no MAIL_SERVER. Every time I am upgrading engine I have the >>> same error. Than I add MAIL_SERVER=127.0.0.1 to >>> /usr/share/ovirt-engine/services/ovirt-engine-notifier/ovirt-engine-notifier.conf >>> and start notifier without problem. Is it my mistake? >>> >> > Please never change anything in /usr/share/ovirt-engine, those files are > always overwritten during upgrade. If you need change any option in > ovirt-engine-notifier, please create new configuration file in > /etc/ovirt-engine/notifier/notifier.conf.d directory. For example if you > need to set MAIL_SERVER please create > /etc/ovirt-engine/notifier/notifier.conf.d/99-custom.conf > with following content: > > MAIL_SERVER=127.0.0.1 > > After saving the file please restart ovirt-engine-notifier service: > > systemctl restart ovirt-engine-notifier > > >> Adding Martin Perina, he may be able to assist you on this. >> >> >> >>> And one more question. In Events tab I can see "User vasya@internal >>> logged out.", but there are no message that 'vasya' logged in. Could >>> someone tell me how to debug this issue? >>> >> > Please share complete log to analyze this, but this user may be logged in > before upgrade and we just clean its session after upgrade. > > > >> >> Martin can probably help as well here, adding also Greg and Alexander. >> >> >> >> >>> >>> 02.02.2017 14:19, Sandro Bonazzola пишет: >>> >>> Hi, >>> did you install/update to 4.1.0? Let us know your experience! >>> We end up knowing only when things doesn't work well, let us know it >>> works fine for you :-) >>> >>> If you're not planning an update to 4.1.0 in the near future, let us >>> know why. >>> Maybe we can help. >>> >>> Thanks! >>> -- >>> Sandro Bonazzola >>> Better technology. Faster innovation. Powered by community collaboration. >>> See how it works at redhat.com >>> >>> >>> ___ >>> Users mailing >>> listUsers@ovirt.orghttp://lists.ovirt.org/mailman/listinfo/users >>> >>> >>> >>> ___ >>> Users mailing list >>> Users@ovirt.org >>> http://lists.ovirt.org/mailman/listinfo/users >>> >>> >> >> >> -- >> Sandro Bonazzola >> Better technology. Faster innovation. Powered by community collaboration. >> See how it works at redhat.com >> > > > ___ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > > ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] How to benefit from pci-e ssd??
On Sun, Feb 5, 2017 at 2:46 PM, Arman Khalatyan wrote: > Hi, I wondered if there some setup where we can benefit from pci-e ssds? > One possible way is pci passthrough but then the vm does not migrate > anymore(am I right?). Right, if you use host resources, you will not be able to migrate. You have to choose between being able to run on any host and having better performance. > Another way to share nvme over iscsi, but any software layer between vm and > nvme is dumping the performance(maybe worth to try iser or srp?) It will be interesting to try sharing over iscsi, your host networking is probably going to be the limitation. We are working now on a localdisk hook, that will allow you to run a vm using a fast ssd on a host, using disks and templates on shared storage. You can track the development here: https://gerrit.ovirt.org/71272 There is an initial draft for the feature page here: https://github.com/nirs/ovirt-site/commit/f63da31b873943e2ca3290e38d5a12b896195f0f Nir > > Ps > I have seen that sime cloud providers are offering ssd vms, what does it > mean?:) > > > ___ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
[ovirt-users] How to benefit from pci-e ssd??
