Re: [zd1211-devs] wpa-0.5.7...don't work!
arandamandi wrote:
>
>
>
> arandamandi wrote:
>>
>> Hi
>> Zd1211rw
>> zyxel g-air 220
>> kernel 2.6.20.3
>>
>> with 0.4.9 wpa_supplicant..all ok,connect,autenticate,etc..
>> with 0.5.7...no autentication message(SoftMAC: Open Authentication
>> completed with ...)
>> How to solve?
>> Thanks
>>
> I have
> this error
> zd1211rw 1-4:1.0: error ioread32(CR_REG1): -11
> Here's my config files
>
> # /etc/rc.d/rc.inet1.conf
> #
> # This file contains the configuration settings for network interfaces.
> # If USE_DHCP[interface] is set to "yes", this overrides any other
> settings.
> # If you don't have an interface, leave the settings null ("").
>
> # You can configure network interfaces other than eth0,eth1... by setting
> # IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
> # or empty, it is assumed you're configuring eth.
>
> # Several other parameters are available, the end of this file contains a
> # comprehensive set of examples.
>
> #
> =
>
> # Config information for eth0:
> #IPADDR[0]="192.168.0.3"
> #NETMASK[0]="255.255.255.0"
> #USE_DHCP[0]=""
> #DHCP_HOSTNAME[0]=""
>
> # Config information for eth1:
> IPADDR[1]=""
> NETMASK[1]=""
> USE_DHCP[1]=""
> DHCP_HOSTNAME[1]=""
>
> # Config information for eth2:
> IPADDR[2]=""
> NETMASK[2]=""
> USE_DHCP[2]=""
> DHCP_HOSTNAME[2]=""
>
> # Config information for eth3:
> IPADDR[3]=""
> NETMASK[3]=""
> USE_DHCP[3]=""
> DHCP_HOSTNAME[3]=""
>
> # Default gateway IP address:
> GATEWAY="192.168.0.1"
>
> # Change this to "yes" for debugging output to stdout. Unfortunately,
> # /sbin/hotplug seems to disable stdout so you'll only see debugging
> output
> # when rc.inet1 is called directly.
> DEBUG_ETH_UP="no"
>
> ## Example config information for wlan0. Uncomment the lines you need and
> fill
> ## in your info. (You may not need all of these for your wireless
> network)
> IFNAME[4]="wlan0"
> IPADDR[4]="192.168.0.2"
> NETMASK[4]="255.255.255.0"
> #USE_DHCP[4]="yes"
> #DHCP_HOSTNAME[4]="icculus-wireless"
> #DHCP_KEEPRESOLV[4]="yes"
> #DHCP_KEEPNTP[4]="yes"
> #DHCP_KEEPGW[4]="yes"
> #DHCP_IPADDR[4]=""
> WLAN_ESSID[4]=Slack
> WLAN_MODE[4]=Managed
> WLAN_RATE[4]="54M auto"
> WLAN_CHANNEL[4]="11"
> ##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
> ##WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP
> ##WPAPSK=12096A0EAFAD563B268BAD01CAF TxRate=0"
> WLAN_WPA[4]="wpa_supplicant"
> WLAN_WPADRIVER[4]="wext"
>
> ## Some examples of additional network parameters that you can use.
> ## Config information for wlan0:
> #IFNAME[4]="wlan0" # Use a different interface name nstead of
> # the default 'eth4'
> #HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
> #MTU[4]="" # The default MTU is 1500, but you might
> need
> # 1360 when you use NAT'ed IPSec traffic.
> #DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client
> to
> # wait for server resonse is 60 seconds,
> but
> # you might want a shorter wait.
> #DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf
> overwritten
> #DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
> #DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to
> change
> # your default gateway
> #DHCP_IPADDR[4]="" # Request a specific IP address from the
> DHCP
> # server
> #WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter
> # defined in rc.wireless.conf, by
> prepending
> # 'WLAN_' to the parameter's name. Useful
> for
> # those with multiple wireless interfaces.
> #WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
> # Some drivers require a private ioctl to
> be
> # set through the iwpriv command. If more
> than
> # one is required, you can place them in
> the
> # IWPRIV parameter (space-separated, see
> the
> # example).
>
> wpa_supplicant.conf
>
> See /usr/doc/wpa_supplicant-0.4.8/wpa_supplicant.conf.sample
> # for many more options that you can use in this file.
>
> # This line enables the use of wpa_cli which is used by rc.wireless
> # if possible (to check for successful association)
> ctrl_interface=/var/run/wpa_supplicant
> # By default, only root (group 0) may use wpa_cli
> ctrl_interface_group=0
> eapol_version=1
> ap_scan=1
> fast_reauth=1
>
> # WPA protected network, supply your own ESSID and WPAPSK here:
> network={
> scan_ssid=0
> ssid="Slack"
> proto=WPA
> key_mgmt=WPA-PSK
> pairwise=CCMP TKIP
> group=C
Re: [zd1211-devs] wpa-0.5.7...don't work!
arandamandi wrote:
>
> Hi
> Zd1211rw
> zyxel g-air 220
> kernel 2.6.20.3
>
> with 0.4.9 wpa_supplicant..all ok,connect,autenticate,etc..
