: [WISPA] ANOTHER Apex firmware upgrade problem
1. 17dBm / 17 dBm
2. Speed is the same on both sides.
3. (trango-view)# linktest 1
LOCK RSSI MSEBER TX
RX
1 1 -41.10 dBm -34.40 dB 0.00E+00256QAM
256QAM
(trango-view)#
(trango
RPS is off. We learned this lesson early on.
I've been pinging the other side all night and I'll see a few packets
get through occasionally. 200 packets made it through out of 2
last night.
Still hoping someone has some ideas!
Never mind about the few packets getting through. I think that is
just OSPF changes and it seeing the other end of the link.
WISPA Wants You! Join today!
http://signup.wispa.org/
I turned ACM off and ATPC and some packets will get through
occassionally. Still seeing 97% packet loss.
WISPA Wants You! Join today!
http://signup.wispa.org/
Post more info
Copy sysinfo from each end of the radio something might stand out.
Or assuming your RF is all locked and rssi and MSE are OK then its a feeder
port issue so just post sysinfo 4 to view the port status is ON for your
cable If not you can set the port speed at 100Nase-T Autoneg and
Sorry I can't help but is it me or do I see a lot of posts on these units
regarding firmware changes.
I can't remember the last time I did a firmware upgrade on a licensed link.
-B-
Sent from my Verizon Wireless BlackBerry
-Original Message-
From: can...@believewireless.net
I think Trango users have to so that it fixes auto rate modulating.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
“Success is not final, failure is not fatal: it is the courage to
continue that counts.”
--- Winston Churchill
On Sat, Jun 26,
We can access the units via their IBM addresses but they won't pass
traffic. We have rebooted the radios, power cycled them, and nothing
happens.
Interestingly, the Mikrotik on one end of the link is showing up in
the neighbor list. So something is getting through.
Did you check:
(1) power level on each side
(2) speed settings (same modulation and channel size on each side)
(3) what does the linktest show on each side?
Travis
Microserv
can...@believewireless.net wrote:
We can access the units via their IBM addresses but they won't pass
traffic. We have
That firmware has been out for almost 6 months now... no other updates
during that time.
Travis
Josh Luthman wrote:
I think Trango users have to so that it fixes auto rate modulating.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
1. 17dBm / 17 dBm
2. Speed is the same on both sides.
3. (trango-view)# linktest 1
LOCK RSSI MSEBER TX
RX
1 1 -41.10 dBm -34.40 dB 0.00E+00256QAM
256QAM
(trango-view)#
(trango-config)# linktest 1
Hi,
During the upgrade process, did it give any errors? You did all 4 or 5
files, correct? Have you tried doing them again and re-flashing each one
as you go?
Travis
can...@believewireless.net wrote:
1. 17dBm / 17 dBm
2. Speed is the same on both sides.
3. (trango-view)# linktest 1
12 matches
Mail list logo