Hi, I wondered if there some setup where we can benefit from pci-e ssds? One possible way is pci passthrough but then the vm does not migrate anymore(am I right?). Another way to share nvme over iscsi, but any software layer between vm and nvme is dumping the performance(maybe worth to try iser or srp?) Ps I have seen that sime cloud providers are offering ssd vms, what does it mean?:) ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] How to update ovirt nodes
(Re-adding the list) On Sun, Feb 5, 2017 at 12:23 PM, Shalabh Goel wrote: > Yes and no. First I did install ovirtrelease41 rpm in both nodes. Then in > one of the nodes, I started upgrade from the court engine administration > portal. > The second node developed some other problem and hence I had to remove it > from the court engine and I reinstalled ovirt 4.0.3 ng and then upgraded it > before adding it to the engine. It got upgraded successfully and I rebooted > and logged into 4.1 too. > > But I am getting the same error for both the nodes. The first one was moved > to non operational state by the engine. The second one is not getting added. > > My VMs are in a third storage node *(NFS). I have not yet upgraded it since > other two upgrades failed. > > BTW I have changed the compatibility of cluster and data centre to 4.1. Your current state is not fully clear. Can you please describe it in detail? How many hosts do you have? What's the state of each in the engine? Do you have VMs that are ok? And if so, is it important to not stop them? In any case, if you have hosts that do not have VMs on them, and in whatever state, it's probably simplest to move them to maintenance, remove from the engine, reinstall the OS, then try to add them. If you try to add a host and it fails, please check/attach engine.log and host-deploy log. If you fail to activate a host, please check/attach engine.log. Best, > > Thanks > > Shalabh Goel > > On 05-Feb-2017 12:19 PM, "Yedidyah Bar David" wrote: >> >> On Fri, Feb 3, 2017 at 6:35 AM, Shalabh Goel >> wrote: >> > Hi can u just confirm something for me? I had to change the existing >> > ovirt-4.0 repos to ovirt 4.1 (by replacing 40 by 41 in the repo files). >> >> That's mostly ok, but generally you should install ovirt-release41.rpm. >> >> It will also add/update ovirt-*-dependencies.repo . >> >> > And >> > then I ran yum update. And rebooted the nodes and booted into >> > ovirt-node4.1. >> >> Didn't you move to maintenance? Were your VMs migrated correctly? >> >> > Is the procedure correct? >> > >> > Thanks >> > >> > Shalabh Goel >> > >> > On Thu, Feb 2, 2017 at 2:02 PM, Yedidyah Bar David >> > wrote: >> >> >> >> On Thu, Feb 2, 2017 at 8:14 AM, Shalabh Goel >> >> wrote: >> >> > Hi >> >> > >> >> > Ovirt 4.1 has been released, I want to to know how to upgrade the >> >> > Ovirt >> >> > nodes to 4.1. I was able to upgrade ovirt-engine but I could not find >> >> > how to >> >> > upgrade node. >> >> >> >> Something like: >> >> >> >> 1. Move node to maintenance >> >> 2. Add 4.1 repos >> >> 3. yum update >> >> 4. reboot >> >> 5. Activate (exit maintenance) >> >> >> >> See also: >> >> >> >> https://www.ovirt.org/node/ >> >> http://www.ovirt.org/node/faq/ >> >> >> >> If in "node" you referred to ovirt-node, and not a regular OS install, >> >> then >> >> the flow is exactly the same, but what actually happens inside it is >> >> very >> >> different - the entire OS image is replaced. >> >> >> >> You might want to check also: >> >> >> >> >> >> >> >> http://www.ovirt.org/develop/release-management/features/engine/upgrademanager/ >> >> >> >> Best, >> >> -- >> >> Didi >> > >> > >> > >> > >> > -- >> > Shalabh Goel >> >> >> >> -- >> Didi -- Didi ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] oVirt Engine 4.1 fails on specifying interface for ovirtmgmt
Great to hear Karli :) Thank you! On Sun, Feb 5, 2017 at 11:03 AM, Karli Sjöberg wrote: > > Den 5 feb. 2017 9:30 fm skrev Michael Burman : > > > > Hi > > > > Karil, it is seems like you didn't configured the vlan device eno1.1 > properly before you run hosted-engine --deploy. > > How did you configured it? > > If the vlan device was properly configured then you should have seen > something like : > > Please indicate a nic to set ovirtmgmt bridge on: (eno1, eno1.1) [eno1]: > > No that wasn't the problem, the network was fine, since I was connected to > it over SSH:) > > What was wrong was that I already had a bridge called 'Public' on that > interface and the deploy couldn't handle that. Maybe RFE material... I just > removed the bridge and deployed again, and then I could specify 'eno1.1'. I > am bummed over the fact that I couldn't create the ovirtmgmt bridge before > the deploy, it just bombed, apparently by design: > https://bugzilla.redhat.com/show_bug.cgi?id=1317125 > > I know how to configure it correctly, and if I don't, I won't blame you > for my mistakes! > > Other than that I have had no problems deploying 4.1 hosted engine. Really > nice new dashboard and I love the new import from KVM feature, which I