> with 0.5.7...no autentication message(SoftMAC: Open Authentication
> completed with ...)
> How to solve?
> Thanks
>
I have
this error
zd1211rw 1-4:1.0: error ioread32(CR_REG1): -11
Here's my config files
# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").
# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth.
# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.
#
=
# Config information for eth0:
#IPADDR[0]="192.168.0.3"
#NETMASK[0]="255.255.255.0"
#USE_DHCP[0]=""
#DHCP_HOSTNAME[0]=""
# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""
# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""
# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""
# Default gateway IP address:
GATEWAY="192.168.0.1"
# Change this to "yes" for debugging output to stdout. Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"
## Example config information for wlan0. Uncomment the lines you need and
fill
## in your info. (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
IPADDR[4]="192.168.0.2"
NETMASK[4]="255.255.255.0"
#USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]=Slack
WLAN_MODE[4]=Managed
WLAN_RATE[4]="54M auto"
WLAN_CHANNEL[4]="11"
##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
##WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP
##WPAPSK=12096A0EAFAD563B268BAD01CAF TxRate=0"
WLAN_WPA[4]="wpa_supplicant"
WLAN_WPADRIVER[4]="wext"
## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0" # Use a different interface name nstead of
# the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might
need
# 1360 when you use NAT'ed IPSec traffic.
#DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client to
# wait for server resonse is 60 seconds, but
# you might want a shorter wait.
#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf
overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to
change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the
DHCP
# server
#WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter
# defined in rc.wireless.conf, by prepending
# 'WLAN_' to the parameter's name. Useful
for
# those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more
than
# one is required, you can place them in the
# IWPRIV parameter (space-separated, see the
# example).
wpa_supplicant.conf
See /usr/doc/wpa_supplicant-0.4.8/wpa_supplicant.conf.sample
# for many more options that you can use in this file.
# This line enables the use of wpa_cli which is used by rc.wireless
# if possible (to check for successful association)
ctrl_interface=/var/run/wpa_supplicant
# By default, only root (group 0) may use wpa_cli
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
# WPA protected network, supply your own ESSID and WPAPSK here:
network={
scan_ssid=0
ssid="Slack"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
#psk="**"
psk=***
}
rc.wireless.conf
VERBOSE=0
WPA="y"
case "$HWADDR" in
00:**:**:*)
INFO="Configurazione wireless usb"
ESSID="Slack"
RATE="54M"
MODE="Managed"
CHANNEL="11"
esac
#attiva il wpa se in rc.wireless.conf
Re: [zd1211-devs] wpa-0.5.7...don't work!
uberpinguin wrote: > > On Sat, 2007-03-24 at 19:46 -0700, arandamandi wrote: >> Hi >> Zd1211rw >> zyxel g-air 220 >> kernel 2.6.20.3 >> >> with 0.4.9 wpa_supplicant..all ok,connect,autenticate,etc.. >> with 0.5.7...no autentication message(SoftMAC: Open Authentication >> completed >> with ...) >> How to solve? >> Thanks > Probably a configuration issue; I've been using .5.7 for quite some > time without issue. > -- > Build a person a fire, and they may be warm for a day. > Set that person on fire, and they will be warm for the rest of their > life. > GnuPG Public Key ID 1024D/203C7431. > Public Key Available From http://keyserv.nic-se.se:11371/#extract > > - > Take Surveys. Earn Cash. Influence the Future of IT > Join SourceForge.net's Techsay panel and you'll get the chance to share > your > opinions on IT & business topics through brief surveys-and earn cash > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV > ___ > Zd1211-devs mailing list - http://zd1211.ath.cx/ > Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs > please..i'm on slackware-current some how-to for configure zd1211 with new wpa? Thanks -- View this message in context: http://www.nabble.com/wpa-0.5.7...don%27t-work%21-tf3461098.html#a9667791 Sent from the zd1211-devs mailing list archive at Nabble.com. - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV ___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
Re: [zd1211-devs] wpa-0.5.7...don't work!
On Sat, 2007-03-24 at 19:46 -0700, arandamandi wrote: > Hi > Zd1211rw > zyxel g-air 220 > kernel 2.6.20.3 > > with 0.4.9 wpa_supplicant..all ok,connect,autenticate,etc.. > with 0.5.7...no autentication message(SoftMAC: Open Authentication completed > with ...) > How to solve? > Thanks Probably a configuration issue; I've been using .5.7 for quite some time without issue. -- Build a person a fire, and they may be warm for a day. Set that person on fire, and they will be warm for the rest of their life. GnuPG Public Key ID 1024D/203C7431. Public Key Available From http://keyserv.nic-se.se:11371/#extract signature.asc Description: This is a digitally signed message part - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
[zd1211-devs] wpa-0.5.7...don't work!
Hi Zd1211rw zyxel g-air 220 kernel 2.6.20.3 with 0.4.9 wpa_supplicant..all ok,connect,autenticate,etc.. with 0.5.7...no autentication message(SoftMAC: Open Authentication completed with ...) How to solve? Thanks -- View this message in context: http://www.nabble.com/wpa-0.5.7...don%27t-work%21-tf3461098.html#a9656764 Sent from the zd1211-devs mailing list archive at Nabble.com. - Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV ___ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
