[zd1211-devs] zd1211rw problems, bit rate, icwonfig
I am trying to get my Linksys USB Network Adapter with Wi-Fi finder Linksys WUSBF54G 13b1:0024 to work with zd1211rw. Previously I've had success version getting it to work with the old zd1211 driver. I'm running Ubuntu feisty, which has kernel 2.6.19-7. zd1211rw is snapshot 2006-12-14, with an edited zd_usb.c with a new {USB_DEVICE(0x13b1, 0x0024), .driver_info = DEVICE_ZD1211B} I seem to get the usb adapter recognized, but the Bit Rate is only 1 Mb/s and I can't get an dhcp offer. I tried to set another bit rate with iwconfig (sudo iwconfig eth1 rate 11M), but it doesn't change. The output of iwconfig looks the same next time. Any ideas how I can get further or what I'm doing wrong? /Henrik Hjelte dmesg: [ 1047.992000] usb 3-3: new high speed USB device using ehci_hcd and address 8 [ 1048.124000] usb 3-3: configuration #1 chosen from 1 choice [ 1048.156000] usb 3-3: firmware version 0x4810 and device bootcode version 0x4802 differ [ 1048.264000] zd1211rw 3-3:1.0: firmware version 4725 [ 1048.308000] zd1211rw 3-3:1.0: zd1211b chip 13b1:0024 v4802 high00-14-bf AL2230_RF pa0 [ 1048.308000] zd1211rw 3-3:1.0: eth1 [ 1048.432000] ADDRCONF(NETDEV_UP): eth1: link is not ready iwconfig: eth1 IEEE 802.11b/g ESSID:O Nickname:zd1211 Mode:Managed Frequency:2.412 GHz Access Point: Invalid Bit Rate=1 Mb/s Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.phpp=sourceforgeCID=DEVDEV ___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
Re: [zd1211-devs] zd1211rw problems, bit rate, icwonfig
Henrik Hjelte-2 wrote: I am trying to get my Linksys USB Network Adapter with Wi-Fi finder Linksys WUSBF54G 13b1:0024 to work with zd1211rw. Previously I've had success version getting it to work with the old zd1211 driver. I'm running Ubuntu feisty, which has kernel 2.6.19-7. zd1211rw is snapshot 2006-12-14, with an edited zd_usb.c with a new {USB_DEVICE(0x13b1, 0x0024), .driver_info = DEVICE_ZD1211B} I seem to get the usb adapter recognized, but the Bit Rate is only 1 Mb/s and I can't get an dhcp offer. I tried to set another bit rate with iwconfig (sudo iwconfig eth1 rate 11M), but it doesn't change. The output of iwconfig looks the same next time. Any ideas how I can get further or what I'm doing wrong? /Henrik Hjelte dmesg: [ 1047.992000] usb 3-3: new high speed USB device using ehci_hcd and address 8 [ 1048.124000] usb 3-3: configuration #1 chosen from 1 choice [ 1048.156000] usb 3-3: firmware version 0x4810 and device bootcode version 0x4802 differ [ 1048.264000] zd1211rw 3-3:1.0: firmware version 4725 [ 1048.308000] zd1211rw 3-3:1.0: zd1211b chip 13b1:0024 v4802 high00-14-bf AL2230_RF pa0 [ 1048.308000] zd1211rw 3-3:1.0: eth1 [ 1048.432000] ADDRCONF(NETDEV_UP): eth1: link is not ready iwconfig: eth1 IEEE 802.11b/g ESSID:O Nickname:zd1211 Mode:Managed Frequency:2.412 GHz Access Point: Invalid Bit Rate=1 Mb/s Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.phpp=sourceforgeCID=DEVDEV ___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs I have the same problem... -- View this message in context: http://www.nabble.com/zd1211rw-problems%2C-bit-rate%2C-icwonfig-tf2829350.html#a7900561 Sent from the zd1211-devs mailing list archive at Nabble.com. - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.phpp=sourceforgeCID=DEVDEV ___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
[zd1211-devs] wireless-dev dont connect
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 Hi all, i play with wireless-dev and wireless-2.6 git's (to make to work my onboard bcm43xx) in these kernels i cant connect with my zd1211 to the ap's i can scan and see the ap, the log say associted but i do not get the ip from my dhcp (also i test to put a fixed address) i dont have this problem on 2.6.19 (vanilla) from kernel.org when iwlist scann or ifconfig up : zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 9 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003f7b0 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x001 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 9 pwr_int 0x54 zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: set_channel() channel 10 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 10 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003f7b0 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00b3331 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 10 pwr_int 0x5c zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: set_channel() channel 11 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 11 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003e7b0 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x001 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 11 pwr_int 0x5c zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 SoftMAC: Scanning finished SoftMAC: Queueing Authentication Request to 00:80:c8:ac:aa:06 SoftMAC: Cannot associate without being authenticated, requested authentication zd1211rw 2-6:1.0: set_channel() channel 6 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 6 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003f7a0 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00b3331 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 6 pwr_int 0x5c zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 SoftMAC: Sent Authentication Request to 00:80:c8:ac:aa:06. SoftMAC: Open Authentication completed with 00:80:c8:ac:aa:06 zd1211rw 2-6:1.0: set_channel() channel 6 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 6 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003f7a0 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00b3331 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 6 pwr_int 0x5c zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 SoftMAC: sent association request! SoftMAC: associated! zd1211rw 2-6:1.0: housekeeping_disable() zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: zd_usb_disable_int() urb c4c7a6c0 killed zd1211rw 2-6:1.0: zd_usb_enable_int() zd1211rw 2-6:1.0: zd_usb_enable_int() submit urb cde0b3c0 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_rf_set_channel() channel: 1 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x003f790 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x001 bits 24 zd1211rw 2-6:1.0: zd_usb_rfwrite() value 0x00d bits 24 zd1211rw 2-6:1.0: update_pwr_int() channel 1 pwr_int 0x54 zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: zd_usb_enable_rx() zd1211rw 2-6:1.0: housekeeping_enable() when ifconfig down : zd1211rw 2-6:1.0: housekeeping_disable() zd1211rw 2-6:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 - 0x20 zd1211rw 2-6:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 - 0xa0 zd1211rw 2-6:1.0: zd_usb_disable_int() urb c4c7a7c0 killed [EMAIL PROTECTED]:~$ sudo iwconfig eth1 eth1 IEEE 802.11b/g ESSID:docksud Nickname:zd1211 Mode:Managed Frequency:2.462 GHz Access Point: 00:80:C8:AC:AA:06 Bit Rate=1 Mb/s Encryption key:off Link Quality=88/100 Signal level=97/100 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Listening on LPF/eth1/00:02:72:4a:2e:9a Sending on LPF/eth1/00:02:72:4a:2e:9a Sending on Socket/fallback/fallback-net DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 7 receive_packet failed on eth1: Network is down DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 8 thanka for you help -BEGIN PGP