used > to empty my old environment before reinstalling as the second hosted engine > host. > > Great job everyone! It works great! > > /K > > > > > Regards, > > > > On Sun, Feb 5, 2017 at 9:03 AM, Yedidyah Bar David > wrote: > >> > >> On Fri, Feb 3, 2017 at 3:19 PM, Karli Sjöberg > wrote: > >> > Heya! > >> > > >> > I´m trying to complete 'hosted-engine --deploy' but I´m stuck at: > >> > Please indicate a nic to set ovirtmgmt bridge on: (eno1) [eno1]: > eno1.1 > >> > [ ERROR ] Invalid value > >> > >> This should generally work. Is the vlan interface configured, before you > >> run deploy? > >> > >> Please share both runs' logs. Thanks. > >> > >> Adding Simone. > >> > >> > > >> > As you can see it´s a vlan-tagged interface. If I type in just 'eno1', > >> > the setup continues but fails obviously since it´s the wrong network. > >> > > >> > Any pointers? > >> > > >> > /K > >> > ___ > >> > Users mailing list > >> > Users@ovirt.org > >> > http://lists.ovirt.org/mailman/listinfo/users > >> > >> > >> > >> -- > >> Didi > >> ___ > >> Users mailing list > >> Users@ovirt.org > >> http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > > > -- > > Michael Burman > > RedHat Israel, RHV-M Network QE > > > > Mobile: 054-5355725 > > IRC: mburman > -- Michael Burman RedHat Israel, RHV-M Network QE Mobile: 054-5355725 IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] oVirt Engine 4.1 fails on specifying interface for ovirtmgmt
Den 5 feb. 2017 9:30 fm skrev Michael Burman : > > Hi > > Karil, it is seems like you didn't configured the vlan device eno1.1 properly > before you run hosted-engine --deploy. > How did you configured it? > If the vlan device was properly configured then you should have seen > something like : > Please indicate a nic to set ovirtmgmt bridge on: (eno1, eno1.1) [eno1]: No that wasn't the problem, the network was fine, since I was connected to it over SSH:) What was wrong was that I already had a bridge called 'Public' on that interface and the deploy couldn't handle that. Maybe RFE material... I just removed the bridge and deployed again, and then I could specify 'eno1.1'. I am bummed over the fact that I couldn't create the ovirtmgmt bridge before the deploy, it just bombed, apparently by design: https://bugzilla.redhat.com/show_bug.cgi?id=1317125 I know how to configure it correctly, and if I don't, I won't blame you for my mistakes! Other than that I have had no problems deploying 4.1 hosted engine. Really nice new dashboard and I love the new import from KVM feature, which I used to empty my old environment before reinstalling as the second hosted engine host. Great job everyone! It works great! /K > > Regards, > > On Sun, Feb 5, 2017 at 9:03 AM, Yedidyah Bar David wrote: >> >> On Fri, Feb 3, 2017 at 3:19 PM, Karli Sjöberg wrote: >> > Heya! >> > >> > I´m trying to complete 'hosted-engine --deploy' but I´m stuck at: >> > Please indicate a nic to set ovirtmgmt bridge on: (eno1) [eno1]: eno1.1 >> > [ ERROR ] Invalid value >> >> This should generally work. Is the vlan interface configured, before you >> run deploy? >> >> Please share both runs' logs. Thanks. >> >> Adding Simone. >> >> > >> > As you can see it´s a vlan-tagged interface. If I type in just 'eno1', >> > the setup continues but fails obviously since it´s the wrong network. >> > >> > Any pointers? >> > >> > /K >> > ___ >> > Users mailing list >> > Users@ovirt.org >> > http://lists.ovirt.org/mailman/listinfo/users >> >> >> >> -- >> Didi >> ___ >> Users mailing list >> Users@ovirt.org >> http://lists.ovirt.org/mailman/listinfo/users > > > > > -- > Michael Burman > RedHat Israel, RHV-M Network QE > > Mobile: 054-5355725 > IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] oVirt Engine 4.1 fails on specifying interface for ovirtmgmt
Hi Karil, it is seems like you didn't configured the vlan device eno1.1 properly before you run hosted-engine --deploy. How did you configured it? If the vlan device was properly configured then you should have seen something like : Please indicate a nic to set ovirtmgmt bridge on: (eno1, eno1.1) [eno1]: Regards, On Sun, Feb 5, 2017 at 9:03 AM, Yedidyah Bar David wrote: > On Fri, Feb 3, 2017 at 3:19 PM, Karli Sjöberg > wrote: > > Heya! > > > > I´m trying to complete 'hosted-engine --deploy' but I´m stuck at: > > Please indicate a nic to set ovirtmgmt bridge on: (eno1) [eno1]: eno1.1 > > [ ERROR ] Invalid value > > This should generally work. Is the vlan interface configured, before you > run deploy? > > Please share both runs' logs. Thanks. > > Adding Simone. > > > > > As you can see it´s a vlan-tagged interface. If I type in just 'eno1', > > the setup continues but fails obviously since it´s the wrong network. > > > > Any pointers? > > > > /K > > ___ > > Users mailing list > > Users@ovirt.org > > http://lists.ovirt.org/mailman/listinfo/users > > > > -- > Didi > ___ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > -- Michael Burman RedHat Israel, RHV-M Network QE Mobile: 054-5355725 IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
